Study guide

8.2 Wheels, Tyres, Lights and Rear Marking Plates

Tasmania Heavy Vehicle Knowledge Test — Free Study Guide 2026 Exam

Track your progress as you read

Finished sections get a check mark.

1 1. Licence Classes and the Knowledge Test

1.1 Choosing LR, MR, HR, HC or MC 1.2 Eligibility and Assessment Pathways 1.3 Learner, Provisional and Gearbox Conditions 1.4 Test Administration and Licence Recognition

2 2. Fitness, Alcohol, Drugs and Fatigue

2.1 Medical Fitness, Seatbelts and Safe Cab Access 2.2 Alcohol Rules and Breath Testing 2.3 Drugs, Medicines and Driving 2.4 Recognising and Managing Fatigue

3 3. Work, Rest and Transport Responsibilities

3.1 Standard Hours and Approved Alternative Hours 3.2 Work Diaries, Records and Chain of Responsibility

4 4. Observation, Space and Vehicle Control

4.1 Observation, Road Position and Hazard Planning 4.2 Following Gaps, Separation and Stopping Distance 4.3 Brake Failure, Skids and Combination Stability 4.4 Hills, Curves, Weather and Animals

5 5. Heavy Vehicle Signs and Manoeuvres

5.1 Clearance, Load, Entry and Route Restrictions 5.2 Turning, Lane Position and Turning Signs 5.3 Speed Caps, Overtaking, Lane Changes and Reversing 5.4 Bus Rules and Heavy or Long Vehicle Parking

6 6. Breakdowns, Warning Triangles and Fire

6.1 Breakdown Safety and Warning Triangles 6.2 Vehicle Fire and Emergency Assistance

7 7. General Tasmanian Traffic Rules

7.1 Signs, Signals and Intersection Priority 7.2 Roundabouts, Merging and Road Markings 7.3 Railway and Pedestrian Crossings 7.4 Speed Zones, School Buses, Cyclists and Emergency Vehicles 7.5 Parking, Distraction, Restraints and Crash Duties

8 8. Roadworthiness, Brakes and Transmission

8.1 Pre-departure Checks and Maintenance Reports 8.2 Wheels, Tyres, Lights and Rear Marking Plates 8.3 Air Brake Architecture, Parking Brakes and ABS 8.4 Handbook Brake Tests and Fault Decisions 8.5 Gearboxes, Double-declutching and Auxiliary Brakes

9 9. Coupling and Uncoupling

9.1 Prime Mover and Semi-trailer Procedures 9.2 Truck-and-trailer Connections and Final Checks

10 10. Dimensions, Mass and Load Distribution

10.1 Dimensions, Rear Overhang and Projecting Loads 10.2 Ratings, Current Axle Limits and Distribution

11 11. Restraint Principles and Equipment

11.1 Performance Standards and Restraint Methods 11.2 Blocking, Dunnage, Containers, Pipes and Lashings

12 12. Dangerous Goods

12.1 Licensing, Identification and Incident Risks

13 13. Oversize Access and Permits

13.1 Notice Eligibility, Permits and Route Conditions

14 14. Traffic Offences and Licence Consequences

14.1 Demerit Points, Speeding and Other Offences

15 15. Inspections, Defects, Noise and Smoke

15.1 Checking Stations and Return to Roadworthy Use

8.2 Wheels, Tyres, Lights and Rear Marking Plates

Key Takeaways Explain This Topic AI

The tyre requirement is at least 1.5 mm in principal grooves around the circumference across the prescribed tread band; it is not a requirement for every decorative shoulder groove.

Check tyre inflation, cuts, bulges, dual clearance, rim damage and the correct number and type of wheel fasteners.

Rear marking plates generally apply to motor vehicles above 12 t and trailers above 10 t GTM, with specified exemptions such as relevant urban route buses.

Last updated: October 2026

Check tyres for more than tread

Tyres provide the contact through which steering, braking and drive forces reach the road. A tyre with adequate tread can still be unsafe because of a bulge, exposed material, unsuitable rating or incorrect inflation. Inspect each tyre on every vehicle unit, including inner duals that are easy to overlook. A spare must also be suitable and secured.

