Study guide
Following Distances, Lane Changes, and Turn Procedures for Long Vehicles
VicRoads Heavy Vehicle Knowledge Test — Rigid KT4
Track your progress as you read
Finished sections get a check mark.
1 Victorian Road Rules — Driver Obligations
Speed Limits for Heavy Vehicles in Victoria Zero BAC and Roadside Drug Testing for Heavy Vehicle Drivers Seatbelts, Parking Restrictions, and Night-Time Clearance Lighting Railway Crossing Procedures for Buses and Heavy Vehicles
2 Victorian Road Rules — Road Situations and Chain of Responsibility
Portable Warning Triangles: Carriage, Placement, and AS 3790 Following Distances, Lane Changes, and Turn Procedures for Long Vehicles Chain of Responsibility, Weighbridge Stops, and Enforcement Powers
3 Heavy Vehicle Law, Dimensions, and Access
Heavy Vehicle Licence Classes and Transmission Restrictions Mass and Dimension Limits for Rigid Vehicles Heavy Vehicle Road Signs, Access Restrictions, and Oversize/Overmass Permits
4 Vehicle Inspections and Roadworthiness
Pre-Operational Daily Checks: Cabin, Engine, Tyres, Brakes, and Lights Air Brake vs Hydraulic Brake System Checks and After-Departure Inspection Defect Identification, Roadworthiness Obligations, and Regular Mechanical Inspections
5 Vehicle Control, Braking, and Gear Selection
Double-Clutching and Gear Selection for Non-Synchromesh Gearboxes Braking Systems, Brake Fade, Stopping Distances, and Air Brake Delay Off-Tracking, Rollover Risk, Crash Avoidance Space, and Skid Correction
6 Load Restraint and Load Rules
6.1 Load Restraint Performance Standards 6.2 Tie-down vs Direct Restraint Methods 6.3 Load Placement, Distribution, Overhang Limits, and Load Security Checks
7 Fatigue Management and Work Diary
Standard Hours, BFM, AFM and ACH: Work/Rest Options and Fatigue-Regulated Vehicles National Driver Work Diary: Requirements, Completion, Record-Keeping, and Fatigue Prevention
8 Coupling and Combination Vehicle Rules
Coupling and Uncoupling: Procedures, Air Lines, Trailer Park Brake, Roll-Away Confirmation, and HC Licence Threshold
Following Distances, Lane Changes, and Turn Procedures for Long Vehicles
Key Takeaways Explain This Topic AI
A long vehicle (7.5 m or longer) must keep at least 60 m behind another long vehicle, except on a multi-lane road, in a built-up area, or when overtaking.
A road train must keep at least 200 m behind a long vehicle under the same rule; 60 m and 200 m are legal minimums, not safe stopping gaps.
The Do Not Overtake Turning Vehicle sign is optional; a long vehicle displaying it may use more than one lane to turn within 50 m of the corner, and others must not overtake on the turning side.
Cut-in is the rear wheels following a shorter path than the front wheels in a turn; start a left turn further into the intersection and do not swing wider than needed.
Signal long enough to warn others; the fixed 5-second minimum applies when moving off from the side of the road.
Last updated: October 2026
Following Distances, Lane Changes, and Turn Procedures for Long Vehicles
Quick Answer: A long vehicle (7.5 m or longer, including any load or projection) must keep at least 60 metres behind another long vehicle, and a road train at least 200 metres — except on a multi-lane road , in a built-up area , or when overtaking (Road Safety Road Rules r. 127). Sixty metres is a legal minimum, not a safe stopping gap. A long vehicle that displays a Do Not Overtake Turning Vehicle sign may use more than one lane to turn when within 50 m of the corner; without the sign it must stay as near as possible within its lane. Cut-in is the rear wheels following a shorter path than the front wheels in a turn.
What Counts as a Long Vehicle?
Under rule 127 of Victoria's Road Safety Road Rules, a long vehicle is a vehicle that, together with any load or projection, is 7.5 metres long or longer . The handbook puts it the same way: "any vehicle which, together with its trailer, is at least 7.5 metres long". Most HR rigid trucks are long vehicles. A road train is a much longer multi-trailer combination; the 200 m rule is aimed at those, but the exam can ask about both numbers.
The 60 m and 200 m Following Rule
Rule 127 requires a long vehicle to stay at least the required minimum distance behind another long vehicle in front, unless the driver is:
driving on a multi-lane road (a road with two or more marked lanes for traffic in your direction, such as most freeways);
driving on any length of road in a built-up area ; or
overtaking .
- Vehicle you are driving Vehicle ahead Minimum distance (where r. 127 applies)
- Long vehicle (7.5 m or longer), not a road train Long vehicle 60 metres
- Road train Long vehicle 200 metres
- Any vehicle Any vehicle A distance that lets you stop safely (general rule)
Why is 60 m only a minimum?
