Study guide

Mass and Dimension Limits for Rigid Vehicles

VicRoads Heavy Vehicle Knowledge Test — Rigid KT4

Track your progress as you read

Finished sections get a check mark.

1 Victorian Road Rules — Driver Obligations

Speed Limits for Heavy Vehicles in Victoria Zero BAC and Roadside Drug Testing for Heavy Vehicle Drivers Seatbelts, Parking Restrictions, and Night-Time Clearance Lighting Railway Crossing Procedures for Buses and Heavy Vehicles

2 Victorian Road Rules — Road Situations and Chain of Responsibility

Portable Warning Triangles: Carriage, Placement, and AS 3790 Following Distances, Lane Changes, and Turn Procedures for Long Vehicles Chain of Responsibility, Weighbridge Stops, and Enforcement Powers

3 Heavy Vehicle Law, Dimensions, and Access

Heavy Vehicle Licence Classes and Transmission Restrictions Mass and Dimension Limits for Rigid Vehicles Heavy Vehicle Road Signs, Access Restrictions, and Oversize/Overmass Permits

4 Vehicle Inspections and Roadworthiness

Pre-Operational Daily Checks: Cabin, Engine, Tyres, Brakes, and Lights Air Brake vs Hydraulic Brake System Checks and After-Departure Inspection Defect Identification, Roadworthiness Obligations, and Regular Mechanical Inspections

5 Vehicle Control, Braking, and Gear Selection

Double-Clutching and Gear Selection for Non-Synchromesh Gearboxes Braking Systems, Brake Fade, Stopping Distances, and Air Brake Delay Off-Tracking, Rollover Risk, Crash Avoidance Space, and Skid Correction

6 Load Restraint and Load Rules

6.1 Load Restraint Performance Standards 6.2 Tie-down vs Direct Restraint Methods 6.3 Load Placement, Distribution, Overhang Limits, and Load Security Checks

7 Fatigue Management and Work Diary

Standard Hours, BFM, AFM and ACH: Work/Rest Options and Fatigue-Regulated Vehicles National Driver Work Diary: Requirements, Completion, Record-Keeping, and Fatigue Prevention

8 Coupling and Combination Vehicle Rules

Coupling and Uncoupling: Procedures, Air Lines, Trailer Park Brake, Roll-Away Confirmation, and HC Licence Threshold

Mass and Dimension Limits for Rigid Vehicles

Key Takeaways Explain This Topic AI

GVM (Gross Vehicle Mass) is the maximum laden mass of a single vehicle; GCM (Gross Combination Mass) is the maximum laden mass of a vehicle plus any trailer it tows — both are set by the manufacturer and shown on the vehicle's compliance plate.

General-access dimension limits for rigid vehicles are 4.3 m height, 2.5 m width (2.55 m for a Safer Freight Vehicle), and 12.5 m length; rear overhang is limited to the lesser of 3.7 m or 60 % of the wheelbase.

General Mass Limits from 1 August 2026: steer axle 6.0 t (6.5 t for a complying steer axle vehicle), single axle with dual tyres 9.0 t, tandem with dual tyres 17.0 t — and the plated GVM or GCM is still the upper cap.

Operating above the dimension or mass limits turns the vehicle into an overdimensional or overmass load, which requires a permit and may restrict routes and travel times.

Axle and axle-group limits are set in the Heavy Vehicle (Mass, Dimension and Loading) National Regulation; from 1 August 2026 the General Mass Limits rose to the former Concessional Mass Limits and CML stopped being a separate limit.

Last updated: October 2026

GVM vs GCM: the two mass figures on the compliance plate

Every heavy vehicle carries a manufacturer's compliance plate that states two upper mass limits. Knowing the difference is essential because Victorian road law, the Heavy Vehicle National Law (HVNL), and the HR knowledge test all rely on them.

Gross Vehicle Mass (GVM) — the maximum permitted total laden mass of a single vehicle , including the vehicle's own mass (tare), fuel, driver, passengers, and load. GVM is the ceiling for a rigid vehicle standing alone.

Gross Combination Mass (GCM) — the maximum permitted total laden mass of the vehicle plus any trailer(s) it is designed to tow . GCM matters once a trailer is attached.

A rigid truck plated at 22 t GVM and 30 t GCM can be loaded up to 22 t on its own axles. If it tows a dog trailer, the sum of the truck's laden mass and the trailer's laden mass must not exceed 30 t. Exceeding either figure is an offence under the HVNL — the operator, driver, and (under Chain of Responsibility) other parties can all be liable.

