Study guide
Standard Hours, BFM, AFM and ACH: Work/Rest Options and Fatigue-Regulated Vehicles
VicRoads Heavy Vehicle Knowledge Test — Rigid KT4
Track your progress as you read
Finished sections get a check mark.
1 Victorian Road Rules — Driver Obligations
Speed Limits for Heavy Vehicles in Victoria Zero BAC and Roadside Drug Testing for Heavy Vehicle Drivers Seatbelts, Parking Restrictions, and Night-Time Clearance Lighting Railway Crossing Procedures for Buses and Heavy Vehicles
2 Victorian Road Rules — Road Situations and Chain of Responsibility
Portable Warning Triangles: Carriage, Placement, and AS 3790 Following Distances, Lane Changes, and Turn Procedures for Long Vehicles Chain of Responsibility, Weighbridge Stops, and Enforcement Powers
3 Heavy Vehicle Law, Dimensions, and Access
Heavy Vehicle Licence Classes and Transmission Restrictions Mass and Dimension Limits for Rigid Vehicles Heavy Vehicle Road Signs, Access Restrictions, and Oversize/Overmass Permits
4 Vehicle Inspections and Roadworthiness
Pre-Operational Daily Checks: Cabin, Engine, Tyres, Brakes, and Lights Air Brake vs Hydraulic Brake System Checks and After-Departure Inspection Defect Identification, Roadworthiness Obligations, and Regular Mechanical Inspections
5 Vehicle Control, Braking, and Gear Selection
Double-Clutching and Gear Selection for Non-Synchromesh Gearboxes Braking Systems, Brake Fade, Stopping Distances, and Air Brake Delay Off-Tracking, Rollover Risk, Crash Avoidance Space, and Skid Correction
6 Load Restraint and Load Rules
6.1 Load Restraint Performance Standards 6.2 Tie-down vs Direct Restraint Methods 6.3 Load Placement, Distribution, Overhang Limits, and Load Security Checks
7 Fatigue Management and Work Diary
Standard Hours, BFM, AFM and ACH: Work/Rest Options and Fatigue-Regulated Vehicles National Driver Work Diary: Requirements, Completion, Record-Keeping, and Fatigue Prevention
8 Coupling and Combination Vehicle Rules
Coupling and Uncoupling: Procedures, Air Lines, Trailer Park Brake, Roll-Away Confirmation, and HC Licence Threshold
Standard Hours, BFM, AFM and ACH: Work/Rest Options and Fatigue-Regulated Vehicles
Key Takeaways Explain This Topic AI
A fatigue-regulated heavy vehicle has a GVM over 12 tonnes, or a bus with GVM over 4.5t carrying more than 12 adults (including the driver)
Standard Hours solo drivers may work max 12h in 24h and 72h in 7 days, with sub-period limits of 5.25h/5.5h, 7.5h/8h, and 10h/11h
BFM (up to 14h work in 24h) and AFM were accreditation modules before 1 August 2026; existing accreditations continue until they expire, and new applicants now use ACA–Fatigue (Alternative Compliance Hours).
AFM and ACH hours are not a fixed table: they are stated on the operator's accreditation certificate, and drivers must carry a copy in the vehicle.
Changing from Standard Hours or BFM needs full compliance with the new option or a 48-hour reset rest; changing from AFM, ACH or exemption hours needs a 48-hour reset rest (or the amount on the certificate) and compliance with the new option.
Last updated: October 2026
What Makes a Heavy Vehicle Fatigue-Regulated?
Under the Heavy Vehicle National Law (HVNL), fatigue management rules apply only to fatigue-regulated heavy vehicles . A vehicle is fatigue-regulated if it meets any of these criteria:
- A motor vehicle with a Gross Vehicle Mass (GVM) over 12 tonnes
- A combination where the total GVM or Gross Combination Mass (GCM) exceeds 12 tonnes
- A bus with a GVM over 4.5 tonnes fitted to carry more than 12 adults (including the driver)
- A truck, or combination including a truck, with a GVM over 12 tonnes with a machine or implement attached
If you drive a Heavy Rigid vehicle with a GVM above 12 tonnes, the work and rest hours rules apply every time you drive it. Separately, since 1 August 2026 the duty not to drive while impaired by fatigue or unfit to drive applies to every heavy vehicle over 4.5 tonnes, fatigue-regulated or not. These rules are enforced by the National Heavy Vehicle Regulator (NHVR) and authorised officers including Victoria Police and Transport Safety Services.
Standard Hours: The Default Work/Rest Framework
Standard Hours is the default set of work and rest limits. No accreditation is needed — every fatigue-regulated driver operates under Standard Hours unless working under BFM, AFM, ACH or exemption hours.
