Study guide

7.1 Electrical Terms and RPAS Electrical Components

CASA Remote Pilot Licence RePL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the RePL Exam 1.2 How to Use This Guide & Build a Study Plan

2 RPA Air Law: Regulatory Framework & Standard Operating Conditions

2.1 CASR Part 101 and the Manual of Standards 2.2 Standard Operating Conditions (SOC) 2.3 The 120 m (400 ft) AGL Height Limit 2.4 VLOS, Daylight, Visibility and the One-RPA Rule

3 RPA Air Law: Licensing, Categories & Approvals

3.1 RePL vs ReOC: Pilot Licence vs Operator Certificate 3.2 Excluded Categories and Operator Accreditation 3.3 RPA Weight Categories and Registration 3.4 Operating Beyond the SOC: Approvals and the ReB1

4 Basic Aviation Knowledge (RBAK)

4.1 Direction, Wind Velocity and Aviation Time 4.2 Units of Measurement: Height, Altitude and Elevation 4.3 Aerodynamics: Lift, Drag, Thrust, Weight and Energy 4.4 Weight and Balance: Terms and Limits 4.5 Propellers and Rotors 4.6 Axes, Attitude and Flight Control Principles 4.7 The Remote Pilot Station

5 RPAS Systems: Platforms, C2 Link & Power

5.1 Multirotor vs Fixed-Wing Characteristics 5.2 Command-and-Control Link and Failsafes 5.3 Lithium-Polymer Battery Management and Safety

6 RPAS Systems: Sensors, Payload & Preflight

6.1 GNSS, Compass, IMU and Geofencing 6.2 Payload, Centre of Gravity and Pre-Flight Checks 6.3 Automated Flight Management Systems (RAFM)

7 Electrical & Electronic Systems (REES)

7.1 Electrical Terms and RPAS Electrical Components 7.2 Electric Motors, Kv and Current Draw 7.3 Battery Types, Specifications and Dangerous Goods 7.4 Charging, Discharging, Balancing and Battery Limitations 7.5 Radio Waves, Frequency Bands and Propagation 7.6 GPS Components, Errors and Electromagnetic Hazards

8 Multirotor Aerodynamics & Performance (RBKM)

8.1 Multirotor Airframe and Component Layout 8.2 Rotor Aerodynamics: Blade Design, Thrust, Drag and Torque 8.3 Hovering: Ground Effect, Recirculation and Translational Lift 8.4 Multirotor Flight Controls, Stabilisation and GPS Hold 8.5 Motor Failure, Rotor Direction and Abnormal Aerodynamics 8.6 Weight, Power, Wind and Climb Performance 8.7 Descent, Vortex Ring State and Landing

9 Navigation & Charts

9.1 Chart Fundamentals: Latitude, Longitude, Variation and Distance 9.2 Visual Terminal Charts and Visual Navigation Charts 9.3 Airspace Classes, Control Zones and CTA Steps 9.4 Restricted, Danger and Prohibited Areas and Obstacles 9.5 NOTAMs, the AIP and Chart Currency

10 Meteorology

10.1 Wind, Sea Breezes and Local Effects 10.2 Turbulence, Orographic Effects and Terrain 10.3 Thunderstorms, Fronts and Fog 10.4 Density Altitude, METAR/TAF and BoM Forecasts 10.5 Weather Observations: Reading the Sky and the Site

11 Human Factors

11.1 IMSAFE, Fatigue and Complacency 11.2 Situational Awareness, Fixation and External Pressure 11.3 Alcohol, Drugs and Crew Resource Management 11.4 Vision, Visual Limitations and Illusions 11.5 Stress and Stress Management 11.6 Threat and Error Management

12 Radio & AROC

12.1 Phonetic Alphabet, Phraseology and CTAF 12.2 The 121.5 MHz Emergency Frequency, Transponder Codes and the AROC

13 Risk & Operational Procedures

13.1 Job Safety Assessment, Risk Assessment and the Hierarchy of Controls 13.2 Site Survey, Bystander Management, Emergencies and Giving Way

