Study guide

4.3 Aerodynamics: Lift, Drag, Thrust, Weight and Energy

CASA Remote Pilot Licence RePL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the RePL Exam 1.2 How to Use This Guide & Build a Study Plan

2 RPA Air Law: Regulatory Framework & Standard Operating Conditions

2.1 CASR Part 101 and the Manual of Standards 2.2 Standard Operating Conditions (SOC) 2.3 The 120 m (400 ft) AGL Height Limit 2.4 VLOS, Daylight, Visibility and the One-RPA Rule

3 RPA Air Law: Licensing, Categories & Approvals

3.1 RePL vs ReOC: Pilot Licence vs Operator Certificate 3.2 Excluded Categories and Operator Accreditation 3.3 RPA Weight Categories and Registration 3.4 Operating Beyond the SOC: Approvals and the ReB1

4 Basic Aviation Knowledge (RBAK)

4.1 Direction, Wind Velocity and Aviation Time 4.2 Units of Measurement: Height, Altitude and Elevation 4.3 Aerodynamics: Lift, Drag, Thrust, Weight and Energy 4.4 Weight and Balance: Terms and Limits 4.5 Propellers and Rotors 4.6 Axes, Attitude and Flight Control Principles 4.7 The Remote Pilot Station

5 RPAS Systems: Platforms, C2 Link & Power

5.1 Multirotor vs Fixed-Wing Characteristics 5.2 Command-and-Control Link and Failsafes 5.3 Lithium-Polymer Battery Management and Safety

6 RPAS Systems: Sensors, Payload & Preflight

6.1 GNSS, Compass, IMU and Geofencing 6.2 Payload, Centre of Gravity and Pre-Flight Checks 6.3 Automated Flight Management Systems (RAFM)

7 Electrical & Electronic Systems (REES)

7.1 Electrical Terms and RPAS Electrical Components 7.2 Electric Motors, Kv and Current Draw 7.3 Battery Types, Specifications and Dangerous Goods 7.4 Charging, Discharging, Balancing and Battery Limitations 7.5 Radio Waves, Frequency Bands and Propagation 7.6 GPS Components, Errors and Electromagnetic Hazards

8 Multirotor Aerodynamics & Performance (RBKM)

8.1 Multirotor Airframe and Component Layout 8.2 Rotor Aerodynamics: Blade Design, Thrust, Drag and Torque 8.3 Hovering: Ground Effect, Recirculation and Translational Lift 8.4 Multirotor Flight Controls, Stabilisation and GPS Hold 8.5 Motor Failure, Rotor Direction and Abnormal Aerodynamics 8.6 Weight, Power, Wind and Climb Performance 8.7 Descent, Vortex Ring State and Landing

9 Navigation & Charts

9.1 Chart Fundamentals: Latitude, Longitude, Variation and Distance 9.2 Visual Terminal Charts and Visual Navigation Charts 9.3 Airspace Classes, Control Zones and CTA Steps 9.4 Restricted, Danger and Prohibited Areas and Obstacles 9.5 NOTAMs, the AIP and Chart Currency

10 Meteorology

10.1 Wind, Sea Breezes and Local Effects 10.2 Turbulence, Orographic Effects and Terrain 10.3 Thunderstorms, Fronts and Fog 10.4 Density Altitude, METAR/TAF and BoM Forecasts 10.5 Weather Observations: Reading the Sky and the Site

11 Human Factors

11.1 IMSAFE, Fatigue and Complacency 11.2 Situational Awareness, Fixation and External Pressure 11.3 Alcohol, Drugs and Crew Resource Management 11.4 Vision, Visual Limitations and Illusions 11.5 Stress and Stress Management 11.6 Threat and Error Management

12 Radio & AROC

12.1 Phonetic Alphabet, Phraseology and CTAF 12.2 The 121.5 MHz Emergency Frequency, Transponder Codes and the AROC

13 Risk & Operational Procedures

13.1 Job Safety Assessment, Risk Assessment and the Hierarchy of Controls 13.2 Site Survey, Bystander Management, Emergencies and Giving Way

14 Operations, Airworthiness & Reporting (RKOP)

14.1 Remote Pilot Responsibilities, Crew Briefing and Ground Operations 14.2 Operational, Remote Pilot and Technical Logs 14.3 Airworthiness, Serviceability and Defect Reporting 14.4 Role Equipment, Sensors and Payload Implications 14.5 Accident and Incident Reporting to the ATSB 14.6 Abnormal Operations, Fail-Safes and Flight Termination 14.7 Operating Near Aerodromes and Above 400 ft AGL

4.3 Aerodynamics: Lift, Drag, Thrust, Weight and Energy

Key Takeaways Explain This Topic AI

The four forces are lift, weight, thrust and drag; in a steady hover a multirotor's rotor thrust acts as lift and exactly balances weight.

Angle of attack is the angle between the aerofoil chord line and the relative airflow, and lift rises with angle of attack only up to the stalling angle.

Total drag is the sum of parasite drag, which rises with the square of airspeed, and induced drag, which falls as airspeed rises.

Potential energy is height, kinetic energy is speed, and inertia resists change — which is why a heavy RPA takes longer to stop and hits harder.

