Study guide

4.2 Units of Measurement: Height, Altitude and Elevation

CASA Remote Pilot Licence RePL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the RePL Exam 1.2 How to Use This Guide & Build a Study Plan

2 RPA Air Law: Regulatory Framework & Standard Operating Conditions

2.1 CASR Part 101 and the Manual of Standards 2.2 Standard Operating Conditions (SOC) 2.3 The 120 m (400 ft) AGL Height Limit 2.4 VLOS, Daylight, Visibility and the One-RPA Rule

3 RPA Air Law: Licensing, Categories & Approvals

3.1 RePL vs ReOC: Pilot Licence vs Operator Certificate 3.2 Excluded Categories and Operator Accreditation 3.3 RPA Weight Categories and Registration 3.4 Operating Beyond the SOC: Approvals and the ReB1

4 Basic Aviation Knowledge (RBAK)

4.1 Direction, Wind Velocity and Aviation Time 4.2 Units of Measurement: Height, Altitude and Elevation 4.3 Aerodynamics: Lift, Drag, Thrust, Weight and Energy 4.4 Weight and Balance: Terms and Limits 4.5 Propellers and Rotors 4.6 Axes, Attitude and Flight Control Principles 4.7 The Remote Pilot Station

5 RPAS Systems: Platforms, C2 Link & Power

5.1 Multirotor vs Fixed-Wing Characteristics 5.2 Command-and-Control Link and Failsafes 5.3 Lithium-Polymer Battery Management and Safety

6 RPAS Systems: Sensors, Payload & Preflight

6.1 GNSS, Compass, IMU and Geofencing 6.2 Payload, Centre of Gravity and Pre-Flight Checks 6.3 Automated Flight Management Systems (RAFM)

7 Electrical & Electronic Systems (REES)

7.1 Electrical Terms and RPAS Electrical Components 7.2 Electric Motors, Kv and Current Draw 7.3 Battery Types, Specifications and Dangerous Goods 7.4 Charging, Discharging, Balancing and Battery Limitations 7.5 Radio Waves, Frequency Bands and Propagation 7.6 GPS Components, Errors and Electromagnetic Hazards

8 Multirotor Aerodynamics & Performance (RBKM)

8.1 Multirotor Airframe and Component Layout 8.2 Rotor Aerodynamics: Blade Design, Thrust, Drag and Torque 8.3 Hovering: Ground Effect, Recirculation and Translational Lift 8.4 Multirotor Flight Controls, Stabilisation and GPS Hold 8.5 Motor Failure, Rotor Direction and Abnormal Aerodynamics 8.6 Weight, Power, Wind and Climb Performance 8.7 Descent, Vortex Ring State and Landing

9 Navigation & Charts

9.1 Chart Fundamentals: Latitude, Longitude, Variation and Distance 9.2 Visual Terminal Charts and Visual Navigation Charts 9.3 Airspace Classes, Control Zones and CTA Steps 9.4 Restricted, Danger and Prohibited Areas and Obstacles 9.5 NOTAMs, the AIP and Chart Currency

10 Meteorology

10.1 Wind, Sea Breezes and Local Effects 10.2 Turbulence, Orographic Effects and Terrain 10.3 Thunderstorms, Fronts and Fog 10.4 Density Altitude, METAR/TAF and BoM Forecasts 10.5 Weather Observations: Reading the Sky and the Site

11 Human Factors

11.1 IMSAFE, Fatigue and Complacency 11.2 Situational Awareness, Fixation and External Pressure 11.3 Alcohol, Drugs and Crew Resource Management 11.4 Vision, Visual Limitations and Illusions 11.5 Stress and Stress Management 11.6 Threat and Error Management

12 Radio & AROC

12.1 Phonetic Alphabet, Phraseology and CTAF 12.2 The 121.5 MHz Emergency Frequency, Transponder Codes and the AROC

13 Risk & Operational Procedures

13.1 Job Safety Assessment, Risk Assessment and the Hierarchy of Controls 13.2 Site Survey, Bystander Management, Emergencies and Giving Way

14 Operations, Airworthiness & Reporting (RKOP)

14.1 Remote Pilot Responsibilities, Crew Briefing and Ground Operations 14.2 Operational, Remote Pilot and Technical Logs 14.3 Airworthiness, Serviceability and Defect Reporting 14.4 Role Equipment, Sensors and Payload Implications 14.5 Accident and Incident Reporting to the ATSB 14.6 Abnormal Operations, Fail-Safes and Flight Termination 14.7 Operating Near Aerodromes and Above 400 ft AGL

4.2 Units of Measurement: Height, Altitude and Elevation

Key Takeaways Explain This Topic AI

Height is measured above a specified datum such as ground level, altitude is measured above mean sea level, and elevation is the height of a fixed point on the surface above mean sea level.

The 400 ft (120 m) RPA limit is a HEIGHT above the surface directly below the aircraft, while charted airspace bases and terrain figures are ALTITUDES and ELEVATIONS above mean sea level.

Australian aviation mixes units by quantity: feet for vertical distance, nautical miles for horizontal distance, knots for speed, metres for visibility, degrees Celsius for temperature and hectopascals for pressure.

Converting between AGL and AMSL is a single addition or subtraction using the charted terrain elevation, and it is the step candidates most often skip.