The National Heavy Vehicle Inspection Manual describes the 1.5 mm minimum in principal grooves, in a continuous band around the circumference extending across at least 75% of tread width. Principal grooves include the main grooves with tread-wear indicators. Do not turn this into a demand that every shallow shoulder feature has 1.5 mm, but do inspect the whole tyre for damage and other rejection conditions.

Inflation, matching and damage

Use the manufacturer’s pressure guidance for the tyre, load and vehicle, and check using the appropriate conditions and equipment. Do not guess a universal truck pressure. Underinflation can increase flexing and heat; overinflation can affect contact and behaviour. A tyre that repeatedly loses pressure needs investigation rather than repeated inflation as a permanent fix.

Check cuts, bulges, exposed cords, uneven wear and foreign objects. Dual tyres must have appropriate clearance and compatibility so they do not rub or overload one tyre. Remove the vehicle from service or obtain assessment when unsafe damage is found. Do not crawl between wheels or disturb a loaded assembly without the safe procedure.

  • Item Look for Why it matters
  • Tread Principal-groove depth and uneven wear Grip and signs of underlying faults
  • Sidewall Cuts, bulges or exposed material Potential structural failure
  • Dual pair Contact, trapped objects and unsuitable matching Heat, damage and uneven load sharing
  • Rim Cracks, distortion or damage Wheel integrity
  • Fasteners Correct nuts/studs, looseness and rust trails Wheel attachment
  • Valve and inflation Leakage and correct pressure Stable tyre operation

Retreaded or regrooved tyres are not universally banned on every heavy vehicle steering axle. The actual standards, tyre markings, condition and operation determine suitability. Regrooving requires a tyre designed and marked for that purpose and the applicable standard. A driver should not cut grooves into an unsuitable tyre to make it appear compliant.

Wheel security

Wheels must have the correct number and type of nuts and studs and be properly attached. Cracked or bent rims require attention. Rust trails, movement marks or unusual fastener positions can be clues to looseness. Wheel-nut indicators are aids; their colour or angle is not a universal statutory inspection rule. An unchanged indicator does not prove every attachment is sound.

Follow the manufacturer’s and workshop’s tightening and recheck procedures. Do not use an improvised universal torque value or attempt unsafe work on split-rim or pressurised wheel assemblies. Such assemblies can be hazardous and require trained personnel and suitable equipment. Report vibration, unusual noise or steering changes promptly during the trip.

Lights and reflectors

Check high and low beam, indicators, stop lamps, tail lamps, clearance and marker lamps, number-plate illumination and any applicable reversing, fog or school warning lights. Required lamps and reflectors must work, be secure and have sound lenses. Cargo, dirt and accessories must not obscure them. Check the trailer as well as the truck.

Lights communicate the vehicle’s presence, width and intentions. A failed stop lamp can leave following traffic unaware of braking; a missing side marker can make a long trailer difficult to judge at night. Repair faults through the appropriate process rather than rely on hand signals for normal freight operation.

Flashing warning lights are restricted by colour, vehicle category and circumstances. Amber or yellow is associated with specified special-use warnings; red, blue and other emergency combinations have controlled uses. Fitting a beacon does not create emergency priority or make every roadside activity a 40 km/h scene. Verify that the vehicle and use are authorised, and maintain the required visibility.

Rear marking plates

Retroreflective rear marking plates help other road users recognise a heavy vehicle. The handbook generally requires them on motor vehicles above 12 t GVM and trailers above 10 t GTM, and describes additional combination situations. Specified exemptions include relevant route buses used only in urban areas. Check current Vehicle Standards Bulletin 12 for the exact vehicle, approved material, placement and replacement rules.

Keep plates clean, secure, visible and undamaged. Do not paint over them, obscure them with equipment or replace them with an unapproved decorative panel. Modern replacement requirements specify approved reflective classes; an obsolete plate illustration is not permission to fit any old material.

The DO NOT OVERTAKE TURNING VEHICLE sign concerns a qualifying vehicle at least 7.5 m long and its turning rules. Rear plates concern conspicuity and vehicle standards. One may incorporate the wording when suitable, but neither automatically supplies the legal effect of the other.

Key decisions

Inspect every tyre and wheel, confirm all required lights and markings, and use the correct standards for the actual vehicle. Visible accessories support safety only when properly fitted and maintained.

Official sources

NHVR Inspection Manual, wheels, tyres and hubs ; Vehicle Standards Bulletin 12 ; handbook lights and plates . Sources checked 10 October 2026.