Study guide

Braking Systems, Brake Fade, Stopping Distances, and Air Brake Delay

VicRoads Heavy Vehicle Knowledge Test — Rigid KT4

Track your progress as you read

Finished sections get a check mark.

1 Victorian Road Rules — Driver Obligations

Speed Limits for Heavy Vehicles in Victoria Zero BAC and Roadside Drug Testing for Heavy Vehicle Drivers Seatbelts, Parking Restrictions, and Night-Time Clearance Lighting Railway Crossing Procedures for Buses and Heavy Vehicles

2 Victorian Road Rules — Road Situations and Chain of Responsibility

Portable Warning Triangles: Carriage, Placement, and AS 3790 Following Distances, Lane Changes, and Turn Procedures for Long Vehicles Chain of Responsibility, Weighbridge Stops, and Enforcement Powers

3 Heavy Vehicle Law, Dimensions, and Access

Heavy Vehicle Licence Classes and Transmission Restrictions Mass and Dimension Limits for Rigid Vehicles Heavy Vehicle Road Signs, Access Restrictions, and Oversize/Overmass Permits

4 Vehicle Inspections and Roadworthiness

Pre-Operational Daily Checks: Cabin, Engine, Tyres, Brakes, and Lights Air Brake vs Hydraulic Brake System Checks and After-Departure Inspection Defect Identification, Roadworthiness Obligations, and Regular Mechanical Inspections

5 Vehicle Control, Braking, and Gear Selection

Double-Clutching and Gear Selection for Non-Synchromesh Gearboxes Braking Systems, Brake Fade, Stopping Distances, and Air Brake Delay Off-Tracking, Rollover Risk, Crash Avoidance Space, and Skid Correction

6 Load Restraint and Load Rules

6.1 Load Restraint Performance Standards 6.2 Tie-down vs Direct Restraint Methods 6.3 Load Placement, Distribution, Overhang Limits, and Load Security Checks

7 Fatigue Management and Work Diary

Standard Hours, BFM, AFM and ACH: Work/Rest Options and Fatigue-Regulated Vehicles National Driver Work Diary: Requirements, Completion, Record-Keeping, and Fatigue Prevention

8 Coupling and Combination Vehicle Rules

Coupling and Uncoupling: Procedures, Air Lines, Trailer Park Brake, Roll-Away Confirmation, and HC Licence Threshold

Braking Systems, Brake Fade, Stopping Distances, and Air Brake Delay

Key Takeaways Explain This Topic AI

Air brakes use compressed air to apply the brakes; the handbook says there is a delay of up to one second for air to reach the brakes after you press the pedal — 17 metres travelled at 60 km/h.

Spring brakes are held off by air pressure; when there is a serious air loss the springs apply the brakes automatically — a fail-safe, so be ready for the wheels to lock if the load is light.

Brake fade occurs when prolonged braking on descents overheats the brake friction material, reducing braking effectiveness — use auxiliary retarders (exhaust or engine brakes) to reduce service brake demand

An empty vehicle can lock its wheels more easily than a loaded one because there is less weight on the tyres providing traction — the same brake force applied to less mass produces faster deceleration

Braking distance increases with the square of speed: a heavy vehicle at 80 km/h needs roughly four times the braking distance of one at 40 km/h, before adding reaction time and air brake delay

Last updated: October 2026

Braking System Types on Heavy Rigid Vehicles

Heavy rigid vehicles may use several braking technologies, often in combination. Understanding how each works — and how each can fail — is essential for safe operation and for the Victorian HR knowledge test.

Comparison of Heavy Vehicle Braking Systems

System How It Works Failure Mode

Air brakes (service) Compressed air stored in tanks is routed through valves to brake chambers when the driver presses the pedal; air pressure pushes a diaphragm that moves the pushrod, applying brake shoes to drums or pads to discs Air leakage or compressor failure lowers pressure; the low-pressure warning comes on, and a serious air loss lets the spring brakes apply

Hydraulic brakes Brake fluid under pressure from the master cylinder actuates wheel cylinders or calipers; common on lighter rigid vehicles (under ~8t GVM) and some medium trucks Fluid leak, boiled fluid (vapour lock from overheating), or master cylinder failure leads to soft or no pedal

Spring brakes (parking/emergency) Springs push the brakes on and are held back by air pressure; when there is a serious air loss the brakes go on automatically; used for parking and as an emergency fail-safe If air pressure is lost while driving, spring brakes apply and can lock the wheels — driver must pull over safely and stop

Auxiliary retarders Engine brake (compressor release / 'Jake brake'), exhaust brake (restricts exhaust flow), or transmission retarder (electromagnetic or hydraulic) — all provide deceleration force without using service brakes Overheating of the retarder itself on very long descents, or reduced effectiveness at low engine RPM; not a substitute for service brakes at very low speeds

Trailer brakes On vehicles towing a trailer, air is supplied through the 'emergency' (supply/red) and 'service' (control/blue or yellow) lines; the trailer's brake chambers apply in proportion to the towing vehicle's service brake Disconnection or rupture of air lines causes trailer spring brakes to apply; incorrect coupling leaves trailer with no braking

Brake Fade on Descents

Brake fade is the loss of braking effectiveness that occurs when brake friction material overheats. The handbook puts it simply: continuous heavy braking on a long hill makes the linings heat up until the brakes no longer slow the vehicle. On long downhill sections, continuous light braking can cause drums to heat up until the brakes produce almost no retardation.

