Study guide
Coupling and Uncoupling: Procedures, Air Lines, Trailer Park Brake, Roll-Away Confirmation, and HC Licence Threshold
VicRoads Heavy Vehicle Knowledge Test — Rigid KT4
Track your progress as you read
Finished sections get a check mark.
1 Victorian Road Rules — Driver Obligations
Speed Limits for Heavy Vehicles in Victoria Zero BAC and Roadside Drug Testing for Heavy Vehicle Drivers Seatbelts, Parking Restrictions, and Night-Time Clearance Lighting Railway Crossing Procedures for Buses and Heavy Vehicles
2 Victorian Road Rules — Road Situations and Chain of Responsibility
Portable Warning Triangles: Carriage, Placement, and AS 3790 Following Distances, Lane Changes, and Turn Procedures for Long Vehicles Chain of Responsibility, Weighbridge Stops, and Enforcement Powers
3 Heavy Vehicle Law, Dimensions, and Access
Heavy Vehicle Licence Classes and Transmission Restrictions Mass and Dimension Limits for Rigid Vehicles Heavy Vehicle Road Signs, Access Restrictions, and Oversize/Overmass Permits
4 Vehicle Inspections and Roadworthiness
Pre-Operational Daily Checks: Cabin, Engine, Tyres, Brakes, and Lights Air Brake vs Hydraulic Brake System Checks and After-Departure Inspection Defect Identification, Roadworthiness Obligations, and Regular Mechanical Inspections
5 Vehicle Control, Braking, and Gear Selection
Double-Clutching and Gear Selection for Non-Synchromesh Gearboxes Braking Systems, Brake Fade, Stopping Distances, and Air Brake Delay Off-Tracking, Rollover Risk, Crash Avoidance Space, and Skid Correction
6 Load Restraint and Load Rules
6.1 Load Restraint Performance Standards 6.2 Tie-down vs Direct Restraint Methods 6.3 Load Placement, Distribution, Overhang Limits, and Load Security Checks
7 Fatigue Management and Work Diary
Standard Hours, BFM, AFM and ACH: Work/Rest Options and Fatigue-Regulated Vehicles National Driver Work Diary: Requirements, Completion, Record-Keeping, and Fatigue Prevention
8 Coupling and Combination Vehicle Rules
Coupling and Uncoupling: Procedures, Air Lines, Trailer Park Brake, Roll-Away Confirmation, and HC Licence Threshold
Coupling and Uncoupling: Procedures, Air Lines, Trailer Park Brake, Roll-Away Confirmation, and HC Licence Threshold
Key Takeaways Explain This Topic AI
Connect the air lines correctly, matching the colours at both ends, and support them so they will not be crushed when you reverse; on a trailer without spring brakes, connect them first so you can use the trailer brakes while you finish coupling.
Always apply the trailer park brake (spring brakes) and lower the landing legs before uncoupling — skipping either causes the trailer to roll away.
The roll-away confirmation test checks that the coupling is locked by gently attempting to drive forward against the trailer brakes before raising the landing legs.
You need an HC (Heavy Combination) licence when the trailer's GVM exceeds 9 tonnes — a 9.5 t trailer behind a 15 t rigid truck triggers the HC threshold.
Crossing the red and yellow air lines prevents the spring brakes from releasing and can lock the trailer wheels; always match colours at both ends.
Last updated: October 2026
Coupling and Uncoupling: Procedures, Air Lines, Trailer Park Brake, Roll-Away Confirmation, and HC Licence Threshold
Quick Answer: When coupling, make sure the trailer is held by its brakes or chocks and the air lines are connected correctly (on a trailer without spring brakes, before you finish coupling); reverse until the coupling locks, perform a roll-away test by gently pulling forward against the locked trailer brakes while the landing legs still support the trailer, visually check the coupling, then connect the electrical cable and wind up the landing legs. When uncoupling, apply the trailer brakes, lower the landing legs, disconnect the air lines and electrical cable, release the coupling, and drive clear. You need an HC licence whenever the trailer's GVM exceeds 9 tonnes.
The coupling and uncoupling sequence is safety-critical: a trailer that rolls away after uncoupling can kill, and a crossed air line can lock a trailer's wheels at speed. The procedures below follow accepted Victorian heavy vehicle training standards and NHVR guidance under the Heavy Vehicle National Law (HVNL).
Air Line Colour Coding
Combination vehicles use a dual-line air system. Colour coding is standardised — the same colour connects on both the towing vehicle and the trailer, and you must never cross them.