14 Operations, Airworthiness & Reporting (RKOP)

14.1 Remote Pilot Responsibilities, Crew Briefing and Ground Operations 14.2 Operational, Remote Pilot and Technical Logs 14.3 Airworthiness, Serviceability and Defect Reporting 14.4 Role Equipment, Sensors and Payload Implications 14.5 Accident and Incident Reporting to the ATSB 14.6 Abnormal Operations, Fail-Safes and Flight Termination 14.7 Operating Near Aerodromes and Above 400 ft AGL

7.1 Electrical Terms and RPAS Electrical Components

Key Takeaways Explain This Topic AI

Volts measure electrical pressure, amps measure current, ohms measure resistance, watts measure power (volts x amps) and hertz measure frequency.

The core RPAS electrical chain is battery, then electronic speed controllers, then motors, with the flight controller, receiver, BEC and telemetry module drawing from the same supply.

Redundancy means duplicating a component so a single failure is survivable, and it is why hexacopters and octocopters exist while quadcopters have none.

Every electrical malfunction has a recognisable symptom and a defined remedial action; knowing the symptom-to-action mapping is what the exam tests.

Last updated: August 2026

Five Terms That Underpin the Whole Unit

REES — Electrical and electronic systems for RPAS — is the second-largest knowledge unit in the RePL syllabus with nine Schedule 4 topics, and it opens with vocabulary.

  • Term Symbol Measures Water analogy
  • Volt V Electrical potential difference — "pressure" Water pressure in the pipe
  • Ampere (amp) A Current — rate of charge flow Litres per second through the pipe
  • Ohm Ω Resistance — opposition to current Narrowness of the pipe
  • Watt W Power — rate of energy use Pressure × flow
  • Hertz Hz Frequency — cycles per second How fast something repeats

Two relationships tie them together and both appear in RPA work: V = I × R (Ohm’s law) V = I \times R \qquad\text{(Ohm's law)} V = I × R (Ohm’s law) P = V × I (Power) P = V \times I \qquad\text{(Power)} P = V × I (Power)

Worked example. A 6S LiPo at a nominal 22.2 V drives a multirotor drawing 40 A in the hover. Hover power is 22.2 × 40 = 888 W . If the same aircraft peaks at 90 A during an aggressive climb, peak power is 22.2 × 90 ≈ 2,000 W . That difference is why a battery's continuous and burst current ratings are separate numbers, and why a pack sized only for hover current sags badly under a climb.

Hertz turns up in three places on an RPAS: the radio frequency of the C2 link (2.4 GHz, 5.8 GHz, 900 MHz), the flight controller's loop rate, and the pulse-width-modulation frequency at which an ESC switches its output to the motor.

The Power Chain

Power flows in one direction through a recognisable chain:

Flight battery → power distribution board → electronic speed controllers (ESCs) → motors

with taps off that main bus feeding the flight controller, receiver, telemetry module, gimbal and payload.

The components Schedule 4 names

Electronic speed controller (ESC) — converts the battery's direct current into the timed three-phase output that spins a brushless motor, and sets its speed on command from the flight controller. One ESC per motor. ESCs run hot and are a common failure point.

Battery eliminator circuit (BEC) — a voltage regulator that steps the high pack voltage down to the 5 V or 12 V that the receiver, flight controller and servos need, "eliminating" the need for a separate receiver battery. A BEC failure kills the low-voltage electronics while the motors still have power — an ugly failure mode.

Receiver and remote receivers — decode the C2 uplink. "Remote receivers" are secondary receiver units mounted elsewhere on the airframe with their own antennas, giving diversity so the airframe cannot shadow the signal in every orientation at once.

Telemetry module — encodes and downlinks aircraft state.

Flight batteries — the main energy source (see the battery sections that follow).

