Study guide

6.1 Load Restraint Performance Standards

VicRoads Heavy Vehicle Knowledge Test — Rigid KT4

Track your progress as you read

Finished sections get a check mark.

1 Victorian Road Rules — Driver Obligations

Speed Limits for Heavy Vehicles in Victoria Zero BAC and Roadside Drug Testing for Heavy Vehicle Drivers Seatbelts, Parking Restrictions, and Night-Time Clearance Lighting Railway Crossing Procedures for Buses and Heavy Vehicles

2 Victorian Road Rules — Road Situations and Chain of Responsibility

Portable Warning Triangles: Carriage, Placement, and AS 3790 Following Distances, Lane Changes, and Turn Procedures for Long Vehicles Chain of Responsibility, Weighbridge Stops, and Enforcement Powers

3 Heavy Vehicle Law, Dimensions, and Access

Heavy Vehicle Licence Classes and Transmission Restrictions Mass and Dimension Limits for Rigid Vehicles Heavy Vehicle Road Signs, Access Restrictions, and Oversize/Overmass Permits

4 Vehicle Inspections and Roadworthiness

Pre-Operational Daily Checks: Cabin, Engine, Tyres, Brakes, and Lights Air Brake vs Hydraulic Brake System Checks and After-Departure Inspection Defect Identification, Roadworthiness Obligations, and Regular Mechanical Inspections

5 Vehicle Control, Braking, and Gear Selection

Double-Clutching and Gear Selection for Non-Synchromesh Gearboxes Braking Systems, Brake Fade, Stopping Distances, and Air Brake Delay Off-Tracking, Rollover Risk, Crash Avoidance Space, and Skid Correction

6 Load Restraint and Load Rules

6.1 Load Restraint Performance Standards 6.2 Tie-down vs Direct Restraint Methods 6.3 Load Placement, Distribution, Overhang Limits, and Load Security Checks

7 Fatigue Management and Work Diary

Standard Hours, BFM, AFM and ACH: Work/Rest Options and Fatigue-Regulated Vehicles National Driver Work Diary: Requirements, Completion, Record-Keeping, and Fatigue Prevention

8 Coupling and Combination Vehicle Rules

Coupling and Uncoupling: Procedures, Air Lines, Trailer Park Brake, Roll-Away Confirmation, and HC Licence Threshold

6.1 Load Restraint Performance Standards

Key Takeaways Explain This Topic AI

A load restraint system must withstand 0.8g forward and 0.5g sideways and rearward, plus 0.2g upward when relying on friction to resist the other forces (MDL Regulation, Schedule 7).

The g-values are fractions of the load's weight, so an 0.8g forward standard means restraint must hold 80% of the load's mass against a forward force (a 1 tonne load needs 800 kg equivalent of restraint).

The 0.2g upward standard applies whenever friction is relied on to withstand the forces in the other directions — a load blocked against the headboard but held sideways by tie-down still needs it.

These standards apply during normal driving, emergency braking, swerving, and rough roads — not just crash conditions — and the driver is responsible for ensuring restraint meets them.

A person who drives, or permits someone to drive, a heavy vehicle whose load does not comply with the loading requirements commits an offence (HVNL s. 111); loaders, packers and operators also have Chain of Responsibility duties.

Last updated: October 2026

Every load carried on a heavy rigid vehicle in Victoria must be restrained so it stays on the vehicle under all normal and emergency driving conditions. The performance benchmarks for that restraint are the loading performance standards in Schedule 7 of the Heavy Vehicle (Mass, Dimension and Loading) National Regulation, made under the Heavy Vehicle National Law (HVNL) that Victoria applies. The NHVR Load Restraint Guide explains how to meet them. Your restraint system — whether tie-down, direct, or a combination — must hold the load against each of them.

The four performance standards

The standards are expressed as multiples of gravitational acceleration, written as "g" where 1g equals the load's own weight. A force of 0.8g on a 1 tonne load is therefore equivalent to 800 kg of force pushing the load forward. The four required directions are:

  • Direction Required Force on a 1 tonne load When it applies
  • Forward 0.8g (80% of the load's weight) 800 kg equivalent Always
  • Sideways 0.5g (50%) 500 kg equivalent Always
  • Rearward 0.5g (50%) 500 kg equivalent Always
  • Upward 0.2g (20%) 200 kg equivalent When relying on friction to withstand the force in the other directions

The NHVR says these forces are what a heavy vehicle typically experiences when accelerating, cornering, and braking. The forward value is the highest because braking pushes the load forward hardest — the NHVR warns of loads that crash into the cabin during emergency braking. The upward value is the smallest, but it is often overlooked: road shock and vibration can momentarily unload a friction-based restraint, letting a load shift if it is not also held down.

What the g-values actually mean

A common exam trap is to read "0.8g" as "80% of the lashings' rated capacity." It is not. The g-value is the deceleration the load must survive , and the restraint system has to be designed so that its effective holding capacity in that direction is at least equal to the load's mass times the g-value. Worked example: a 2 tonne steel plate restrained only by tie-down friction must generate at least 2,000 × 0.8 = 1,600 kg of forward holding force from friction alone. Because friction equals normal force × coefficient of friction, and the friction between a smooth steel load and a steel deck is low, the lashing tension pressing the plate down has to be very high — which is exactly why direct restraint (chains blocked against a headboard) is preferred for dense, smooth items.

Why the upward standard matters

The 0.2g upward figure is tied to the way friction-based (tie-down) restraint works. Tie-down holds a load by clamping it to the deck so that friction resists sliding. If road bounce lifts the load even slightly, the clamping force drops, friction drops with it, and the load can walk forward. The upward standard forces you to put enough lashing tension — and enough lashings at a good angle — that even when the load tries to lift, the strap or chain still presses it down hard enough to keep friction alive. The standard applies whenever friction is relied on to withstand the force in the other directions. A load blocked forward against the headboard but held sideways by tie-down still relies on friction sideways, so the 0.2g upward requirement still applies. The NHVR notes some movement can be allowed — for example, a load contained within the sides of the vehicle and restrained from moving horizontally may be able to move vertically.

Where the standards come from and who enforces them

The standards sit in Schedule 7 of the Heavy Vehicle (Mass, Dimension and Loading) National Regulation , made under the loading requirements in Part 4.4 of the HVNL ; the NHVR Load Restraint Guide is the practical companion that shows how to meet them. Under HVNL s. 111, a person who drives, or permits another person to drive, a heavy vehicle on a road must ensure the vehicle and its load comply with the loading requirements. In Victoria they are enforced by Victoria Police and authorised officers. A load that fails any of the four performance standards is an unrestrained load for enforcement purposes, regardless of how many chains or straps you used — the question is always whether the system as a whole could hold the load at the g-value in that direction.

How to think about it on the truck

Three practical rules fall out of the standards:

Forward restraint is the hardest direction. Most loads that shift, shift forward under braking. Always size your forward restraint first — usually by blocking the load against a headboard, by direct chaining forward, or by very high-angle tie-down.

Friction is only useful while the load stays pressed down. That is why dunnage (timber or rubber packing) is used to raise the coefficient of friction, and why the upward standard exists.

Every direction has to be checked independently. A load well held forward but loose sideways will walk off on the first roundabout. Walk around the load and mentally test each direction against its g-value before you drive off.