Study guide

7.6 GPS Components, Errors and Electromagnetic Hazards

CASA Remote Pilot Licence RePL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the RePL Exam 1.2 How to Use This Guide & Build a Study Plan

2 RPA Air Law: Regulatory Framework & Standard Operating Conditions

2.1 CASR Part 101 and the Manual of Standards 2.2 Standard Operating Conditions (SOC) 2.3 The 120 m (400 ft) AGL Height Limit 2.4 VLOS, Daylight, Visibility and the One-RPA Rule

3 RPA Air Law: Licensing, Categories & Approvals

3.1 RePL vs ReOC: Pilot Licence vs Operator Certificate 3.2 Excluded Categories and Operator Accreditation 3.3 RPA Weight Categories and Registration 3.4 Operating Beyond the SOC: Approvals and the ReB1

4 Basic Aviation Knowledge (RBAK)

4.1 Direction, Wind Velocity and Aviation Time 4.2 Units of Measurement: Height, Altitude and Elevation 4.3 Aerodynamics: Lift, Drag, Thrust, Weight and Energy 4.4 Weight and Balance: Terms and Limits 4.5 Propellers and Rotors 4.6 Axes, Attitude and Flight Control Principles 4.7 The Remote Pilot Station

5 RPAS Systems: Platforms, C2 Link & Power

5.1 Multirotor vs Fixed-Wing Characteristics 5.2 Command-and-Control Link and Failsafes 5.3 Lithium-Polymer Battery Management and Safety

6 RPAS Systems: Sensors, Payload & Preflight

6.1 GNSS, Compass, IMU and Geofencing 6.2 Payload, Centre of Gravity and Pre-Flight Checks 6.3 Automated Flight Management Systems (RAFM)

7 Electrical & Electronic Systems (REES)

7.1 Electrical Terms and RPAS Electrical Components 7.2 Electric Motors, Kv and Current Draw 7.3 Battery Types, Specifications and Dangerous Goods 7.4 Charging, Discharging, Balancing and Battery Limitations 7.5 Radio Waves, Frequency Bands and Propagation 7.6 GPS Components, Errors and Electromagnetic Hazards

8 Multirotor Aerodynamics & Performance (RBKM)

8.1 Multirotor Airframe and Component Layout 8.2 Rotor Aerodynamics: Blade Design, Thrust, Drag and Torque 8.3 Hovering: Ground Effect, Recirculation and Translational Lift 8.4 Multirotor Flight Controls, Stabilisation and GPS Hold 8.5 Motor Failure, Rotor Direction and Abnormal Aerodynamics 8.6 Weight, Power, Wind and Climb Performance 8.7 Descent, Vortex Ring State and Landing

9 Navigation & Charts

9.1 Chart Fundamentals: Latitude, Longitude, Variation and Distance 9.2 Visual Terminal Charts and Visual Navigation Charts 9.3 Airspace Classes, Control Zones and CTA Steps 9.4 Restricted, Danger and Prohibited Areas and Obstacles 9.5 NOTAMs, the AIP and Chart Currency

10 Meteorology

10.1 Wind, Sea Breezes and Local Effects 10.2 Turbulence, Orographic Effects and Terrain 10.3 Thunderstorms, Fronts and Fog 10.4 Density Altitude, METAR/TAF and BoM Forecasts 10.5 Weather Observations: Reading the Sky and the Site

11 Human Factors

11.1 IMSAFE, Fatigue and Complacency 11.2 Situational Awareness, Fixation and External Pressure 11.3 Alcohol, Drugs and Crew Resource Management 11.4 Vision, Visual Limitations and Illusions 11.5 Stress and Stress Management 11.6 Threat and Error Management

12 Radio & AROC

12.1 Phonetic Alphabet, Phraseology and CTAF 12.2 The 121.5 MHz Emergency Frequency, Transponder Codes and the AROC

13 Risk & Operational Procedures

13.1 Job Safety Assessment, Risk Assessment and the Hierarchy of Controls 13.2 Site Survey, Bystander Management, Emergencies and Giving Way

14 Operations, Airworthiness & Reporting (RKOP)

14.1 Remote Pilot Responsibilities, Crew Briefing and Ground Operations 14.2 Operational, Remote Pilot and Technical Logs 14.3 Airworthiness, Serviceability and Defect Reporting 14.4 Role Equipment, Sensors and Payload Implications 14.5 Accident and Incident Reporting to the ATSB 14.6 Abnormal Operations, Fail-Safes and Flight Termination 14.7 Operating Near Aerodromes and Above 400 ft AGL

7.6 GPS Components, Errors and Electromagnetic Hazards

Key Takeaways Explain This Topic AI

A GNSS fix needs at least four satellites for a three-dimensional position; more satellites and better geometry give a lower dilution of precision and a more accurate fix.