Line Colour Function
Emergency / supply Red Continuously charges the trailer's air tanks and holds the spring (park) brakes OFF while pressurised; when disconnected or depleted, spring brakes apply automatically (fail-safe)
Service Yellow Carries the brake pedal signal from the towing vehicle to the trailer's service brake chambers during normal braking
Mnemonic: Red = Release (supply pressure releases the spring brakes), Yellow = your foot (service line applies brakes when you press the pedal). If the red line is connected and pressurised but the trailer wheels stay locked, you have crossed the lines or the trailer air system has a fault — do not drive.
Coupling Sequence
Inspect the coupling — check the fifth wheel skid plate (or pintle hook and eye) for cracks; confirm the jaw/lock mechanism is clean, greased, and operates freely and the kingpin or drawbar eye is not worn.
Position the vehicle — align straight and square behind the trailer on level ground; do not couple on a slope.
Reverse slowly — back until the fifth wheel jaw closes and locks over the kingpin (or the pintle eye seats in the hook); verify the jaw lock indicator is fully engaged.
Confirm the coupling is locked — attempt to pull forward gently in a low gear; if it holds, the coupling is locked (first stage of the roll-away confirmation).
Connect the air lines — connect them correctly and properly, matching colours at both ends, and keep them supported so they cannot be crushed. The handbook gives no fixed order for the individual lines; on a trailer without spring brakes, connect the air lines before you finish coupling so you can use the trailer brakes (and leave the electrical cable until the coupling is confirmed, because it could be torn out if the vehicle rolls forward).
Perform the roll-away confirmation test — apply the trailer brakes via the service pedal or trailer brake control, release the vehicle's park brake, and attempt to move forward gently against the locked trailer. The combination should not move. Do this while the landing legs still support the trailer; it confirms the coupling is secure and the trailer brakes work.
Visually inspect the coupling — jaws engaged on the shaft (not the head) of the king pin, no gap between the turntable halves, locking lever locked and safety catch in place.
Connect the electrical cable and any safety chains or breakaway connections.
Raise the landing legs — wind fully up, stow the handle, confirm the legs clear the road.
Check lights, reflectors, and mirrors — confirm trailer brake, indicator, tail, and clearance lights operate; adjust mirrors for the combination length.
Uncoupling Sequence
Park on level ground , apply the towing vehicle's park brake, and chock the trailer wheels if the ground has any slope.
Apply the trailer park brake (spring brakes) so the trailer is held by its own brakes, not the towing vehicle.
Lower the landing legs until the pads are firmly on the ground and the trailer's weight is on the legs, not the coupling. Wind a little further to lift the coupling slightly so the jaw is not under load.
Disconnect the air lines. On a prime mover, the handbook first sets the protection valve to "emergency", which cuts off air to the trailer and, if the trailer has spring brakes, puts them on.
Disconnect the electrical cable and stow it; release any safety chains.
Release the fifth wheel jaw (or open the pintle hook) and confirm it is fully open.
Pull the towing vehicle forward slowly and clear of the trailer; watch in the mirror that the trailer stays stationary.
Stow the air lines and landing-leg handle in their brackets.
Common Traps
Forgetting the trailer park brake — the single most common cause of a runaway trailer. Uncouple with only the towing vehicle's park brake and the legs down, and the trailer is held by nothing once you pull clear. Always apply the trailer's spring brakes first.
Crossing the air lines — connecting the red line to the yellow fitting (or vice versa) prevents supply pressure reaching the parking-brake release circuit; the trailer wheels stay locked or the service line never signals the brakes. Match colours at both ends every time.
Raising the landing legs before the roll-away test — if the coupling is not actually locked and the legs are already up, the trailer can drop onto the skid plate or roll. Do the pull-forward test while the legs still support the front of the trailer.
Uncoupling on a slope — even with spring brakes on, a trailer on a slope can creep if the legs sink or the brake is partially failed. Pick level ground or chock the wheels.
HC Licence Threshold
A Victorian Heavy Rigid (HR) licence lets you drive a rigid vehicle over 8 t GVM and tow a trailer, but only up to a limit. Once the trailer's GVM exceeds 9 tonnes , the combination becomes a Heavy Combination (HC) and an HC licence is required.
The rule: if the trailer GVM is more than 9 tonnes, you need an HC licence . Below that threshold, an HR licence covers a rigid vehicle towing a single trailer other than a semi-trailer (for example a dog trailer); it does not cover a prime mover towing a semi-trailer.
Worked Example
You hold an HR licence and are asked to drive a rigid truck (GVM 15 t) towing a tipper trailer (GVM 9.5 t). The trailer GVM (9.5 t) is greater than 9 t, so the combination is a Heavy Combination. You cannot legally drive it on an HR licence — you need an HC licence. If the same truck towed a single trailer (not a semi-trailer) with a GVM of 8.5 t, the combination falls under the HR class and your licence covers it, provided the truck's GCM rating is not exceeded.
Transport Victoria is clear: you can only drive vehicles in the category for which you are licensed, or vehicles in lesser categories.