Study guide

6.3 Load Placement, Distribution, Overhang Limits, and Load Security Checks

VicRoads Heavy Vehicle Knowledge Test — Rigid KT4

Track your progress as you read

Finished sections get a check mark.

1 Victorian Road Rules — Driver Obligations

Speed Limits for Heavy Vehicles in Victoria Zero BAC and Roadside Drug Testing for Heavy Vehicle Drivers Seatbelts, Parking Restrictions, and Night-Time Clearance Lighting Railway Crossing Procedures for Buses and Heavy Vehicles

2 Victorian Road Rules — Road Situations and Chain of Responsibility

Portable Warning Triangles: Carriage, Placement, and AS 3790 Following Distances, Lane Changes, and Turn Procedures for Long Vehicles Chain of Responsibility, Weighbridge Stops, and Enforcement Powers

3 Heavy Vehicle Law, Dimensions, and Access

Heavy Vehicle Licence Classes and Transmission Restrictions Mass and Dimension Limits for Rigid Vehicles Heavy Vehicle Road Signs, Access Restrictions, and Oversize/Overmass Permits

4 Vehicle Inspections and Roadworthiness

Pre-Operational Daily Checks: Cabin, Engine, Tyres, Brakes, and Lights Air Brake vs Hydraulic Brake System Checks and After-Departure Inspection Defect Identification, Roadworthiness Obligations, and Regular Mechanical Inspections

5 Vehicle Control, Braking, and Gear Selection

Double-Clutching and Gear Selection for Non-Synchromesh Gearboxes Braking Systems, Brake Fade, Stopping Distances, and Air Brake Delay Off-Tracking, Rollover Risk, Crash Avoidance Space, and Skid Correction

6 Load Restraint and Load Rules

6.1 Load Restraint Performance Standards 6.2 Tie-down vs Direct Restraint Methods 6.3 Load Placement, Distribution, Overhang Limits, and Load Security Checks

7 Fatigue Management and Work Diary

Standard Hours, BFM, AFM and ACH: Work/Rest Options and Fatigue-Regulated Vehicles National Driver Work Diary: Requirements, Completion, Record-Keeping, and Fatigue Prevention

8 Coupling and Combination Vehicle Rules

Coupling and Uncoupling: Procedures, Air Lines, Trailer Park Brake, Roll-Away Confirmation, and HC Licence Threshold

6.3 Load Placement, Distribution, Overhang Limits, and Load Security Checks

Key Takeaways Explain This Topic AI

Place the load with its centre of gravity low and close to the vehicle centreline, and distribute mass evenly across the axles so that no axle exceeds its legal mass limit and the steer axle keeps enough load for steering.

Front overhang is limited to 1.2 m forward of the headlights; rear overhang is the lesser of 3.7 m or 60% of the wheelbase; a load may project no more than 150 mm past either side of the vehicle.

After loading, inspect every piece of restraint equipment — chains for stretch or cracked links, turnbuckles for thread wear, shackles for pin damage, twist locks for positive engagement, and tarpaulins for tears and loose eyelets.

Re-check the load and its tension early in the trip and at every stop — lashings bed in and relax, especially on new dunnage; the handbook's after-departure check comes after about an hour of driving.

A load projecting more than 1.2 m to the rear needs a warning flag by day and a red light at night; a load beyond the dimension limits needs a permit and may need pilot vehicles.

Last updated: October 2026

A load that is beautifully restrained can still roll the truck, overload an axle, or scrape a cyclist at a kerb if it is placed badly. Placement and distribution are tested alongside restraint because they fall under the same loading requirements (HVNL Part 4.4) and the mass and dimension limits.

Centre of gravity: low and centred

The single most important placement principle is to keep the centre of gravity (CoG) low and near the vehicle centreline . A high CoG raises rollover risk because cornering forces act on a longer lever arm from the contact patch; an off-centre CoG biases weight to one side and makes the vehicle unstable in swerves and on cross-fall roads. Practical placement rules:

Place heavy items at the bottom of the stack and light items on top.

Stack items so that the combined CoG sits as close to the longitudinal centreline of the vehicle as possible — for asymmetrical loads, counterbalance rather than pile to one side.

Where possible, place dense items over or just ahead of the drive axle group, where the chassis is strongest and the mass is carried by the suspension designed for it.

Avoid loading the rear overhang with heavy items — mass behind the rear axle group unloads the steer axle and reduces steering control, and it magnifies the vertical bounce of overhanging mass.

Axle mass distribution

Mass must be distributed so that no axle exceeds its legal mass limit and the steer axle retains enough loading for steering. Key General Mass Limits for a heavy rigid vehicle (NHVR table, from 1 August 2026):

Steer axle: 6.0 t (6.5 t for a complying steer axle vehicle).

