Study guide

1.3 Learner, Provisional and Gearbox Conditions

Tasmania Heavy Vehicle Knowledge Test — Free Study Guide 2026 Exam

Track your progress as you read

Finished sections get a check mark.

1 1. Licence Classes and the Knowledge Test

1.1 Choosing LR, MR, HR, HC or MC 1.2 Eligibility and Assessment Pathways 1.3 Learner, Provisional and Gearbox Conditions 1.4 Test Administration and Licence Recognition

2 2. Fitness, Alcohol, Drugs and Fatigue

2.1 Medical Fitness, Seatbelts and Safe Cab Access 2.2 Alcohol Rules and Breath Testing 2.3 Drugs, Medicines and Driving 2.4 Recognising and Managing Fatigue

3 3. Work, Rest and Transport Responsibilities

3.1 Standard Hours and Approved Alternative Hours 3.2 Work Diaries, Records and Chain of Responsibility

4 4. Observation, Space and Vehicle Control

4.1 Observation, Road Position and Hazard Planning 4.2 Following Gaps, Separation and Stopping Distance 4.3 Brake Failure, Skids and Combination Stability 4.4 Hills, Curves, Weather and Animals

5 5. Heavy Vehicle Signs and Manoeuvres

5.1 Clearance, Load, Entry and Route Restrictions 5.2 Turning, Lane Position and Turning Signs 5.3 Speed Caps, Overtaking, Lane Changes and Reversing 5.4 Bus Rules and Heavy or Long Vehicle Parking

6 6. Breakdowns, Warning Triangles and Fire

6.1 Breakdown Safety and Warning Triangles 6.2 Vehicle Fire and Emergency Assistance

7 7. General Tasmanian Traffic Rules

7.1 Signs, Signals and Intersection Priority 7.2 Roundabouts, Merging and Road Markings 7.3 Railway and Pedestrian Crossings 7.4 Speed Zones, School Buses, Cyclists and Emergency Vehicles 7.5 Parking, Distraction, Restraints and Crash Duties

8 8. Roadworthiness, Brakes and Transmission

8.1 Pre-departure Checks and Maintenance Reports 8.2 Wheels, Tyres, Lights and Rear Marking Plates 8.3 Air Brake Architecture, Parking Brakes and ABS 8.4 Handbook Brake Tests and Fault Decisions 8.5 Gearboxes, Double-declutching and Auxiliary Brakes

9 9. Coupling and Uncoupling

9.1 Prime Mover and Semi-trailer Procedures 9.2 Truck-and-trailer Connections and Final Checks

10 10. Dimensions, Mass and Load Distribution

10.1 Dimensions, Rear Overhang and Projecting Loads 10.2 Ratings, Current Axle Limits and Distribution

11 11. Restraint Principles and Equipment

11.1 Performance Standards and Restraint Methods 11.2 Blocking, Dunnage, Containers, Pipes and Lashings

12 12. Dangerous Goods

12.1 Licensing, Identification and Incident Risks

13 13. Oversize Access and Permits

13.1 Notice Eligibility, Permits and Route Conditions

14 14. Traffic Offences and Licence Consequences

14.1 Demerit Points, Speeding and Other Offences

15 15. Inspections, Defects, Noise and Smoke

15.1 Checking Stations and Return to Roadworthy Use

1.3 Learner, Provisional and Gearbox Conditions

Key Takeaways Explain This Topic AI

Heavy vehicle learners must display L plates front and rear, have zero alcohol and obey a maximum of 90 km/h even in a higher speed zone.

The supervising driver must hold the same or higher class, other than learner or provisional, and have held it for at least 12 months.

A2 identifies an automatic restriction and B a synchromesh restriction; check the licence and any upgrade exemption.

Last updated: October 2026

Permission to learn is different from permission to drive alone

A heavy vehicle learner may already hold a full car licence or a lower heavy vehicle class. That prior entitlement does not remove the conditions applying while learning in the higher class. The official handbook makes this distinction explicit: the learning conditions apply whether or not a separate heavy vehicle learner licence is required.

