Study guide

Heavy Vehicle Road Signs, Access Restrictions, and Oversize/Overmass Permits

VicRoads Heavy Vehicle Knowledge Test — Rigid KT4

Track your progress as you read

Finished sections get a check mark.

1 Victorian Road Rules — Driver Obligations

Speed Limits for Heavy Vehicles in Victoria Zero BAC and Roadside Drug Testing for Heavy Vehicle Drivers Seatbelts, Parking Restrictions, and Night-Time Clearance Lighting Railway Crossing Procedures for Buses and Heavy Vehicles

2 Victorian Road Rules — Road Situations and Chain of Responsibility

Portable Warning Triangles: Carriage, Placement, and AS 3790 Following Distances, Lane Changes, and Turn Procedures for Long Vehicles Chain of Responsibility, Weighbridge Stops, and Enforcement Powers

3 Heavy Vehicle Law, Dimensions, and Access

Heavy Vehicle Licence Classes and Transmission Restrictions Mass and Dimension Limits for Rigid Vehicles Heavy Vehicle Road Signs, Access Restrictions, and Oversize/Overmass Permits

4 Vehicle Inspections and Roadworthiness

Pre-Operational Daily Checks: Cabin, Engine, Tyres, Brakes, and Lights Air Brake vs Hydraulic Brake System Checks and After-Departure Inspection Defect Identification, Roadworthiness Obligations, and Regular Mechanical Inspections

5 Vehicle Control, Braking, and Gear Selection

Double-Clutching and Gear Selection for Non-Synchromesh Gearboxes Braking Systems, Brake Fade, Stopping Distances, and Air Brake Delay Off-Tracking, Rollover Risk, Crash Avoidance Space, and Skid Correction

6 Load Restraint and Load Rules

6.1 Load Restraint Performance Standards 6.2 Tie-down vs Direct Restraint Methods 6.3 Load Placement, Distribution, Overhang Limits, and Load Security Checks

7 Fatigue Management and Work Diary

Standard Hours, BFM, AFM and ACH: Work/Rest Options and Fatigue-Regulated Vehicles National Driver Work Diary: Requirements, Completion, Record-Keeping, and Fatigue Prevention

8 Coupling and Combination Vehicle Rules

Coupling and Uncoupling: Procedures, Air Lines, Trailer Park Brake, Roll-Away Confirmation, and HC Licence Threshold

Heavy Vehicle Road Signs, Access Restrictions, and Oversize/Overmass Permits

Key Takeaways Explain This Topic AI

A 'No Trucks' sign with no mass shown bans goods-carrying vehicles over 4.5 t GVM unless an exception applies (for example, unloading beyond the sign with no other route); with a mass shown it bans vehicles whose GVM is more than that mass.

The handbook says you must not pass a load limit sign if your vehicle's GVM, or axle group mass, is more than the sign allows.

Bus Give Way and Bus Lane signs restrict heavy vehicle behaviour near buses; Bus Give Way requires a driver in the left lane in a built-up area to give way to a bus ahead that displays a 'Give Way to Buses' sign and is signalling right to re-enter that lane (r. 77).

Oversize/overmass loads exceeding the general-access dimensions or mass limits require a permit from the NHVR (or VicRoads for state-only roads); permits specify the route, travel times, signs, flags, and pilot/escort requirements.

Low-clearance signs ('Low Clearance 4.0 m') and automatic clearance gauges warn drivers of overhead height restrictions; an overheight vehicle that strikes a structure commits an offence and causes severe damage, so route planning must confirm bridge and wire heights against the loaded vehicle height.

Last updated: October 2026

Heavy vehicle road signs you must recognise

The Victorian road network uses a specific set of regulatory and warning signs aimed at heavy vehicles. The HR knowledge test asks you to identify what each sign requires or prohibits, so recognise the symbol and the legal effect.

No Trucks

The No Trucks sign is a red-ring prohibition sign showing a truck symbol. Under rule 104 of Victoria's Road Safety Road Rules:

No mass or length shown: the driver of a truck must not drive past it. The handbook puts it this way: "No goods-carrying vehicle over 4.5 tonnes GVM can pass this sign" without a permit, unless an exemption applies.

A mass shown (e.g., 12 t): a driver must not pass if the GVM of the vehicle (or of any vehicle in the combination) is more than that mass. A length can be shown in the same way.

A truck may still pass when its destination for loading or unloading lies beyond the sign and there is no other route (or every other route passes another No Trucks sign), when the sign applies only to certain lanes and the truck uses another lane, when it is escorted by police or an authorised officer, or under a permit or written exemption. Buses are covered by a separate No Buses sign.

Trucks Must Enter

The Trucks Must Enter sign (a white panel with a black truck symbol and an arrow) directs trucks to take a specific action — typically to enter a specified side road, slip lane, or rest area. Where the sign is placed before a junction it obliges trucks to use the indicated route; ignoring it is an offence. Closely related are Trucks Use Low Gear signs on descents and Trucks Use Left Lane signs on multi-lane roads.

