Study guide
6.2 Tie-down vs Direct Restraint Methods
VicRoads Heavy Vehicle Knowledge Test — Rigid KT4
Track your progress as you read
Finished sections get a check mark.
1 Victorian Road Rules — Driver Obligations
Speed Limits for Heavy Vehicles in Victoria Zero BAC and Roadside Drug Testing for Heavy Vehicle Drivers Seatbelts, Parking Restrictions, and Night-Time Clearance Lighting Railway Crossing Procedures for Buses and Heavy Vehicles
2 Victorian Road Rules — Road Situations and Chain of Responsibility
Portable Warning Triangles: Carriage, Placement, and AS 3790 Following Distances, Lane Changes, and Turn Procedures for Long Vehicles Chain of Responsibility, Weighbridge Stops, and Enforcement Powers
3 Heavy Vehicle Law, Dimensions, and Access
Heavy Vehicle Licence Classes and Transmission Restrictions Mass and Dimension Limits for Rigid Vehicles Heavy Vehicle Road Signs, Access Restrictions, and Oversize/Overmass Permits
4 Vehicle Inspections and Roadworthiness
Pre-Operational Daily Checks: Cabin, Engine, Tyres, Brakes, and Lights Air Brake vs Hydraulic Brake System Checks and After-Departure Inspection Defect Identification, Roadworthiness Obligations, and Regular Mechanical Inspections
5 Vehicle Control, Braking, and Gear Selection
Double-Clutching and Gear Selection for Non-Synchromesh Gearboxes Braking Systems, Brake Fade, Stopping Distances, and Air Brake Delay Off-Tracking, Rollover Risk, Crash Avoidance Space, and Skid Correction
6 Load Restraint and Load Rules
6.1 Load Restraint Performance Standards 6.2 Tie-down vs Direct Restraint Methods 6.3 Load Placement, Distribution, Overhang Limits, and Load Security Checks
7 Fatigue Management and Work Diary
Standard Hours, BFM, AFM and ACH: Work/Rest Options and Fatigue-Regulated Vehicles National Driver Work Diary: Requirements, Completion, Record-Keeping, and Fatigue Prevention
8 Coupling and Combination Vehicle Rules
Coupling and Uncoupling: Procedures, Air Lines, Trailer Park Brake, Roll-Away Confirmation, and HC Licence Threshold
6.2 Tie-down vs Direct Restraint Methods
Key Takeaways Explain This Topic AI
Tie-down restraint uses lashing tension to clamp the load to the deck so friction resists movement; its holding power depends on lashing angle, pre-tension, dunnage and the coefficient of friction.
Lashing angle is critical: a strap at 90° to the deck delivers 100% of its tension as clamping force, at 60° it delivers 87%, 45° delivers 71%, 30° delivers 50%, and at 15° only 25% — low-angle straps are largely wasted.
Direct restraint physically blocks the load against a headboard, stanchion, or tied-off chain; the rule of thumb is 2× the load weight forward and 1× sideways and rearward, with chain angle kept under 25° from the deck.
Chains have a rated lashing capacity (LC) marked on them; a 10 mm transport chain typically has an LC around 3,000–4,000 kg and must be tensioned with a turnbuckle or dogs, not just hand-pulled.
Mixed systems are common — a load blocked forward by a headboard (direct) and held down and sideways by tie-down straps — but every direction must still meet its g-value performance standard.
Last updated: July 2026
Every load restraint system on a heavy rigid vehicle is built from one or both of two methods: tie-down (friction-based) and direct (blocking). Knowing which method you are using — and sizing it correctly — is the core skill tested in this chapter and the core thing an inspector checks at the roadside.
Tie-down: clamping the load so friction does the work
Tie-down does not stop the load directly. It works by pulling the load down onto the deck so that the friction between load and deck resists sliding. The holding force in any direction equals the clamping force × the coefficient of friction (CoF). Clamping force comes from lashing tension, but only the component of that tension that acts perpendicular to the deck contributes — and that component depends on the lashing angle.
The lashing-angle penalty
The angle is measured between the lashing and the deck plane. The closer to vertical (90°), the more of the strap's tension presses the load down. As the angle flattens, more tension pulls along the deck (useless for clamping) and less presses down:
- Lashing angle to deck % of tension that clamps the load Effective clamping from a 1,000 kg strap
- 90° (ideal) 100% 1,000 kg
- 60° 87% 870 kg
- 45° 71% 710 kg
- 30° 50% 500 kg
- 15° (poor) 25% 250 kg
A strap pulled flat across a low load at 15° loses three-quarters of its clamping ability. This is why the Load Restraint Guide pushes you to either raise the load (taller dunnage, taller headboard) so the strap can run at a steeper angle, or to use more straps, or to switch to direct restraint. Practical rule of thumb: keep tie-down lashings at 45° or steeper wherever possible; below 30° you are largely wasting the strap.