Last updated: August 2026

Three Words That Are Not Synonyms

Schedule 4 gives units of measurement a priority- A code, and the first thing it asks for is the difference between height , altitude and elevation . In everyday speech these are interchangeable. In aviation they are three distinct quantities with three different datums, and confusing them puts an RPA into controlled airspace.

Term Measured from Typical use

Height A specified datum — for RPA purposes, the surface directly below the aircraft "400 ft AGL", the RPA operating limit

Altitude Mean sea level (MSL) "1,500 ft AMSL", a controlled-airspace step base or a crewed aircraft's level

Elevation Mean sea level, but for a fixed point on the ground "Aerodrome elevation 340 ft", terrain contours on a chart

Two abbreviations do the work. AGL — above ground level — is a height. AMSL — above mean sea level — is an altitude; MSL and AMSL are used interchangeably in Australian practice.

The regulatory consequence is immediate. CASR 101.085 limits an RPA to 400 ft above ground level , "that is, above the point on the surface of the water or earth directly below the RPA". That is a height. A Visual Terminal Chart, by contrast, prints airspace step bases and terrain figures in feet AMSL . The two numbers cannot be compared until one is converted.

The conversion Altitude (AMSL) = Terrain elevation (AMSL) + Height (AGL) \text{Altitude (AMSL)} = \text{Terrain elevation (AMSL)} + \text{Height (AGL)} Altitude (AMSL) = Terrain elevation (AMSL) + Height (AGL) Height (AGL) = Altitude (AMSL) − Terrain elevation (AMSL) \text{Height (AGL)} = \text{Altitude (AMSL)} - \text{Terrain elevation (AMSL)} Height (AGL) = Altitude (AMSL) − Terrain elevation (AMSL)

Worked example. You plan to operate at the standard 400 ft AGL over terrain charted at 900 ft AMSL. Your aircraft will be at 900 + 400 = 1,300 ft AMSL . The chart shows a controlled-area step with a base of 1,200 ft AMSL over that point. Your flight is above the step base and therefore inside controlled airspace — even though you never exceeded 400 ft AGL. This is not hypothetical: it is why airspace planning for an RPA has to be done in AMSL even though the operating limit is in AGL.

Reverse example. A chart shows a CTA base of 2,500 ft AMSL over terrain of 1,100 ft AMSL. The base is 2,500 − 1,100 = 1,400 ft AGL , comfortably above a 400 ft AGL operation, so the step is not a constraint at that point.

The Units Australia Uses

Australian aviation deliberately mixes metric and imperial, assigning a unit to each quantity rather than adopting one system throughout. Schedule 4 topic 3(b) lists the quantities; the table below gives the Australian answer for each.

Quantity Unit Notes

Vertical distance (height, altitude, elevation) Feet (ft) CASA states the RPA limit as 400 ft, with 120 m as the metric equivalent

Horizontal distance Nautical miles (NM) 1 NM = 1.852 km; short distances near aerodromes are often given in kilometres or metres

  • Speed Knots (kt) 1 knot = 1 NM per hour ≈ 1.852 km/h
  • Visibility Metres and kilometres A METAR reports 9999 for 10 km or more
  • Temperature Degrees Celsius (°C) METARs report temperature and dew point as whole degrees
  • Atmospheric pressure Hectopascals (hPa) QNH is a four-figure group, e.g. Q1013
  • Weight Kilograms (kg) and grams (g) RPA weight categories are defined in grams and kilograms
  • Conversions worth knowing cold

400 ft = 121.9 m. CASA rounds this to 120 m in public material, so a 120 m limit and a 400 ft limit are the same rule stated twice. Take the more restrictive of the two if a question forces a choice.

1 NM = 1.852 km. So 3 NM = 5.556 km , which CASA rounds to the familiar 5.5 km aerodrome buffer. Again, one rule, two statements.

1 m ≈ 3.28 ft. A 45 m micro-RPA ceiling near an aerodrome is roughly 148 ft.

1 kt ≈ 0.514 m/s. A 15-knot wind is about 7.7 m/s — useful because many drone manufacturers publish maximum wind resistance in metres per second while forecasts are in knots.

12 NM ≈ 22 km , the offshore limit of Australian territory quoted in the standard operating conditions.

That last conversion pair is the one to rehearse. A manufacturer specifying "maximum wind resistance 10 m/s" is quoting roughly 19.4 knots . If the forecast is 27018G26KT , the 26-knot gust is well past the aircraft's limit even though the mean of 18 knots is inside it.

Where This Shows Up in the Exam

Expect three shapes of question:

Definition questions — "which of these is measured from mean sea level?" The answer set separates height from altitude from elevation.

Conversion questions — you are given a terrain elevation and an operating height and asked for the AMSL figure, or given an AMSL airspace base and asked whether a 400 ft AGL flight is below it.

Unit-matching questions — you are given a value with a missing unit and asked which unit is correct for that quantity, or asked to convert a manufacturer's metric limit into the knots used by a forecast.

The habit that protects you in all three: write the datum next to every number . 400 AGL and 1,300 AMSL are unambiguous. 400 and 1,300 are not, and an unlabelled number is how an otherwise competent pilot ends up comparing a height with an altitude.