Dimension limits: general access for rigid vehicles

A rigid vehicle operating at or below the general-access limits may travel on most of the Victorian declared road network without a permit. Exceeding any of the following turns the vehicle into an overdimensional (OD) load requiring a permit.

Dimension General-access limit (rigid vehicle) Notes

Height 4.3 m Measured from ground level to the highest point of the vehicle or load. Bridges, overpasses, and overhead wires are the most common height hazards.

Width 2.5 m (2.55 m for a Safer Freight Vehicle) Measured across the vehicle or load; devices such as mirrors and lights are excluded. The 2.55 m limit applies only to new rigid trucks and prime movers built with the specified safety features, not trailers or buses.

Length 12.5 m A rigid truck (not a bus). A bus has a 14.5 m general-access limit.

Front projection of load 1.2 m in front of the headlights The load must not project more than 1.2 m in front of the vehicle.

Rear overhang The lesser of 3.7 m or 60 % of the wheelbase Wheelbase = distance from the centre of the front axle to the rear overhang line (usually the centre of the rear axle group).

Side projection of load 150 mm beyond the side of the vehicle Loads wider than the vehicle may need a permit and flags.

The rear overhang rule trips up many candidates. "Wheelbase" for a vehicle with a rear axle group means the distance from the front steer axle centreline to the centreline of the rear axle group (the midpoint of a tandem or tri-axle group), not to the rear-most axle. The 60 %-of-wheelbase and 3.7 m figures are alternatives: you comply if your rear overhang is within both limits, i.e., within the smaller of the two.

Example: a rigid truck with a 5.0 m wheelbase. 60 % of 5.0 m = 3.0 m. The lesser of 3.7 m and 3.0 m is 3.0 m. The rear overhang limit is therefore 3.0 m for that truck. A truck with a 7.0 m wheelbase gives 60 % = 4.2 m, but the absolute 3.7 m cap applies, so the limit is 3.7 m.

Axle mass limits: General Mass Limits from 1 August 2026

General Mass Limits (GML) in the Heavy Vehicle (Mass, Dimension and Loading) National Regulation set a maximum mass for each single axle and axle group. The 1 August 2026 amendments raised GML to the former Concessional Mass Limits and removed CML as a separate limit. Vehicles at GML can use the whole road network, subject to local signs. The NHVR's current table gives these figures for a typical rigid truck:

Steer axle : 6.0 t. A complying steer axle vehicle or a Euro VI vehicle with a single steer axle can carry 6.5 t, if it meets the conditions for that concession.

Single axle with dual tyres (a typical single drive axle): 9.0 t.

Tandem axle group with dual tyres (a typical rear tandem on a rigid truck): 17.0 t.

Tri-axle group with dual tyres (not a pig trailer): 21.0 t.

Groups fitted with narrower single tyres have lower limits, so always check the tyre configuration.

The key principle: the vehicle's plated GVM is the absolute ceiling . Even if individual axle limits would theoretically allow more, the truck may not exceed the GVM on its compliance plate. The same applies to GCM for a combination.

Why dimensions and mass are tested together

The Victorian HR test pairs mass and dimension questions because the two interact. A load that is within the GVM may still breach a dimension limit (a tall pallet inside a curtain-sider that pushes height past 4.3 m, or a long steel beam that breaches rear overhang). Conversely, a load that fits within dimensions may still breach mass limits (a short, dense load that exceeds the steer or drive axle mass). You must check both before driving.

Conversions and road-friendly suspension

Mass above GML, such as Higher Mass Limits (HML), generally needs road-friendly suspension and an access arrangement such as a notice or permit, and the NHVR says Mass Management accreditation is still needed where it is a condition of that arrangement. Concessional Mass Limits no longer exist as a separate option: the former CML weights are now GML.

Pre-trip mass check

Before driving a laden rigid vehicle you should confirm:

The sum of axle masses does not exceed each axle/axle-group limit.

The total laden mass does not exceed the vehicle's plated GVM (or GCM if towing).

The load sits within 4.3 m height, 2.5 m width, 12.5 m length, the 1.2 m front projection limit, and the rear-overhang rule.

If any limit is exceeded, an overdimensional/overmass permit is in force and the route is approved.

A weighbridge is the definitive check. Police and Transport Safety Services (TSS) officers can direct you to a weighbridge; refusal is an offence under the HVNL (covered in Chapter 2).