Study guide
Pre-Operational Daily Checks: Cabin, Engine, Tyres, Brakes, and Lights
VicRoads Heavy Vehicle Knowledge Test — Rigid KT4
Track your progress as you read
Finished sections get a check mark.
1 Victorian Road Rules — Driver Obligations
Speed Limits for Heavy Vehicles in Victoria Zero BAC and Roadside Drug Testing for Heavy Vehicle Drivers Seatbelts, Parking Restrictions, and Night-Time Clearance Lighting Railway Crossing Procedures for Buses and Heavy Vehicles
2 Victorian Road Rules — Road Situations and Chain of Responsibility
Portable Warning Triangles: Carriage, Placement, and AS 3790 Following Distances, Lane Changes, and Turn Procedures for Long Vehicles Chain of Responsibility, Weighbridge Stops, and Enforcement Powers
3 Heavy Vehicle Law, Dimensions, and Access
Heavy Vehicle Licence Classes and Transmission Restrictions Mass and Dimension Limits for Rigid Vehicles Heavy Vehicle Road Signs, Access Restrictions, and Oversize/Overmass Permits
4 Vehicle Inspections and Roadworthiness
Pre-Operational Daily Checks: Cabin, Engine, Tyres, Brakes, and Lights Air Brake vs Hydraulic Brake System Checks and After-Departure Inspection Defect Identification, Roadworthiness Obligations, and Regular Mechanical Inspections
5 Vehicle Control, Braking, and Gear Selection
Double-Clutching and Gear Selection for Non-Synchromesh Gearboxes Braking Systems, Brake Fade, Stopping Distances, and Air Brake Delay Off-Tracking, Rollover Risk, Crash Avoidance Space, and Skid Correction
6 Load Restraint and Load Rules
6.1 Load Restraint Performance Standards 6.2 Tie-down vs Direct Restraint Methods 6.3 Load Placement, Distribution, Overhang Limits, and Load Security Checks
7 Fatigue Management and Work Diary
Standard Hours, BFM, AFM and ACH: Work/Rest Options and Fatigue-Regulated Vehicles National Driver Work Diary: Requirements, Completion, Record-Keeping, and Fatigue Prevention
8 Coupling and Combination Vehicle Rules
Coupling and Uncoupling: Procedures, Air Lines, Trailer Park Brake, Roll-Away Confirmation, and HC Licence Threshold
Pre-Operational Daily Checks: Cabin, Engine, Tyres, Brakes, and Lights
Key Takeaways Explain This Topic AI
A daily pre-operational check is a quick visual inspection carried out before leaving the yard, depot, or rest area, and it complements (but does not replace) scheduled maintenance.
Use the same routine every day; the handbook's order is a walk-around outside the vehicle, engine checks, then the driver's controls, gauges and brake tests.
Tyres on a heavy rigid vehicle must have at least 1.5 mm tread depth in the principal groove across at least 75% of the tyre width in a continuous band around the whole circumference.
A fault found during the daily check that affects safety must be reported and the vehicle repaired before it is driven; an unrepaired defective heavy vehicle must not be used on a road.
Last updated: October 2026
Why a daily check is a legal requirement, not a formality
Under the Heavy Vehicle National Law (HVNL) , which applies in Victoria through the Heavy Vehicle National Law Application Act 2013 (Vic), every heavy vehicle used on a road must comply with the heavy vehicle standards — the Australian Design Rules (ADRs) and the Heavy Vehicle (Vehicle Standards) National Regulation. The handbook is blunt: "It does not matter who maintains the vehicle, it is the driver's responsibility if the vehicle is unroadworthy," and fines for vehicle defects are payable by the driver as well as the vehicle's owner. Operators and the other parties in the Chain of Responsibility also have a Primary Duty under HVNL s. 26C to ensure, so far as is reasonably practicable, the safety of their transport activities.
The NHVR publishes the Guide to creating heavy vehicle daily checks , which lists the items and areas that may be covered in a quick visual inspection undertaken prior to leaving the yard, depot, or rest area . A daily check does not replace scheduled maintenance; it catches the defects that develop between services — a slow air leak, a chafed tyre, a blown brake-light globe — before they become a major defect on the road.
The check must be recorded . Most Victorian operators use a written or electronic daily-check sheet that the driver signs and dates; the completed sheet becomes part of the operator's maintenance records. If an authorised officer or a Transport Safety Officer stops the truck, a current, signed daily check is good evidence that the driver and operator have done their part.
The full daily-check sequence
The sequence below follows the handbook's order: around the vehicle, engine checks, then the driver's controls and brake tests. Do the checks in the same order every day so that nothing is missed.
1. Around-vehicle walk-around (before opening the bonnet)
Walk clockwise around the whole vehicle so you face oncoming traffic on the road side.
Look for body damage, loose panels, missing mudguards or mudflaps, and rear marking plates (mandatory on vehicles > 12 tonne GVM) that are faded, torn, or missing.