Single axle with dual tyres (typical single drive axle): 9.0 t.

Tandem axle group with dual tyres: 17.0 t.

GVM: the manufacturer's plated gross vehicle mass — the sum of all axle loads must not exceed it.

A poorly distributed load can put a vehicle over an axle limit even when the total mass is under GVM. Load forward of the drive axle adds to the steer axle; load behind the rear axle subtracts from it. The aim is an even spread that keeps every axle within its limit and leaves the steer axle with enough load for positive steering.

Overhang limits

Beyond the loaded mass, the dimensions of the load are capped by the HVNL dimension limits. Projecting loads are allowed within strict overhang limits; beyond them the load is over-dimension and requires a permit, flags and often pilot vehicles.

Direction Overhang limit Rule

Front 1.2 m forward of the headlights No load may project more than 1.2 m forward of the front of the vehicle (measured from the headlight line). Beyond that the load is over-dimension.

Rear Lesser of 3.7 m or 60% of the wheelbase Rear overhang is the lesser of 3.7 m or 60% of the wheelbase (front axle to the rear overhang line, usually the centre of the rear axle group).

Side 150 mm beyond the outermost width of the vehicle A load may project up to 150 mm past either side of the vehicle, but the total width (vehicle + projection) must not exceed the 2.5 m general width limit.

Note the rear overhang is the tighter of two tests — you take the smaller of 3.7 m and 60% of wheelbase, not the larger. A rigid truck with a 5 m wheelbase has a 60% value of 3 m, so its rear overhang limit is 3 m, not 3.7 m. This is a classic exam trap.

A load that projects more than 1.2 m to the rear must carry a warning device: in daytime a brightly coloured flag or piece of material with each side at least 300 mm long, and at night a red light that can be seen from at least 200 m (handbook). Any load beyond the dimension limits is over-dimension: it needs a permit, may need pilot vehicles, and must stick to the approved route.

Pre-departure load security checks

Before driving off, walk around the load and inspect every component of the restraint system. Restraint equipment fails in serviceable-looking ways — the defect is often invisible until you look closely.

Chains

Look for stretched, bent or cracked links — stretch indicates the chain has been overloaded; cracked links are immediate withdrawal-from-service defects.

Check the lashing capacity stamp is legible; if you cannot read the LC, you cannot prove the chain meets the standard.

Ensure the chain is tensioned with a turnbuckle or over-centre dog , not just pulled up by hand and hooked.

Verify edge protectors are in place wherever the chain contacts a sharp load edge.

Turnbuckles

Check the threads are clean and the body is not bent ; a bent turnbuckle can fail to hold tension.

Confirm the turnbuckle is locked (either a jam nut or safety wire) so vibration cannot back it off.

Make sure the turnbuckle has threads showing both ends — fully screwed in one end means it cannot take up any future slack.

Shackles and connectors

Check the pin is fully screwed in and secured (cotter pin or mouse if applicable).

Ensure the shackle body is not side-loaded — shackles are rated for in-line loads; side loading dramatically cuts their capacity.

Verify rated shackles only — never use lifting shackles of unknown provenance for transport restraint.

Twist locks

For containerised or flat-deck ISO loads, confirm every twist lock is positively engaged and in the locked position (the handle should be in the locked detent, not just resting).

Visually confirm each corner casting is seated on the twist lock with no gap.

Tarpaulins and load covering

Inspect the tarpaulin for tears, holes and worn patches — a flapping tarp can shred in the wind and either depart the vehicle or whip a following road user.

Check rope ties, eyelets and tie-down rings are intact and tight; loose rings let the tarp flap and wear through.

Confirm the tarp is not carrying load restraint duty unless it is a purpose-built restraint tarp — most tarps only cover the load, they do not restrain it.

In-trip checks

Restraint is not "set and forget." Two checkpoints matter:

Early re-check. Watch the load in your mirrors from the start, and at your first stop — the handbook's after-departure check comes after about an hour of driving — re-tension every lashing. New dunnage beds in, webbing stretches under load, and chains seat into the load, so slack often appears early in the trip.

Periodic walk-around. At every rest stop, fuel stop and work-diary break, walk around the load. Look for shifted items, loose or cut straps, bent chains, dropped turnbuckles, torn tarps and any sign of movement. Re-tension anything that has relaxed.

A load that has shifted is a warning, not a curiosity: if it moved once, the restraint in that direction is not meeting the 0.8g / 0.5g / 0.2g standard. Re-stack and re-restrain before continuing — a second shift may take it off the vehicle.