Study guide
4.4 Weight and Balance: Terms and Limits
CASA Remote Pilot Licence RePL
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the RePL Exam 1.2 How to Use This Guide & Build a Study Plan
2 RPA Air Law: Regulatory Framework & Standard Operating Conditions
2.1 CASR Part 101 and the Manual of Standards 2.2 Standard Operating Conditions (SOC) 2.3 The 120 m (400 ft) AGL Height Limit 2.4 VLOS, Daylight, Visibility and the One-RPA Rule
3 RPA Air Law: Licensing, Categories & Approvals
3.1 RePL vs ReOC: Pilot Licence vs Operator Certificate 3.2 Excluded Categories and Operator Accreditation 3.3 RPA Weight Categories and Registration 3.4 Operating Beyond the SOC: Approvals and the ReB1
4 Basic Aviation Knowledge (RBAK)
4.1 Direction, Wind Velocity and Aviation Time 4.2 Units of Measurement: Height, Altitude and Elevation 4.3 Aerodynamics: Lift, Drag, Thrust, Weight and Energy 4.4 Weight and Balance: Terms and Limits 4.5 Propellers and Rotors 4.6 Axes, Attitude and Flight Control Principles 4.7 The Remote Pilot Station
5 RPAS Systems: Platforms, C2 Link & Power
5.1 Multirotor vs Fixed-Wing Characteristics 5.2 Command-and-Control Link and Failsafes 5.3 Lithium-Polymer Battery Management and Safety
6 RPAS Systems: Sensors, Payload & Preflight
6.1 GNSS, Compass, IMU and Geofencing 6.2 Payload, Centre of Gravity and Pre-Flight Checks 6.3 Automated Flight Management Systems (RAFM)
7 Electrical & Electronic Systems (REES)
7.1 Electrical Terms and RPAS Electrical Components 7.2 Electric Motors, Kv and Current Draw 7.3 Battery Types, Specifications and Dangerous Goods 7.4 Charging, Discharging, Balancing and Battery Limitations 7.5 Radio Waves, Frequency Bands and Propagation 7.6 GPS Components, Errors and Electromagnetic Hazards
8 Multirotor Aerodynamics & Performance (RBKM)
8.1 Multirotor Airframe and Component Layout 8.2 Rotor Aerodynamics: Blade Design, Thrust, Drag and Torque 8.3 Hovering: Ground Effect, Recirculation and Translational Lift 8.4 Multirotor Flight Controls, Stabilisation and GPS Hold 8.5 Motor Failure, Rotor Direction and Abnormal Aerodynamics 8.6 Weight, Power, Wind and Climb Performance 8.7 Descent, Vortex Ring State and Landing
9 Navigation & Charts
9.1 Chart Fundamentals: Latitude, Longitude, Variation and Distance 9.2 Visual Terminal Charts and Visual Navigation Charts 9.3 Airspace Classes, Control Zones and CTA Steps 9.4 Restricted, Danger and Prohibited Areas and Obstacles 9.5 NOTAMs, the AIP and Chart Currency
10 Meteorology
10.1 Wind, Sea Breezes and Local Effects 10.2 Turbulence, Orographic Effects and Terrain 10.3 Thunderstorms, Fronts and Fog 10.4 Density Altitude, METAR/TAF and BoM Forecasts 10.5 Weather Observations: Reading the Sky and the Site
11 Human Factors
11.1 IMSAFE, Fatigue and Complacency 11.2 Situational Awareness, Fixation and External Pressure 11.3 Alcohol, Drugs and Crew Resource Management 11.4 Vision, Visual Limitations and Illusions 11.5 Stress and Stress Management 11.6 Threat and Error Management
12 Radio & AROC
12.1 Phonetic Alphabet, Phraseology and CTAF 12.2 The 121.5 MHz Emergency Frequency, Transponder Codes and the AROC
13 Risk & Operational Procedures
13.1 Job Safety Assessment, Risk Assessment and the Hierarchy of Controls 13.2 Site Survey, Bystander Management, Emergencies and Giving Way
14 Operations, Airworthiness & Reporting (RKOP)
14.1 Remote Pilot Responsibilities, Crew Briefing and Ground Operations 14.2 Operational, Remote Pilot and Technical Logs 14.3 Airworthiness, Serviceability and Defect Reporting 14.4 Role Equipment, Sensors and Payload Implications 14.5 Accident and Incident Reporting to the ATSB 14.6 Abnormal Operations, Fail-Safes and Flight Termination 14.7 Operating Near Aerodromes and Above 400 ft AGL
4.4 Weight and Balance: Terms and Limits
Key Takeaways Explain This Topic AI
Empty weight is the aircraft with no payload or usable energy source; operating weight adds crew-fixed items; maximum gross weight is the certificated ceiling that must never be exceeded.
A moment is an arm multiplied by a weight, and the centre of gravity is the total moment divided by the total weight.
The datum is the arbitrary reference point from which arms are measured, a station is a numbered location along the airframe, and an index unit is a scaling factor that keeps moment arithmetic manageable.
Exceeding maximum gross weight or flying outside the CG envelope reduces control authority, endurance and the ability to recover from a gust — and breaches the manufacturer's limits.
Last updated: August 2026
Why a Drone Pilot Needs Weight-and-Balance Vocabulary
Small multirotors rarely require a formal load sheet, which tempts candidates to skip this topic. That is a mistake for two reasons. First, Schedule 4 codes it priority A . Second, the moment you fit a heavier gimbal, add a second battery, or strap a spray tank to a 25 kg agricultural airframe, you are doing weight and balance whether you write it down or not — and RPA above 25 kg are individually listed on a RePL by name and maximum take-off weight precisely because their loading matters.
