Study guide
Air Brake vs Hydraulic Brake System Checks and After-Departure Inspection
VicRoads Heavy Vehicle Knowledge Test — Rigid KT4
Track your progress as you read
Finished sections get a check mark.
1 Victorian Road Rules — Driver Obligations
Speed Limits for Heavy Vehicles in Victoria Zero BAC and Roadside Drug Testing for Heavy Vehicle Drivers Seatbelts, Parking Restrictions, and Night-Time Clearance Lighting Railway Crossing Procedures for Buses and Heavy Vehicles
2 Victorian Road Rules — Road Situations and Chain of Responsibility
Portable Warning Triangles: Carriage, Placement, and AS 3790 Following Distances, Lane Changes, and Turn Procedures for Long Vehicles Chain of Responsibility, Weighbridge Stops, and Enforcement Powers
3 Heavy Vehicle Law, Dimensions, and Access
Heavy Vehicle Licence Classes and Transmission Restrictions Mass and Dimension Limits for Rigid Vehicles Heavy Vehicle Road Signs, Access Restrictions, and Oversize/Overmass Permits
4 Vehicle Inspections and Roadworthiness
Pre-Operational Daily Checks: Cabin, Engine, Tyres, Brakes, and Lights Air Brake vs Hydraulic Brake System Checks and After-Departure Inspection Defect Identification, Roadworthiness Obligations, and Regular Mechanical Inspections
5 Vehicle Control, Braking, and Gear Selection
Double-Clutching and Gear Selection for Non-Synchromesh Gearboxes Braking Systems, Brake Fade, Stopping Distances, and Air Brake Delay Off-Tracking, Rollover Risk, Crash Avoidance Space, and Skid Correction
6 Load Restraint and Load Rules
6.1 Load Restraint Performance Standards 6.2 Tie-down vs Direct Restraint Methods 6.3 Load Placement, Distribution, Overhang Limits, and Load Security Checks
7 Fatigue Management and Work Diary
Standard Hours, BFM, AFM and ACH: Work/Rest Options and Fatigue-Regulated Vehicles National Driver Work Diary: Requirements, Completion, Record-Keeping, and Fatigue Prevention
8 Coupling and Combination Vehicle Rules
Coupling and Uncoupling: Procedures, Air Lines, Trailer Park Brake, Roll-Away Confirmation, and HC Licence Threshold
Air Brake vs Hydraulic Brake System Checks and After-Departure Inspection
Key Takeaways Explain This Topic AI
An air-brake system must build pressure steadily to the manufacturer's cut-out setting, and the low-pressure warning must come on close to the manufacturer's setting when you drain the air by pressing the brake pedal with the engine stopped.
For hydraulic brakes, pump the pedal three times, then push firmly and hold for five seconds — a pedal that sinks means a leak, and the vehicle must not be driven until it is fixed.
The parking (spring) brake on an air-braked vehicle must hold the stationary truck on its own; the service brake is tested by moving forward in first gear at no more than 5 km/h and braking firmly.
After about an hour of driving, stop in a safe place and check the load, walk around the vehicle, feel tyres and brake drums for heat, and look for leaks; repeat at every stop.
Last updated: October 2026
Why two brake systems need two check routines
A heavy rigid truck is fitted with one of two braking systems. Each system stores and applies braking force differently, so the daily check routine is different. The Victorian Heavy Rigid test asks you to know which checks belong to which system and what reading or behaviour is acceptable.
Check item Air brake system Hydraulic brake system
Energy storage Compressed air in reservoirs, built up to the manufacturer's cut-out setting Incompressible brake fluid in master cylinder and lines
Build-up check (engine on) Gauge shows a steady increase to the manufacturer's cut-out setting; the warning buzzer sounds until pressure reaches the manufacturer's setting (if the tank started low) No build-up test
Low-pressure warning With the engine stopped, press the pedal repeatedly: the buzzer and/or light must come on close to the manufacturer's setting; must not be disabled No low-pressure warning device; fluid-level warning light (if fitted) must go out after start
Pedal hold test Apply service brake several times to drain reservoirs and confirm the warning activates; then rebuild Pump the pedal three times, then push firmly and hold for five seconds; a sinking pedal means a leak in the system
Fluid / air inspection Drain a small amount from each reservoir to check for water and oil contamination Check fluid level at reservoir between MIN and MAX; inspect for leaks at callipers, wheel cylinders, master cylinder
Parking brake Spring brakes apply automatically on air loss; must hold the vehicle on the parked gradient Mechanical park brake (hand or foot applied); must hold on the parked gradient
Hose / pipe inspection Air lines and fittings must be secure, not chafed, cracked, kinked, or leaking; glad-hand seals intact (if towing) Hydraulic hoses must not swell, crack, chafe, or leak; no fluid at fittings
Brake fade risk Air delay through long lines (longer on combinations); retarder usually fitted Hydraulic application is near-instant on a rigid; less air-delay risk but fluid boil can cause fade on long descents
Air brake pre-departure checks (step by step)
Drain the reservoirs. With the engine off and the parking brake applied, briefly open each reservoir drain valve to eject water and oil that have condensed overnight. Close the valves. If more than a trace of water or oil comes out, report it — the air dryer or compressor may be passing oil.