Symptoms of brake fade include:

  • The brake pedal feels normal but the vehicle does not slow as expected
  • Increasing pedal travel with diminishing response
  • A burning smell from the brake area
  • In severe cases, brake smoke
  • Preventing brake fade

The key strategy is to reduce reliance on the service brakes on descents:

Select a low gear before the descent so the engine provides braking through compression (engine braking).

Use an auxiliary retarder (exhaust brake or engine brake) to provide continuous deceleration without heating the service brakes.

Use the service brakes in firm applications rather than dragging them continuously. The handbook says to use the brakes to prevent speed build-up before it occurs: apply the brakes firmly to reduce your speed, then release them to prevent brake fade, and repeat when you need to (often called snub braking ). This manages brake temperature far better than constant light pressure.

Never exceed the speed at which the selected gear can hold the vehicle. If speed builds up beyond what the gear can manage, you will need heavy braking — which causes fade.

Empty vs Loaded Braking

A common misconception is that an empty vehicle is easier to stop safely. In reality, braking dynamics change significantly with load:

Loaded vehicle: More mass means more kinetic energy to dissipate, so the vehicle needs a longer stopping distance at the same speed. However, the extra weight also increases the downward force on the tyres, providing more traction (grip) and allowing harder brake application before the wheels lock.

Empty vehicle: Less mass means less kinetic energy, so theoretically shorter stopping distance. But the reduced weight on the driving and braking axles means less traction. The same brake force that merely slows a loaded truck can lock the wheels of an empty one. Once wheels lock, the vehicle loses directional control and the braking distance actually increases (a sliding tyre has less grip than a rolling tyre under threshold braking).

This is particularly dangerous when a driver is accustomed to a loaded vehicle and then drives empty: the brakes feel much more sensitive, and a panic application can lock the wheels. Drivers must adjust pedal pressure based on load — lighter pressure when empty.

Air Brake Delay

Air brake systems have an inherent lag between the moment the driver presses the brake pedal and the moment the brake chambers at the rear of the vehicle (or on the trailer) actually apply. This delay exists because:

Air must travel through the supply and control lines from the foot valve to the relay valve and then to the brake chambers.

The longer the air lines (long vehicle or vehicle plus trailer), the greater the volume that must be pressurised before the brakes move.

Air is compressible, unlike hydraulic fluid which is effectively instantaneous.

The handbook says there is a delay of up to one second for air to reach the brakes after you push the pedal — at 60 km/h you travel 17 metres from when you begin to push the pedal until the brakes start to work. At 80 km/h (22.2 m/s), a one-second delay means about 22 metres . This must be factored into following distances and approach speeds.

Compensating for air brake delay

Maintain a Crash Avoidance Space (discussed in the next section) that accounts for the delay — do not follow other vehicles at the same distance a car would.

Begin brake applications earlier than you would in a light vehicle, particularly when approaching intersections or stopped traffic.

On vehicles with trailers, ensure the trailer brake valve (load-sensing valve or relay emergency valve) is correctly adjusted so the trailer brakes apply slightly before the towing vehicle's brakes — this prevents the trailer pushing the towing vehicle (jackknife risk).

Stopping Distances

The total stopping distance for a heavy vehicle is the sum of:

Reaction distance: The handbook says it can take two to three seconds to see a problem ahead and get your foot to the brake pedal.

Air brake lag distance: Up to one more second before the brakes start to work. The handbook's summary: it could be as long as 3 seconds after you've seen a problem before the vehicle begins to slow — about 51 metres at just 60 km/h.

Braking distance: Distance travelled from when brakes apply to when the vehicle stops.

The handbook's stopping table for a typical heavy vehicle (dry road, roadworthy tyres, fit and alert driver) gives a total stopping distance of about 215 metres from 100 km/h .

Stopping distance increases with the square of speed . If speed doubles, braking distance increases fourfold. A heavy rigid vehicle at 100 km/h needs roughly four times the braking distance of the same vehicle at 50 km/h — before adding the extra reaction and air brake lag distance from the higher speed.

Because a heavy vehicle's service brakes, load and retarder all interact, the safest approach is to always maintain speed margins that leave plenty of room. The Victorian 100 km/h maximum for heavy vehicles is not just a legal limit — it is a safety limit reflecting the long stopping distances at highway speeds.