What makes tie-down work
Three levers improve tie-down performance:
Pre-tension — the initial tension you put into the lashing with a turnbuckle, ratchet or dogs. Higher pre-tension means more clamping force and more friction. The lashing's rated pre-tension (e.g. 300–500 kg for a typical ratchet strap) caps how much you can achieve per strap.
Coefficient of friction — steel on bare steel is about 0.3; timber dunnage on a steel deck is about 0.45; rubber matting can take it to 0.6 or higher. Always use dunnage or rubber to raise the CoF for smooth hard loads.
Number and placement of lashings — lashings must be spaced so that the whole load is clamped, not just the part under each strap. Friction is local; an unstrapped section of a long load is effectively unrestrained.
Direct restraint: blocking the load physically
Direct restraint physically prevents the load from moving in a given direction. It works by attaching the load — with chains, straps or structure — to a fixed point on the vehicle: a headboard, a coaming rail, a stanchion, or a tied-off chain to an anchor point. Because the restraint member takes the load directly in tension or shear, friction is irrelevant and angle penalties mostly disappear (within limits).
Direct-restraint capacity rules of thumb
The NHVR guide gives simple capacity rules of thumb for direct restraint so a driver can size chains without doing full engineering maths:
Direction Direct restraint capacity required Why
Forward 2× the load's weight Covers the 0.8g deceleration plus a safety margin for shock loading and chain angle inefficiency.
Sideways 1× the load's weight Covers the 0.5g lateral standard with margin.
Rearward 1× the load's weight Covers the 0.5g rearward standard with margin.
So a 2 tonne item directly chained forward needs a chain arrangement rated for at least 4,000 kg forward holding capacity. If two chains share the forward load equally, each must be rated for at least 2,000 kg.
Chain angle from the deck
For direct restraint, the chain angle is measured between the chain and the deck when looking along the direction of restraint. Keep this angle under 25° — i.e. the chain should run fairly close to the deck, not up at a steep angle. A steeply angled chain wastes capacity pulling the load down instead of stopping it, and can actually add a lift component. Low, straight chain runs to anchor points near the load base are most efficient.
Chains, turnbuckles, shackles and rated gear
Direct restraint almost always uses chain because of its high lashing capacity (LC) and resistance to cutting and abrasion. Key requirements:
The chain must be marked with its lashing capacity (LC) — a 10 mm Grade 80 transport chain is typically rated around 3,000–4,000 kg LC; 13 mm around 5,000–6,000 kg. Never use lifting chain grade markings as a substitute for transport chain LC.
Tension with a turnbuckle or over-centre dogs , never by hand-pulling and hooking — the pre-tension is what takes up slack when the load shifts under braking.
Connect with rated shackles , not hooking chain links directly over sharp edges; sharp edges need edge protectors.
Twist locks and container locks are a form of direct restraint for ISO containers and flat-deck ISO-fitted loads; the corner castings engage the twist locks and the container is blocked in all four directions.
Tie-down vs direct — at a glance
- Feature Tie-down Direct
- How it holds the load Friction from clamping force Physically blocks movement
- Sensitive to lashing angle Yes — clamping drops sharply below 45° Less — chain angle kept under 25° from deck
- Sensitive to friction (CoF) Yes — needs dunnage/rubber No — friction irrelevant
- Typical equipment Ratchet straps, webbing Chains, turnbuckles, shackles, headboard, stanchions, twist locks
Best for Loads with good friction surface, irregular shapes that conform to deck Heavy, dense, smooth items (steel, machinery), containerised loads
Capacity rule of thumb Sum of (pre-tension × angle factor × CoF) per strap 2× load weight forward, 1× sideways and rearward
Mixed systems
Most real loads use a combination: a headboard or stanchion blocks the load forward (direct), straps clamp it down and sideways (tie-down), and a rear chain or strap blocks rearward (direct). The rule is that each of the four directions must independently meet its g-value performance standard — you cannot trade off a weak direction against a strong one. Walk around the finished load, point at each direction, and ask: "What is holding this against 0.8g / 0.5g / 0.5g / 0.2g here?"