Study guide
Off-Tracking, Rollover Risk, Crash Avoidance Space, and Skid Correction
VicRoads Heavy Vehicle Knowledge Test — Rigid KT4
Track your progress as you read
Finished sections get a check mark.
1 Victorian Road Rules — Driver Obligations
Speed Limits for Heavy Vehicles in Victoria Zero BAC and Roadside Drug Testing for Heavy Vehicle Drivers Seatbelts, Parking Restrictions, and Night-Time Clearance Lighting Railway Crossing Procedures for Buses and Heavy Vehicles
2 Victorian Road Rules — Road Situations and Chain of Responsibility
Portable Warning Triangles: Carriage, Placement, and AS 3790 Following Distances, Lane Changes, and Turn Procedures for Long Vehicles Chain of Responsibility, Weighbridge Stops, and Enforcement Powers
3 Heavy Vehicle Law, Dimensions, and Access
Heavy Vehicle Licence Classes and Transmission Restrictions Mass and Dimension Limits for Rigid Vehicles Heavy Vehicle Road Signs, Access Restrictions, and Oversize/Overmass Permits
4 Vehicle Inspections and Roadworthiness
Pre-Operational Daily Checks: Cabin, Engine, Tyres, Brakes, and Lights Air Brake vs Hydraulic Brake System Checks and After-Departure Inspection Defect Identification, Roadworthiness Obligations, and Regular Mechanical Inspections
5 Vehicle Control, Braking, and Gear Selection
Double-Clutching and Gear Selection for Non-Synchromesh Gearboxes Braking Systems, Brake Fade, Stopping Distances, and Air Brake Delay Off-Tracking, Rollover Risk, Crash Avoidance Space, and Skid Correction
6 Load Restraint and Load Rules
6.1 Load Restraint Performance Standards 6.2 Tie-down vs Direct Restraint Methods 6.3 Load Placement, Distribution, Overhang Limits, and Load Security Checks
7 Fatigue Management and Work Diary
Standard Hours, BFM, AFM and ACH: Work/Rest Options and Fatigue-Regulated Vehicles National Driver Work Diary: Requirements, Completion, Record-Keeping, and Fatigue Prevention
8 Coupling and Combination Vehicle Rules
Coupling and Uncoupling: Procedures, Air Lines, Trailer Park Brake, Roll-Away Confirmation, and HC Licence Threshold
Off-Tracking, Rollover Risk, Crash Avoidance Space, and Skid Correction
Key Takeaways Explain This Topic AI
Off-tracking (cut-in) means the rear wheels follow a shorter path than the front wheels through a turn — start a left turn further into the intersection than a car, and do not swing wider than you have to.
Rollover risk is highest on a loaded heavy rigid vehicle because of its high centre of gravity; it can roll at cornering forces a car handles easily — reduce speed before cornering, not during it.
Crash Avoidance Space means looking and planning about 12–15 seconds ahead (handbook) and keeping space all around; scan your mirrors constantly because heavy vehicles have large blind spots.
Skid correction depends on the skid type: ease off the brake or accelerator and steer smoothly in the direction you want to go — never brake hard in a skid
Emergency braking and evasive steering are last-resort techniques: threshold brake (maximum pressure without locking) if stopping is the answer, or steer around the hazard while looking where you want to go if a lane change is possible
Last updated: October 2026
Off-Tracking on Corners
Off-tracking (or cut-in) is the phenomenon where the rear wheels of a long vehicle do not follow exactly in the path of the front wheels when cornering. The rear of the vehicle tracks a tighter radius than the front — it cuts toward the inside of the turn.
The longer the vehicle and the tighter the turn, the greater the off-tracking. On a heavy rigid vehicle this effect is significant because the wheelbase is long. If the driver positions the vehicle as a car would (hugging the inside of the lane), the rear wheels will cut inside and may mount a kerb, clip a cyclist, or cross into an adjacent lane.
Managing off-tracking
The handbook's method:
Left turns: start the turn further into the intersection than a car would, so the back wheels do not run over the kerb — the longer the vehicle, the further in you go. Use the left mirror to check you will clear poles and parked cars. You may need to approach the turn wide, but do not swing wider than you have to from the kerb, and place the vehicle so traffic behind cannot overtake on your left.
Right turns: get close to the middle of the intersection before you start to turn, so the rear does not cut in towards vehicles waiting in the street you are entering.
A vehicle 7.5 m or longer that displays a Do Not Overtake Turning Vehicle sign may use more than one lane to turn, when within 50 m of the corner and when it is safe; other drivers must not overtake it on the turning side. Without the sign, stay as near as possible within your lane.
Rollover Risk and High Centre of Gravity
Heavy rigid vehicles have a high centre of gravity compared to cars, especially when loaded. The higher the centre of gravity and the greater the load, the easier the vehicle is to roll over in a corner or during sudden steering inputs.
A loaded heavy vehicle can roll over at speeds and cornering forces that feel unremarkable to a car driver.
Rollover prevention
Reduce speed before cornering, not during it. All braking and gear selection should be complete before the turn. Braking mid-corner shifts weight forward and reduces traction on the rear (drive) axle, increasing the risk of a spin or rollover.