For a solo driver (no second driver), the Standard Hours limits are:
- In any period of Maximum work time Minimum rest time
- 5.5 hours 5.25 hours (5 and a quarter hours) 15 continuous minutes
- 8 hours 7.5 hours (7 and a half hours) 30 minutes (in 15-min blocks)
- 11 hours 10 hours 60 minutes (in 15-min blocks)
- 24 hours 12 hours 7 continuous hours stationary rest
- 7 days (168 hours) 72 hours 24 continuous hours stationary rest
- 14 days (336 hours) 144 hours 4 night rest breaks, 2 of them on consecutive days
The sub-period limits (5.25h/5.5h, 7.5h/8h, 10h/11h) are rolling maximums counted forward from the end of the last rest break. Within any 5.5-hour window, you may work up to 5.25 hours and must take at least 15 minutes continuous rest. Within any 8-hour window, up to 7.5 hours of work is allowed with at least 30 minutes rest in 15-minute blocks. Within any 11-hour window, up to 10 hours work is allowed with at least 60 minutes rest.
A night rest break is 7 continuous hours of stationary rest taken between 10 pm on one day and 8 am on the next day (using the time zone of the driver's base), or a 24 continuous hours stationary rest break.
Stationary rest means the driver is out of the heavy vehicle, or resting in an approved sleeper berth of a stationary vehicle. This is different from continuous rest, which can include time resting as a passenger in a moving vehicle.
Basic Fatigue Management (BFM)
Basic Fatigue Management (BFM) was an accreditation module of the National Heavy Vehicle Accreditation Scheme (NHVAS) under the HVNL before 1 August 2026 . Operators who already hold BFM accreditation may keep operating under it until it expires, is cancelled, or they transition to the new Heavy Vehicle Accreditation scheme. BFM allows drivers up to 14 hours of work in a 24-hour period — two extra hours compared to Standard Hours.
BFM solo driver limits include:
- 24 hours: max 14 hours work, minimum 7 continuous hours stationary rest
- 7 days: max 36 hours long/night work time
14 days: max 144 hours work, with two 24-hour continuous stationary rest breaks (one taken after no more than 84 hours work) and 4 night rest breaks, 2 of them on consecutive days
BFM also has its own sub-period limits: 6 hours work in 6.25 hours, 8.5 hours in 9 hours, and 11 hours in 12 hours, each with the same 15-minute block rest minimums.
Advanced Fatigue Management (AFM)
Advanced Fatigue Management (AFM) was also an NHVAS accreditation module before 1 August 2026. Its maximum work and minimum rest times are set out on the operator's AFM accreditation certificate, which drivers must carry in the vehicle. Existing AFM accreditations continue until they expire, are cancelled, or the operator transitions.
Alternative Compliance Hours (ACH)
From 1 August 2026, Alternative Compliance Hours (ACH) are the work and rest hours available through Alternative Compliance Accreditation–Fatigue (ACA–Fatigue) under the new Heavy Vehicle Accreditation scheme. ACH replaces the BFM and AFM accreditation pathway for new applicants. The hours are stated on the operator's ACA–Fatigue certificate, drivers must carry a copy in the vehicle, and a driver cannot self-select ACH unless the operator holds the accreditation.
Switching Between Options
You may operate under only one work and rest hours option at a time. When changing options, the NHVR rules are:
From Standard Hours or BFM: fully comply with the maximum work and minimum rest requirements of the new option, OR take a reset rest break of at least 48 continuous hours
From AFM, ACH or exemption hours: take a reset rest break of at least 48 continuous hours (or the reset rest stated on the certificate, permit or notice), AND comply with all other requirements of the new option
The 48-hour reset ensures accumulated fatigue under the more flexible option does not carry over into the stricter framework.
Comparison: Standard Hours vs BFM vs AFM
- Feature Standard Hours BFM (existing accreditations) AFM (existing accreditations)
- Max work / 24h 12 hours 14 hours On the AFM certificate
- Max work / 7 days 72 hours 36 hours long/night work (14-day cycle: 144 hours) On the AFM certificate
- Min rest / 24h 7h continuous stationary 7h continuous stationary On the AFM certificate
- Sub-period limits 5.25h/5.5h, 7.5h/8h, 10h/11h 6h/6.25h, 8.5h/9h, 11h/12h On the AFM certificate
Accreditation required No NHVAS BFM (closed to new applicants from 1 Aug 2026) NHVAS AFM (closed to new applicants from 1 Aug 2026)
Work diary 100+ km from base Always (any distance) Always (any distance)
Changing to another option 48h reset rest OR comply 48h reset rest OR comply 48h reset rest (or certificate amount) AND comply