Load limit signs

Load limit signs may apply to bridges or sections of road. The handbook's rule is: you must not pass the sign if the Gross Vehicle Mass (GVM), or axle group mass, of your vehicle is more than that allowed by the sign. Bridge load limit signs come in a gross mass version and a mass-per-axle-group version.

If you are unsure whether your vehicle is within the limit, treat the sign as applying to you and find an alternative route. Fines are heavy, and you might also have to pay for damage to roads that cannot take the weight of your vehicle.

Bus Give Way and Bus Lane

Under Victorian road rules (Road Safety Road Rules 2017):

Bus Give Way : in a built-up area, if you are in the left lane or left line of traffic, you must give way to a bus ahead that displays a 'Give Way to Buses' sign, has its right indicator on and is about to re-enter your lane from the side of the road, a shoulder or a bus-stop bay (r. 77). This rule applies to all drivers including heavy vehicle drivers; failing to give way is an offence.

Bus Lane : a lane marked with a 'Bus Lane' sign and a white diamond or 'B' lane marking is reserved for buses (and sometimes bicycles) during the times shown. Trucks must not travel or stop in a bus lane during its hours of operation unless signage permits.

Bus Zone / Taxi Zone signs: trucks must not stop in these zones, even briefly, outside permitted hours.

Truck lane and route restrictions

On some three-lane and four-lane freeways in Victoria, a truck lane restriction sign bans vehicles over 4.5 t GVM from the right-hand lane wherever it is displayed, 24 hours a day. Transport Victoria lists the exceptions as buses, emergency vehicles, and vehicles under escort by police or an authorised officer (the handbook also mentions caravans). There is no statewide right-lane ban without a sign. Separately, on a multi-lane road with a speed limit over 80 km/h, or a road signed "Keep Left Unless Overtaking", you must keep left unless overtaking — and a Truck Lane sign only stops other vehicles using that lane; it does not require trucks to use it.

Oversize and overmass permits

A vehicle or load that exceeds any general-access dimension (4.3 m height, 2.5 m width, 12.5 m length) or any general mass limit becomes an overdimensional (OD) or overmass (OM) load. Operating such a vehicle on a public road without a permit is an offence under the HVNL.

Permits are issued by:

The National Heavy Vehicle Regulator (NHVR) for travel that crosses state borders or uses the national network (most Victorian permits for OS/OM loads are NHVR permits under the Class 1 or Class 3 permit framework).

VicRoads for some state-only access, bridge, and route approvals where the national framework does not apply.

A typical OS/OM permit specifies:

The vehicle and load description (dimensions, mass, axle count).

The approved route — you may not deviate from the mapped route.

Travel times — often restricted to daylight hours, and may exclude weekends, public holidays, or peak periods.

Pilot/escort vehicle requirements (see below).

Signs and flags — "OVERSIZE" signs front and rear, corner flags on projections, rotating amber warning lights.

Speed limits — often below the posted limit for stability and braking.

OD routes, low-clearance signs, and automatic clearance gauges

Approved routes for OS/OM loads are called OD routes . The NHVR publishes route maps; VicRoads supplements with state-level approvals. Drivers must plan the entire route from origin to destination before departure, including any turning paths, bridge mass ratings, and overhead clearances.

Low-clearance signs are warning signs showing the available height under a structure (e.g., "Low Clearance 4.0 m"). Drivers must compare the loaded vehicle height against the sign. The handbook says that if your vehicle is the height shown on the sign or higher , you must not drive under it — find an alternative route.

Automatic clearance gauges are physical height-checking frames (sometimes laser-based) installed before low bridges, tunnels, and some carparks. They detect an overheight vehicle and trigger warning signs, flashing lights, or barriers. If a gauge triggers as you approach, stop and reassess — do not proceed under the structure. Automatic gauges reduce but do not eliminate bridge strikes; the driver remains responsible for verifying loaded height.

Pilot vehicles

Oversize loads above certain thresholds must be accompanied by pilot vehicles (also called escort vehicles). Pilot vehicles:

Travel ahead of (and/or behind) the OS/OM load.

Display roof-mounted 'OVERSIZE' signs and amber flashing/warning lights.

Warn oncoming traffic, control traffic at narrow points, and communicate with the OS/OM driver by radio.

Help the OS/OM driver navigate tight turns and confirm overhead clearances.

The number of pilot vehicles required scales with the load dimensions and route. A load only slightly over width may need one pilot; a very wide or long load may need two pilots plus a police escort. The OS/OM permit states the requirement; you may not travel with fewer pilots than the permit specifies.

Practical pre-departure checks for access

Before driving an oversize/overmass load, confirm:

The permit is current and carried in the vehicle.

The approved route matches the planned trip, with no deviations.

The vehicle's loaded dimensions and mass match the permit (an OS/OM permit is invalid if the actual load differs from what was approved).

Pilot vehicles (if required) are present, correctly signed, and able to communicate by radio.

OVERSIZE signs, flags, and amber warning lights are fitted and working.

Bridge heights and load limits on the route have been checked against the loaded vehicle.

Travel-time restrictions in the permit are observed (no travel outside approved hours).

Failure to comply with any permit condition is an offence and can void insurance and trigger Chain of Responsibility liability for the operator, scheduler, and consignor.