Receiver battery — a separate small battery powering the receiver on airframes that do not use a BEC. Redundant power for the control electronics.

Circuit breakers and fuses — protective devices that open the circuit on an overcurrent, protecting wiring from a fire.

Servomechanisms (servos) — position-controlled actuators. Rare on a multirotor, essential on a fixed-wing for ailerons, elevator and rudder, and used everywhere for gimbals, release mechanisms and spray valves.

Aerials/antennas — radiating elements for the C2, telemetry, payload and GNSS links.

GPS receivers — decode satellite signals for position (see the GNSS section).

Altimeters — barometric for pressure height, and radio, radar, laser or acoustic altimeters for true height above the surface, used for terrain following and precision landing.

Collision avoidance sensors — vision, infrared, ultrasonic or lidar sensors that detect obstacles. Note the limits: most vision systems fail on featureless surfaces, in low light, and against thin objects such as wires.

Redundancy, Back-ups and Consequences of Failure

Redundancy means providing more of a component than the aircraft strictly needs, so that a single failure is survivable. Back-up means providing an alternative path or mode. Schedule 4 asks about both, and about the consequences of a malfunction and the remedial action .

Component Redundancy typically available Consequence of failure Remedial action

Motor Hexacopter: yes. Octocopter: yes, often two. Quadcopter: none Quad: loss of control, spin and descent. Hex/octo: degraded but controllable flight Land immediately at the nearest safe site; on a quad, aim the uncontrolled descent away from people

ESC Same as motor — one ESC per motor Same as motor failure; often preceded by a hot-ESC warning As above; retire the ESC and investigate before the next flight

Battery Dual-battery airframes (parallel packs) on larger platforms Sudden power loss and immediate uncontrolled descent Respect low-voltage warnings early; never fly a pack to empty

BEC Some airframes carry a dual/redundant BEC or a separate receiver battery Loss of flight controller and receiver power while motors still spin Not recoverable in flight — this is why the redundancy exists

Receiver Remote/diversity receivers Loss of the command uplink The pre-set failsafe executes (RTH, hover or land)

GNSS Multi-constellation receivers; some airframes carry dual GNSS units Loss of position hold and RTH; drift with the wind Switch to attitude mode and fly manually to a landing

IMU Most flight controllers run dual or triple redundant IMUs Attitude reference lost; violent oscillation or upset Voting between IMUs is automatic; a total loss is not recoverable

The pattern is worth internalising because it is how the questions are built: a symptom is described and you are asked for the consequence or the action. Two of them are worth memorising verbatim:

A quadcopter that loses one motor cannot maintain controlled flight. Three motors cannot simultaneously balance thrust and torque. The aircraft yaws and descends. The pilot's only meaningful input is where it comes down.

A hexacopter that loses one motor can usually continue level flight with reduced authority by redistributing thrust across the remaining five. It should still be landed at once.

Pre-flight and Symptom Recognition

Most electrical failures announce themselves before they become emergencies. Build these into the pre-flight and the post-flight:

Warm or hot motors, ESCs or battery after landing. Heat is wasted power. A single component consistently hotter than its neighbours points to a bearing, a mis-set ESC, a damaged winding, or an out-of-balance airframe forcing that arm to work harder.

Voltage sag under load. A pack that drops sharply when power is applied and recovers slowly is either under-specified for the aircraft's current draw or near the end of its cycle life.

Intermittent link or telemetry. Check antenna connectors and routing before blaming the environment; a coaxial connector loosened by vibration is a very common cause.

Corroded, chafed or discoloured wiring and connectors. Discolouration around a connector means it has been running hot — a high-resistance joint, which by Ohm's law dissipates power as heat exactly where you least want it.

Blown fuse or tripped breaker. Never reset and fly. A protective device operates because something drew more current than it should; find the cause first.

Record every one of these in the technical log . A "warm motor 3" note that appears three flights in a row is a maintenance finding, not a coincidence.