Steer smoothly. Avoid sudden steering inputs. A quick steering correction that would be routine in a car can initiate a rollover in a loaded heavy vehicle because it generates a rapid lateral acceleration.
Secure the load. An unsecured or shifting load changes the centre of gravity dynamically. A load that shifts to one side during cornering can trigger a rollover at a speed that would otherwise be safe.
Be cautious on roundabouts and off-ramps. These are common rollover sites because drivers enter them at car-like speeds.
Crash Avoidance Space (CAS)
Crash Avoidance Space (CAS) is the core concept of Low Risk Driving (LRD). It means maintaining a buffer of time and space around the vehicle so that if a hazard appears, the driver has room to react and stop or steer.
The 12–15 second rule
The handbook says to look and plan about 12–15 seconds ahead , because heavy vehicles take longer to stop — about a city block in built-up areas, and on the open road about a kilometre ahead when you can. At 100 km/h, 12 seconds equates to roughly 330 metres. This gives the driver time to identify hazards — stopped traffic, debris, roadworks, merging vehicles — and begin reducing speed or planning a lane change well before reaching them.
A heavy vehicle needs this lead time because of its longer stopping distance and air brake delay.
Following distance
The handbook's table gives the time to leave behind the vehicle in front, on a dry, good-quality sealed road with good tyres and brakes:
- Speed Seconds behind the vehicle in front
- 25 km/h 3.0
- 40 km/h 3.5
- 60 km/h 4.5
- 75 km/h 5.0
- 90 km/h 5.5
- 100 km/h 6.0–7.0
Double the gap if the road is wet, traffic is heavy or vision is restricted, and on gravel roads; increase it at night. Count the seconds from when the vehicle ahead passes a roadside object until you reach it. The 60-metre rule for long vehicles is only a legal minimum — at 100 km/h, 6 seconds is about 167 metres.
Mirror checks
A heavy vehicle has significant blind spots — particularly down the left (passenger) side, where a car or motorcycle can disappear entirely; the handbook notes vehicles on your left are always harder to see in your mirrors. Use your mirrors and scan constantly — both sides, near and far — and always before any lane change, turn, or braking manoeuvre.
Skid Types and Correction
Skids occur when tyres exceed their available grip — either from too much braking, too much acceleration, or too much steering for the conditions. Heavy vehicles are particularly prone because of their high mass, long wheelbase, and (for empty vehicles) low rear-axle traction.
Skid Type and Correction Table
Skid Type Cause How to Correct
Drive-wheel (power) skid Too much throttle for available grip; rear drive wheels spin and the rear of the vehicle steps out Ease off the accelerator immediately; do not brake; steer smoothly in the direction you want the vehicle to go; the rear will regain traction as speed drops
Braking skid (wheel lock-up) Brakes applied too hard, wheels lock and the vehicle slides straight regardless of steering input Release the brake pedal to unlock the wheels; reapply at a lighter pressure (threshold braking); steer in the direction you want to go — a rolling tyre can grip, a locked tyre cannot
Trailer swing / jackknife Trailer brakes lock or the trailer pushes the towing vehicle during braking or on a slippery surface; the trailer rotates out of line with the prime mover Ease off the brake; if the trailer is swinging out, a slight acceleration can pull the combination straight; do not brake hard — that worsens the jackknife; steer to align the vehicle
Front-wheel skid (understeer) Too much speed or steering for the available grip; front wheels slide wide and the vehicle will not turn in Ease off the accelerator (or brake gently if on a straight); do not add more steering — this reduces grip further; wait for the front wheels to regain traction, then steer smoothly
The universal principle: ease off whatever caused the skid (brake or throttle), look where you want to go, and steer smoothly in that direction. Never brake hard in a skid — locking more wheels reduces control further.
Emergency Braking and Evasive Steering
When a hazard appears suddenly and there is no time for a normal stop, the driver must choose between two last-resort techniques:
Emergency (threshold) braking
If the path ahead is clear and the answer is to stop:
Apply firm, steady brake pressure — the maximum you can sustain without locking the wheels (threshold braking). If the vehicle has ABS, press the pedal hard and hold it; ABS will prevent lock-up.
Keep both hands on the wheel and steer straight. Do not pump the pedal on an ABS-equipped vehicle.
If wheels lock (non-ABS), release slightly and reapply — a rolling wheel can steer, a locked one cannot.
Use the auxiliary retarder (exhaust or engine brake) simultaneously to add deceleration without heating the service brakes.
Evasive steering
If stopping in time is not possible but a clear path exists to the side:
Look at where you want to go — not at the obstacle. The hands follow the eyes.
Steer smoothly and firmly around the hazard. A heavy vehicle can often steer around an obstacle in less distance than it can stop, particularly at higher speeds.
Counter-steer to bring the vehicle back onto your original path once past the hazard — do not over-correct.
If leaving the road is the only option, steer onto the shoulder or a clear area and brake gradually once off the sealed surface. Do not swerve into oncoming traffic.
The decision between braking and steering must be made in under a second. This is why looking 12–15 seconds ahead and keeping Crash Avoidance Space is critical — it gives the driver time to choose the best option rather than reacting instinctively, which often results in a locked-wheel skid straight into the hazard.