The national class hierarchy determines when a learner authority is needed. Learning in the next class can usually occur on the existing licence. Tasmania also permits a car licence holder to learn MR on their existing licence. Moving more than one class above the existing class requires the appropriate learner authority; a car-to-HR or car-to-HC applicant must check that authority before driving the larger vehicle.

Conditions that apply while learning

Item Requirement Practical meaning

Supervisor Same or higher class, not learner/provisional, held at least 12 months A newly licensed HC friend is not automatically eligible to supervise

  • Position Seated beside the learner; nearest seat for a bus Supervision from a following car does not qualify
  • L plates Clearly displayed front and rear Check both ends of a combination before leaving

Alcohol and drugs Zero alcohol and no drug impairment Holding a full car licence does not restore a car alcohol allowance

Speed Maximum 90 km/h while learning A 110 km/h sign does not authorise 100 km/h for the heavy vehicle learner

Always obey a lower posted limit. The learner cap is a ceiling, not a target. A 60 km/h road remains 60; a steep wet descent may require a much lower safe speed. The vehicle’s own speed cap and any access conditions also continue to apply.

To obtain a learner authority, Service Tasmania checks identity and eligibility. The handbook describes the relevant rigid or combination knowledge test, eyesight check, application and learner fee. A learner condition may appear as an X condition on the licence. Read the issued document for its expiry and conditions. The knowledge-test result has a separate 12-month booking rule; do not confuse that rule with the expiry of the licence itself.

Provisional drivers

P1 and P2 applicants can obtain a heavy vehicle class if they meet its minimum age and non-learner experience requirements. They do not become full licence holders merely because the vehicle class changes. Plates, alcohol requirements, mobile-phone restrictions and any other applicable provisional conditions remain important.

Tasmania’s current general road rule limits P1 non-motorcycle driving to 100 km/h. However, when that person is learning the higher heavy vehicle class, the heavy vehicle learner maximum is 90 km/h. In a question mentioning several limits, identify the activity and choose the lowest applicable ceiling. P2 status also does not remove a vehicle-specific 100 km/h limit for a vehicle above 12 t GVM or a bus above 5 t.

Gearbox conditions

An automatic changes ratios without the driver’s manual gear selection and clutch operation in the conventional sense. A synchromesh manual uses synchronisers to help match the speeds of gearbox components. A non-synchromesh gearbox requires deliberate speed matching, commonly through double-declutching. These are operating skills, not simply different labels for the same transmission.

An assessment in an automatic can result in an A2 restriction. An assessment in a synchromesh vehicle can result in a B condition. Read the condition recorded on the licence; do not assume that every automatic assessment produces B. Transport Services explains that a driver already holding an unrestricted MR or higher licence may retain that unrestricted status on an upgrade despite using an automatic or synchromesh vehicle for assessment. Confirm whether that exemption applies to the actual licence history.

A class entitlement and gearbox entitlement must both cover the proposed vehicle. For example, an HR driver with a restriction cannot assume that a non-synchromesh HR truck is lawful simply because both vehicles are HR. An employer’s request or an empty load does not alter the condition. Arrange the recognised assessment or removal process rather than experimenting on a public road.

Before a learning trip

Check the learner authority if required, the supervisor’s class and tenure, L plates, vehicle suitability and route. Adjust the seat and mirrors with the vehicle stationary. Agree how the supervisor will give instructions and where a safe stop can be made if the learner becomes overloaded. Keep doors closed and every occupant restrained during movement.

If the supervisor becomes unavailable halfway through the day, the learner cannot finish the higher-class trip alone. Park safely and arrange a qualified replacement or a driver with the full entitlement. Treat paperwork, supervision and vehicle controls as one departure check, rather than solving them after entering traffic.

Key decisions

Apply learner conditions to the learning activity, check class and gearbox conditions together, and distinguish the theory-result booking period from licence validity.

Official sources

Learner and gearbox conditions ; Road Rules 2019, rule 373 ; official handbook, Chapter 1 . Sources checked 10 October 2026.