The Weight Terms
Term Definition
Empty weight The aircraft as built: airframe, motors, ESCs, flight controller, wiring. No payload, no battery in most manufacturers' definitions, no removable equipment.
Operating weight Empty weight plus the items always carried for the role — battery, gimbal mount, landing gear, propeller guards, ballast. The weight before mission payload is added.
Maximum gross weight (MTOW) The greatest weight at which the aircraft may legally and safely take off. Set by the manufacturer, and for RPA above 25 kg it is written onto the RePL.
Useful load Maximum gross weight minus operating weight — what is left for mission payload.
The arithmetic is simply: Useful load = Maximum gross weight − Operating weight \text{Useful load} = \text{Maximum gross weight} - \text{Operating weight} Useful load = Maximum gross weight − Operating weight
Worked example. A survey multirotor has an empty weight of 3.4 kg. Its operating fit is a 1.2 kg flight battery and a 0.4 kg gimbal mount, giving an operating weight of 5.0 kg . Its manufacturer-published MTOW is 7.0 kg. The useful load is 7.0 − 5.0 = 2.0 kg . A 2.3 kg LiDAR sensor therefore cannot be carried — not "can be carried carefully", but cannot be carried, because it puts the aircraft 300 g over MTOW before it leaves the ground.
Weight categories interact with this. That same airframe at 7.0 kg gross sits in the small category (more than 2 kg, not more than 25 kg). If a modification pushed it past 25 kg it would become a medium RPA, and the licensing, landholder and certification consequences change immediately.
The Balance Terms
Balance is about where the weight sits, not just how much there is.
Datum — an arbitrary reference point, specified by the manufacturer, from which all horizontal distances are measured. It may be the nose, the centre of the airframe, or a point in front of the aircraft. Its position is arbitrary; what matters is that everyone uses the same one.
Arm — the horizontal distance from the datum to the centre of gravity of an item. Arms behind the datum are positive, arms in front are negative (or the manufacturer places the datum ahead of everything so all arms are positive).
Moment — the turning effect of a weight about the datum: Moment = Weight × Arm \text{Moment} = \text{Weight} \times \text{Arm} Moment = Weight × Arm
Station — a numbered position along the airframe, expressed as its distance from the datum. "Station 45" means 45 units aft of the datum.
Index unit — a constant divisor applied to moments to keep the numbers small and readable on a load sheet. Dividing every moment by 100 or 1,000 does not change the balance result, only the size of the digits.
Centre of gravity (CG) — the point through which the total weight acts, found by dividing total moment by total weight.
Finding the Centre of Gravity CG = ∑ ( Weight × Arm ) ∑ Weight \text{CG} = \frac{\sum(\text{Weight} \times \text{Arm})}{\sum \text{Weight}} CG = ∑ Weight ∑ ( Weight × Arm )
Worked example. A hexacopter has a datum at the centre of the airframe, with forward arms negative and aft arms positive. Loading is:
- Item Weight (g) Arm (cm) Moment (g·cm)
- Airframe (operating) 4,000 0 0
- Flight battery 1,400 +6 +8,400
- Camera and gimbal 900 −14 −12,600
- Total 6,300 −4,200
CG = −4,200 ÷ 6,300 = −0.67 cm , or about 6.7 mm forward of the datum. If the manufacturer's envelope is ±15 mm, the aircraft is inside it. Move to a 1,300 g camera at the same arm and the moment becomes −18,200, giving a total of −9,800 and a CG of −1.46 cm — outside the envelope, even though total weight of 6,700 g is still below a 7,000 g MTOW. Weight and balance are two separate tests and an aircraft can pass one while failing the other.
Loading Limits and What Breaching Them Costs
Two limits define the safe envelope, and both must be respected:
The weight limit — never exceed maximum gross weight.
The CG limits — the forward and aft (and, on a multirotor, lateral) boundaries within which the CG must fall.
Exceeding maximum gross weight produces predictable consequences: a higher power requirement to hover, higher motor and ESC current, more heat, shorter endurance, a reduced climb rate, a longer stopping distance, and less spare thrust to recover from a gust. On a hot day at an elevated site those effects compound with density altitude, and the margin that would normally absorb a gust simply is not there.
Flying outside the CG envelope produces different symptoms. The flight controller is tuned for a specific CG, so an off-centre load forces one arm or one axis of motors to run continuously harder to hold the aircraft level. The results are:
Uneven control response — sluggish in one direction, twitchy in the other.
Reduced endurance, because the hard-working motors draw more current than the model predicts.
Premature motor and ESC wear, and higher temperatures on the loaded side.
In severe cases, loss of stable hover — the controller runs out of authority on the loaded axis and the aircraft drifts or oscillates.
Practical technique for a multirotor
Mount the battery in its designed position and orientation, and secure it — a pack that shifts in flight moves the CG in flight.
Balance-test the aircraft before the first flight with a new payload: support it under the manufacturer's CG point and confirm it sits level, or hover it a metre up and watch for a persistent tilt.
If you must fit an off-centre payload, add ballast on the opposite arm rather than accepting the imbalance, and recheck against MTOW after adding it.
Recheck after any modification — a heavier propeller set, larger landing gear, or an added parachute all change both weight and balance.