Study guide

9.1 Prime Mover and Semi-trailer Procedures

Tasmania Heavy Vehicle Knowledge Test — Free Study Guide 2026 Exam

Track your progress as you read

Finished sections get a check mark.

1 1. Licence Classes and the Knowledge Test

1.1 Choosing LR, MR, HR, HC or MC 1.2 Eligibility and Assessment Pathways 1.3 Learner, Provisional and Gearbox Conditions 1.4 Test Administration and Licence Recognition

2 2. Fitness, Alcohol, Drugs and Fatigue

2.1 Medical Fitness, Seatbelts and Safe Cab Access 2.2 Alcohol Rules and Breath Testing 2.3 Drugs, Medicines and Driving 2.4 Recognising and Managing Fatigue

3 3. Work, Rest and Transport Responsibilities

3.1 Standard Hours and Approved Alternative Hours 3.2 Work Diaries, Records and Chain of Responsibility

4 4. Observation, Space and Vehicle Control

4.1 Observation, Road Position and Hazard Planning 4.2 Following Gaps, Separation and Stopping Distance 4.3 Brake Failure, Skids and Combination Stability 4.4 Hills, Curves, Weather and Animals

5 5. Heavy Vehicle Signs and Manoeuvres

5.1 Clearance, Load, Entry and Route Restrictions 5.2 Turning, Lane Position and Turning Signs 5.3 Speed Caps, Overtaking, Lane Changes and Reversing 5.4 Bus Rules and Heavy or Long Vehicle Parking

6 6. Breakdowns, Warning Triangles and Fire

6.1 Breakdown Safety and Warning Triangles 6.2 Vehicle Fire and Emergency Assistance

7 7. General Tasmanian Traffic Rules

7.1 Signs, Signals and Intersection Priority 7.2 Roundabouts, Merging and Road Markings 7.3 Railway and Pedestrian Crossings 7.4 Speed Zones, School Buses, Cyclists and Emergency Vehicles 7.5 Parking, Distraction, Restraints and Crash Duties

8 8. Roadworthiness, Brakes and Transmission

8.1 Pre-departure Checks and Maintenance Reports 8.2 Wheels, Tyres, Lights and Rear Marking Plates 8.3 Air Brake Architecture, Parking Brakes and ABS 8.4 Handbook Brake Tests and Fault Decisions 8.5 Gearboxes, Double-declutching and Auxiliary Brakes

9 9. Coupling and Uncoupling

9.1 Prime Mover and Semi-trailer Procedures 9.2 Truck-and-trailer Connections and Final Checks

10 10. Dimensions, Mass and Load Distribution

10.1 Dimensions, Rear Overhang and Projecting Loads 10.2 Ratings, Current Axle Limits and Distribution

11 11. Restraint Principles and Equipment

11.1 Performance Standards and Restraint Methods 11.2 Blocking, Dunnage, Containers, Pipes and Lashings

12 12. Dangerous Goods

12.1 Licensing, Identification and Incident Risks

13 13. Oversize Access and Permits

13.1 Notice Eligibility, Permits and Route Conditions

14 14. Traffic Offences and Licence Consequences

14.1 Demerit Points, Speeding and Other Offences

15 15. Inspections, Defects, Noise and Smoke

15.1 Checking Stations and Return to Roadworthy Use

9.1 Prime Mover and Semi-trailer Procedures

Key Takeaways Explain This Topic AI

Inspect the skid plate, kingpin, turntable jaws, mountings and connections before coupling; the trailer must be secure.

The handbook describes a skid plate slightly below the turntable centre, about 5 cm as an ideal guide, rather than a universal statutory tolerance.

Use the tug test and direct locking checks; resistance alone does not prove correct kingpin engagement.

Last updated: October 2026

Understand what supports the trailer

A semi-trailer transfers front load through its kingpin , skid plate and the prime mover’s fifth wheel , also called the turntable. When uncoupled, its landing gear must support the front safely. A false coupling can allow the trailer to fall or separate, so no single sound, lever position or tug should replace the complete checks.

The handbook gives a general sequence for coupling and uncoupling. Different fifth wheels, turntables, suspension and line arrangements can require variations. Follow the manufacturer’s procedure and practical training for the actual equipment. Do not present a generic sequence as a universal statute or apply an invented kingpin wear tolerance to every coupling.