Last updated: August 2026

The Four Forces

Every aircraft, crewed or remotely piloted, is acted on by four forces:

Lift — the force that opposes weight and holds the aircraft up.

Weight — the force of gravity acting through the centre of gravity .

Thrust — the force that drives the aircraft forward (or, on a multirotor, upward).

Drag — the force that resists motion through the air.

In steady, unaccelerated flight lift equals weight and thrust equals drag. A multirotor collapses two of these into one: the rotors produce a thrust vector, and in a hover that vector points straight up and is the lift. Tilt the airframe and the same thrust splits into a vertical component that still has to equal weight and a horizontal component that produces forward motion — which is why a multirotor must add power when it accelerates, and why a strongly tilted multirotor in a high wind is close to its performance ceiling.

Aerofoil Terminology

Schedule 4 topic 5(a) asks for a specific vocabulary.

Aerofoil — a shaped surface, such as a wing or rotor blade, designed to produce lift when air flows over it.

Chord line — the straight line from the aerofoil's leading edge to its trailing edge.

Relative airflow — the airflow as experienced by the aerofoil, equal and opposite to the direction of the aerofoil's motion through the air.

Angle of attack — the angle between the chord line and the relative airflow . This is not the same as pitch attitude, which is measured against the horizon.

Centre of pressure — the single point through which the total lift force is considered to act.

Centre of gravity — the single point through which the total weight is considered to act.

As angle of attack increases, lift increases — but only up to the critical (stalling) angle , typically around 15 to 16 degrees for a conventional aerofoil. Beyond it the airflow separates from the upper surface, lift drops sharply and drag rises. A fixed-wing RPA stalls at the same angle of attack every time regardless of speed or weight; what changes is the speed at which that angle is reached.

Two Explanations of Lift, Both Correct

Schedule 4 names three principles by name, so know all three:

Bernoulli's principle — where a fluid speeds up, its static pressure falls. Air accelerating over the curved upper surface of an aerofoil is at lower pressure than the slower air beneath, and the pressure difference produces lift.

Newton's third law — every action has an equal and opposite reaction. The aerofoil deflects a mass of air downwards; the reaction pushes the aerofoil upwards. On a multirotor this is the more intuitive description: the rotors throw air down, and the aircraft goes up.

The Coandă effect — a fluid jet tends to stay attached to a curved surface. It explains why the airflow follows the aerofoil's upper camber rather than separating immediately.

These are not competing theories to choose between. They are three descriptions of the same physical event, and an exam answer that says lift comes from both the pressure difference and the reaction to deflected air is the correct one.

Drag: Two Families

Total drag is the sum of two components that behave in opposite ways with airspeed.

Parasite drag is everything that is not a by-product of producing lift. Schedule 4 breaks it into:

Form drag — resistance caused by the shape of the body pushing through the air (a landing-gear leg, a camera gimbal, a squared-off battery pack).

Skin friction — resistance from air rubbing along the surface.

Interference drag — extra drag generated where two components meet, such as an arm joining the centre body, because their airflows interact.

Parasite drag rises with the square of airspeed: double the speed and parasite drag quadruples.

Induced drag is the unavoidable by-product of producing lift. Generating lift leaves the air behind the aerofoil with downward momentum and trailing vortices, and the energy that goes into that wake appears as drag. Induced drag is greatest at low speed and high angle of attack , and it falls as speed rises.

  • Airspeed Parasite drag Induced drag Total drag
  • Low Small Large High
  • Best endurance/range speed Moderate Moderate Minimum
  • High Large Small High

Because the two curves move in opposite directions, total drag is a U-shape with a minimum somewhere in the middle. That minimum is why a fixed-wing RPA has a specific best-endurance airspeed rather than simply flying as slowly as possible, and why a mapping mission flown too slowly can burn more battery than the same mission flown at the recommended cruise.

Energy and Inertia

Schedule 4 topic 4 asks for three terms:

Potential energy — energy stored by virtue of height. An RPA at 120 m AGL holds more potential energy than the same aircraft at 20 m.

Kinetic energy — energy of motion, given by K E = 1 2 m v 2 KE = \tfrac{1}{2}mv^{2} K E = 2 1 ​ m v 2 where m is mass and v is velocity.

Inertia — the tendency of a body to resist a change in its state of motion. Mass is the measure of inertia.

The kinetic-energy formula is the reason CASA's whole regulatory structure is built on weight categories . Because velocity is squared, doubling the speed quadruples the energy; because mass is linear, doubling the mass only doubles it. But mass sets the floor. A 250 g micro RPA striking a person at 15 m/s carries about 28 joules. A 2 kg drone at the same speed carries about 225 joules — eight times the energy for eight times the mass. A 25 kg small RPA carries about 2,800 joules. That progression, not an arbitrary line, is why micro RPA get concessions the small category does not.

Inertia has a handling consequence too. A heavier RPA accelerates more slowly, decelerates more slowly, and needs more room to stop. A pilot flying a 7 kg aircraft toward an obstacle at the same closure rate they are used to on a 900 g aircraft will run out of stopping distance. Plan the deceleration point by aircraft mass, not by habit.