Start and build pressure. With the engine at fast idle, watch the dash gauge. Pressure should rise steadily to the cut-out setting in the manufacturer's handbook. The compressor should stop loading at cut-out.
Test the low-pressure warning. With the engine off, fan the service brake pedal to drain the reservoirs. The low-pressure warning buzzer and light must come on close to the manufacturer's setting. The warning must not be bypassed or muted.
Test the spring (parking) brake. With the park-brake control out and the system at full pressure, place the transmission in gear and gently attempt to move. The spring brake must hold the truck. Then push the park-brake control in (release) and confirm the truck can move normally.
Test the service brake. In first gear, moving forward at no more than 5 km/h in a safe area, apply the service brake firmly. The pedal should feel firm with normal travel, the truck should pull up straight, and there should be no unusual noise, pulling, or delayed response.
Check the ABS warning. Turn the ignition on; the ABS warning lamp should come on and then go out as the system completes its self-check (see the vehicle handbook). A lamp that stays on indicates an ABS fault — the service brake still works but ABS is disabled and the defect must be reported.
Hydraulic brake pre-departure checks (step by step)
Check fluid level. With the engine off, confirm the brake-fluid reservoir is between MIN and MAX. Use the correct DOT-rated fluid specified by the manufacturer. A low level with no visible external leak may indicate worn friction material — have it investigated before topping up.
Inspect for leaks. Look at the master cylinder, along each hydraulic hose, and at each wheel cylinder or calliper. Any wetness at a fitting or a soft, swollen hose is a defect.
Pedal hold test. Pump the brake pedal three times. Then push it firmly and hold it down for five seconds. The pedal must not sink. The handbook says a sinking pedal means there is a leak in the system — have it fixed before driving.
Assisted pedal feel. Start the engine; the pedal should drop slightly as the vacuum or hydraulic servo assist engages, then feel firm. A pedal that feels hard with the engine on (loss of assist) or that feels spongy (air in the fluid) is a defect.
Parking brake. Apply the mechanical park brake. With the transmission in gear, gently attempt to move. The park brake must hold. Release it and confirm the brake-warning lamp extinguishes.
Service brake. In first gear at no more than 5 km/h in a safe area, apply the service brake firmly. The truck must stop in a straight line without pulling, unusual noise, or excessive pedal travel.
After-departure inspection
Early in a trip a load can settle, a brake can drag, or a slow leak can show up. The handbook's after-departure routine is: visually check that the load is secure using all your mirrors, and after you have driven for about an hour, stop in a safe spot away from the traffic flow and repeat a quick check around the vehicle. Each time you stop, repeat the after-departure checks before continuing.
After-departure checks
Visual load check. Walk around the load. Confirm restraint equipment (chains, straps, turnbuckles, twist locks) is still tight and correctly seated; the load has not shifted, settled, or leaked; and the tailgate, doors, and curtains are secure.
Tyre temperature by touch. Carefully place the back of your hand near (not on) each wheel after the first few kilometres. All wheels on the same axle should be at a similar temperature. A noticeably hotter wheel indicates a dragging brake, a tight wheel bearing, or under-inflation — investigate before continuing. A cold wheel on an axle where the others are warm can indicate a brake that is not working at all.
Brake drum / disc temperature. Hotter-than-expected drums or discs on one side point to uneven brake adjustment or a dragging brake. This is a common early sign of an air-system leak at a chamber or a stuck slack adjuster.
Air system leak check (air-braked vehicles). With the engine off and the parking brake applied, watch the dash air-pressure gauge for one minute. Pressure must not drop by more than the manufacturer-specified amount. The handbook says to note any pressure lost since the last stop and fix a problem like this before driving.
Hydraulic system leak check. Look under the truck for any new fluid. Re-check the master-cylinder reservoir level. A drop in level with no visible external leak may indicate an internal master-cylinder fault.
Underbody and load area. Re-scan for new fluid pools, a shifted load, loose equipment, or anything hanging underneath the vehicle.
Mirrors and lights. A quick re-check that mirrors are still adjusted, lights are still working (reflection on the road behind, or a helper), and the windscreen is not smeared.
If anything found at the after-departure stop is a safety defect — a leaking air chamber, a shifted load, a brake drum hot enough to smell hot brake — the driver must stop and arrange repair or re-restraint before continuing. Continuing with a known defect is a Primary Duty breach under HVNL s26C.