Prepare and align

Use firm, level ground and keep the prime mover and trailer straight. Check that the surface can support the landing gear and loaded trailer. Secure the trailer with its brakes and chocks as appropriate, keeping people clear of the crush area. On a grade, the handbook particularly emphasises chocks; a suitable location is preferable to improvising on an unsafe slope.

Inspect the skid plate, kingpin, fifth-wheel jaws, release mechanism, mountings, air lines and electrical leads. Look for damage, wear, insecure parts and unsuitable lubrication. Some turntable arrangements use a block behind the kingpin and require a particular locked or unlocked turntable configuration. Confirm the actual equipment rather than assume every fifth wheel swivels in the same way.

Coupling in the handbook sequence

Reverse into a straight aligned position, stop with the plates at the initial contact position and apply the parking brake.

Inspect the trailer and coupling, confirm the jaws are ready and secure the trailer.

Check height. The handbook describes the skid plate slightly lower than the turntable centre, with about 5 cm as an ideal guide. Too low can cause collision with the chassis; too high can prevent correct kingpin capture.

In the handbook’s sequence, connect air hoses and electrical cables, set the tractor-protection control to normal if fitted, apply the trailer brake and check air pressure.

Reverse slowly until the jaws lock, raise landing gear just clear for the specified tug check, and gently test against the trailer brakes in first gear. The handbook calls for repeating this check.

Confirm the release lever is locked, the plates have no improper gap and the jaws correctly surround the kingpin. The pin head must not be sitting on top of the jaws.

Fully raise and secure landing gear, check turning clearances, charge the air system and complete the walk-around, leak and light checks before stowing chocks and moving.

This order differs from some equipment procedures. Use the correct manufacturer’s sequence; do not mix steps from two incompatible procedures. Never reverse with a person between the vehicle units, and stop if alignment or trailer security is uncertain.

Tug and visual checks are complementary

A gentle tug confirms resistance but may not reveal a false or partial engagement. Inspect from a safe position with adequate visibility. Check the locking mechanism around the correct kingpin area, the release mechanism’s secured position and correct plate seating. Do not crawl under an unsupported trailer or place yourself where the vehicle could move.

If a gap remains or locking is doubtful, stop and resolve it through the procedure. Do not drive to 'settle' the connection. Landing gear, lines and suspension must also be in the correct travel position. Allow air suspension time to reach its normal ride position before departure.

Uncoupling in the handbook sequence

  • Stage Handbook action and purpose
  • Secure vehicle Firm level surface, straight alignment, parking/protection controls and trailer security
  • Support trailer Lower landing gear evenly, raise until the specified gap is visible and stow the handle

Release coupling Release jaws through the equipment procedure; relieve load only by safe instructed movement if necessary

Initial separation Move slowly until the fifth wheel is just clear of the skid plate, ensuring the trailer remains secure, then apply the prime mover park brake

Final connections Disconnect and properly stow hoses and cables, then drive slowly clear

The handbook’s general uncoupling order leaves connections until its final stage. Other manufacturer procedures can disconnect earlier. Ensure sufficient line clearance and never stretch or tear the connections. If the actual arrangement cannot accommodate a described movement, follow the approved vehicle procedure instead of forcing the generic sequence.

Check support stability before completing separation. Soft ground requires suitable strong supports under the legs. Do not use an invented universal '30 cm mandatory pull' as proof of stability. Observe the actual fifth-wheel clearance and landing gear, and do not leave a trailer if the support or brakes are doubtful.

Final handover

Stow lines so they remain clean, dry and clear of moving parts. Secure the landing-gear handle. Record coupling faults and arrange repair before use. On recoupling, repeat the complete checks rather than assume yesterday’s connection remains correct.

Key decisions

Secure, align, lock, inspect and check the functional systems. Treat the tug test as one part of verified coupling, and use the actual equipment procedure for the sequence.

Official sources

Official handbook, semi-trailer coupling and uncoupling, pages 66–68 ; manufacturer instructions for the actual fifth wheel, turntable and vehicle. Sources checked 10 October 2026.