Check that conspicuity (reflective contour) tape is present and clean where the vehicle is required to display it.
Inspect the load area: tailgate or barn doors closed and latched, load restraint equipment (chains, straps, turnbuckles) stowed or correctly fitted, no loose debris or unsecured items on the deck.
Look underneath for fluid pools — oil, coolant, fuel, or brake fluid — that indicate a leak developed overnight.
2. Tyres and wheels
Walk around every axle group. For a rigid truck this includes the steer axle and every drive and tag-axle wheel.
Measure tread depth in the principal grooves. The NHVIM minimum is 1.5 mm in a continuous band around the whole circumference and across at least 75% of the tyre width . Most operators use a 2 mm internal trigger so the tyre is not borderline by the next check.
Inspect each tyre for cuts that expose cords or wire, chunking, bulges, bumps, ply separations, embedded objects, and signs of carcass failure. Any of these is a major defect — the tyre must not be driven on.
Confirm dual tyres do not contact each other and that nothing is trapped between them (stones, debris).
Inspect wheels and rims for cracks, buckles, elongated stud holes, and loose or missing wheel nuts. On a wheel with visible studs, check for any nut that has backed off — look for rust streaks radiating from a nut, which is a sign it is loosening.
Confirm tyres match the manufacturer's tyre placard (size, load rating, speed rating of at least 100 km/h) and that re-grooving is only present on tyres marked suitable for re-grooving.
3. Engine bay (with the engine off, bonnet or cab tilted)
Check engine oil level on the dipstick; top up if below the low mark. Look for coolant, power-steering fluid, and (for air-braked vehicles) the air-compressor governor cut-in range.
Inspect coolant level at the overflow reservoir (never open a hot pressurised radiator cap).
Inspect belts (fan, alternator, air-compressor, power-steering) for correct tension, cracking, fraying, glazing, or oil contamination.
Inspect hoses for swelling, softening, cracking, chafing, or leaks, especially where a hose contacts a moving part or heat source.
Check the battery is secured, terminals are clean and tight, and the isolation switch (where fitted) functions.
Check the fuel system : fuel cap present and sealing, no leaks, fuel lines not contacting moving or hot parts.
Check the exhaust is securely mounted, not leaking, and not directing gases onto brake lines, hoses, or the load.
4. Cabin drill and controls
Adjust the seat so you can fully depress the brake and clutch pedals without stretching.
Fasten the seatbelt and check it is not frayed, cut, or twisted.
Adjust the mirrors; confirm each mirror is clean, not cracked, deteriorated, or obscured.
Check the windscreen for cracks, stars, or damage that impairs vision within the swept area of the wipers; confirm wiper blades are intact and the washer reservoir is full.
Confirm the horn works, the demister and windscreen demist function, and the speedometer and odometer are illuminated and legible.
Confirm the registration label/disc is current and the number plates are clean, visible, and illuminated.
5. Brakes
The brake check differs for air and hydraulic systems; the detailed comparison is in Section 4.2. At the daily-check stage the driver confirms:
Brake pedal has an anti-slip surface, is not broken or missing, and has normal travel before firm resistance.
Park brake engages and holds the vehicle on the gradient it is parked on.
Air-braked vehicles: the air pressure gauge shows a steady increase up to the manufacturer's cut-out setting; with the engine stopped and the brake pedal pressed repeatedly, the low-pressure warning buzzer/light comes on close to the manufacturer's setting; any pressure lost since the last stop is noted and fixed before driving; the air tank drain taps are opened to check for water and oil, then closed.
Hydraulic-braked vehicles: brake fluid level at the reservoir is between MIN and MAX; no fluid leaks at callipers, wheel cylinders, or master cylinder; the pedal does not sink — the handbook's test is to pump the pedal three times, push it firmly and hold it for five seconds; a sinking pedal means a leak in the system.
Brake hoses and pipes are securely clipped, not cracked, kinked, chafed, bulging, or heat-damaged, and do not leak.
Brake drums and discs are fitted, not cracked, and not missing pieces; friction material is not contaminated with oil, grease, or brake fluid.
6. Lights and reflectors
With the ignition on and a helper (or by checking reflections against a wall), confirm:
Headlights (white) — low and high beam both work.
Tail lights (red), brake lights (red), and reversing lights (white).
Direction indicators (yellow) front and rear, and side-repeaters where fitted.
Clearance and end-outline marker lights — white or yellow to the front, red to the rear — so the full width and height of the vehicle is visible at night.
Side marker lights (yellow to front half, red to rear half) on vehicles over 2.2 m wide.
Number-plate light illuminates the rear plate.
Reflectors — red to the rear, yellow to the side, white or yellow to the front — are present, the correct colour, and not cracked or faded.
Lenses are securely mounted, not cracked, faded, or letting in moisture or dirt.
If any mandatory light or reflector is inoperative and cannot be repaired before departure, the vehicle is not roadworthy.