The 60 m rule keeps long vehicles spaced so other drivers can overtake one truck at a time. It is not a stopping gap. The handbook's stopping table shows a typical heavy vehicle needs about 215 m to stop from 100 km/h on a dry road, and its recommended gap is 6.0–7.0 seconds behind the vehicle in front at 100 km/h (4.5 seconds at 60 km/h), doubled when the road is wet, traffic is heavy or vision is restricted. Keep the larger safe gap; the 60 m figure only sets the legal floor between long vehicles.
Worked Example
You are driving an 8 m HR rigid on a country highway with one lane each way, outside a built-up area, and you come up behind another rigid truck. Rule 127 applies, so you must keep at least 60 m back. In practice keep much more: at 100 km/h the handbook's guide is 6–7 seconds. Pick a fixed object such as a sign or bridge, count the seconds after the truck ahead passes it, and ease off if you reach it too soon.
On a divided freeway with two lanes each way, rule 127 does not apply because it is a multi-lane road — but you still need a safe stopping gap.
Lane Changes for Long Vehicles
Long vehicles cannot change lanes as crisply as cars. Key points:
Signal long enough — rule 46 requires the change-of-direction signal to be given for long enough to give sufficient warning to other drivers and pedestrians. The fixed 5-second minimum applies when you move off from a stationary position at the side of the road (or from a median strip parking area).
Check mirrors and blind spots — a rigid truck has large blind spots on both sides, especially the left side. Use the main and wide-angle mirrors before and during the change.
Move gradually — a sudden lane change in a laden rigid can shift the load and cause a rollover, particularly at higher speeds or in the wet.
Stay within your lane — without a displayed Do Not Overtake Turning Vehicle sign, a long vehicle must drive as near as possible within the marked lane, including when turning.
Turn Procedures and Cut-In
What is cut-in?
The handbook defines it simply: "When any vehicle goes around a curve or turn, the rear wheels usually follow a shorter path than the front ones. This is called cut-in." The longer the vehicle and the sharper the turn, the greater the cut-in. It is also called off-tracking . In a left turn the rear wheels cut towards the kerb; in a right turn they cut towards vehicles waiting in the street you enter.
To allow for it, heavy vehicle drivers start a left turn further into the intersection than a car, so the back wheels do not run over the kerb, and use the left mirror to check they will clear poles and parked cars. For a right turn, get close to the middle of the intersection before turning. The handbook adds: "Do not swing wider than you have to from the kerb", and position the vehicle so others cannot overtake on your left.
Do Not Overtake Turning Vehicle Sign
The sign may be attached to the rear of a heavy vehicle 7.5 m or longer — it is optional. When a long vehicle displays the sign:
The driver may use more than one lane to turn, if it is needed and safe, and must be within 50 metres of the corner when moving out of the lane.
Other drivers must not pass or overtake the turning vehicle on the side it is turning towards while it is turning (Road Safety Road Rules r. 143).
If the vehicle is under 7.5 m, or does not display the sign, the driver must stay as near as possible within the marked lane, even when turning.
Worked Example: Left Turn at a Signalised Intersection
You are driving an HR rigid with a 9 m tray, displaying a Do Not Overtake Turning Vehicle sign, approaching a left turn from a two-lane road. The rear of your truck will cut in. You:
Indicate left in good time.
Drive further into the intersection than a car before starting to turn; within 50 m of the corner you may use part of the next lane if you need it and it is safe.
Check the left mirror before and during the turn for cyclists, poles and parked cars.
Do not swing wider than you have to, and place the truck so traffic cannot overtake on your left.
A driver who passes you on the left while you are turning with the sign displayed commits an offence. But as the truck driver you still have to check and turn only when it is safe.
Common Exam Traps
Trap 1: "60 m applies on every highway." No — r. 127 does not apply on a multi-lane road, in a built-up area, or while overtaking.
Trap 2: "The 200 m rule applies to any long vehicle behind a road train." No — 200 m applies when you are driving a road train behind a long vehicle. A long vehicle that is not a road train uses the 60 m rule.
Trap 3: "The Do Not Overtake Turning Vehicle sign lets the truck turn from any lane regardless of arrows." No — the truck must still obey lane arrows and traffic signals; the sign only permits using more than one lane to complete a turn, within 50 m of the corner.
Trap 4: "Cut-in only happens on semi-trailers." No — any vehicle's rear wheels follow a shorter path in a turn; the longer the vehicle, the more it cuts in.
Trap 5: "Every long vehicle must display the sign." No — the sign is optional; without it the vehicle must keep within its lane.
Victorian Enforcement
Following too close and overtaking a turning long vehicle are enforced by Victoria Police. For you as the HR driver, the duty is to keep the legal and safe gaps, signal correctly, and turn only when safe.