GNSS accuracy is degraded by poor satellite geometry, multipath reflections off buildings and water, ionospheric effects, and antenna obstruction.

Powerlines, LTE and Wi-Fi are the three electromagnetic hazards Schedule 4 names, and all three can disturb the C2 link, the compass or the GNSS receiver.

The compass is the sensor most vulnerable to local magnetic interference, and a corrupted heading is the classic cause of a return-to-home flyaway.

Last updated: August 2026

The Three Segments of a GNSS

GPS is the United States constellation; GNSS (Global Navigation Satellite System) is the generic term covering GPS, the Russian GLONASS , the European Galileo and the Chinese BeiDou . Modern RPA receivers are multi-constellation, which is why satellite counts on a ground station often exceed twenty.

Schedule 4 topic 8(a) asks for the components of a GPS , and the standard answer is three segments:

Segment What it is

Space segment The satellite constellation itself, each satellite broadcasting its position and a precise time signal

Control segment Ground monitoring and uplink stations that track the satellites and correct their orbital and clock data

User segment The receiver in the aircraft — antenna, processor and clock — that decodes the signals and computes a position

How a fix is computed

Each satellite transmits its identity, its orbital position and the exact time of transmission. The receiver measures how long the signal took to arrive and multiplies by the speed of light to get a range to that satellite. One range puts the receiver on a sphere; two ranges intersect in a circle; three narrow it to two points, one of which is absurd. In practice a fourth satellite is needed to solve for the receiver's own clock error, so:

Three satellites → a 2D fix (latitude and longitude, no reliable altitude).

Four or more satellites → a 3D fix including altitude.

Six or seven or more , well distributed, → a robust fix suitable for automated flight.

Accuracy and DOP

Dilution of precision (DOP) expresses how good the satellite geometry is, independent of how many satellites there are. Satellites spread widely across the sky produce well-crossing range spheres and a low DOP; satellites clustered in one part of the sky produce shallow intersections and a high DOP. HDOP is the horizontal component and is the figure most ground stations display.

  • HDOP Quality
  • Below 1.0 Excellent
  • 1.0 – 1.5 Good — suitable for automated flight
  • 1.5 – 2.0 Moderate — acceptable with caution
  • Above 2.0 Poor — position error may be large

Standard GNSS gives horizontal accuracy of a few metres. RTK (real-time kinematic) and PPK (post-processed kinematic) systems use a base station or correction service to reach centimetre accuracy, and are standard on survey and mapping aircraft.

Factors That Degrade GNSS Accuracy

Schedule 4 topic 8(c) lists them, and the practical versions are:

Number of satellites available. Fewer satellites means a weaker solution. Deep valleys, urban canyons and dense canopy all cut the visible count.

Path interference and multipath. Signals reflecting off buildings, cliffs, water or vehicles arrive slightly late, and the receiver may compute the range from the reflection rather than the direct path. Multipath is worst near tall buildings and over still water.

Type of software / receiver processing. Multi-constellation, multi-frequency receivers with good filtering resolve a better fix than a basic single-frequency unit.

Signal availability. Ionospheric disturbance, deliberate jamming, and any physical obstruction of the antenna reduce it. Never place a payload, a hand or a metal bracket over the GNSS antenna.

Indications of faulty equipment. Erratic satellite count, a fix that will not settle, a home point recorded metres from the actual launch position, position wander in a hover with no wind, or an altitude reading that drifts while the aircraft is stationary.

GNSS-Denied and Degraded Operations

If the fix is lost in flight the flight controller cannot hold position. Typical behaviour:

The aircraft drifts with the wind rather than holding station.

Many systems fall back to attitude (ATTI) mode , holding a level attitude and altitude but leaving position to the pilot.

Return-to-home becomes unavailable or unreliable , because RTH navigates to a stored GNSS home point.

The pilot's job is to know their aircraft's GNSS-loss behaviour before they need it, to keep the aircraft within visual line of sight so manual recovery is possible, and to be current on manual attitude-mode flying. An operator whose pilots have never flown in ATTI mode has an unpractised emergency procedure.

Electromagnetic Hazards: EMI, Powerlines, LTE and Wi-Fi

Schedule 4 topic 9 names three hazards specifically.

Electromagnetic interference (EMI) is any unwanted electromagnetic energy that disturbs a system. On an RPA it comes from outside — transmitters, industrial equipment, powerlines — and from inside, where the ESCs and motor leads radiate noise into the compass and GNSS antenna a few centimetres away.

Powerlines. High-voltage transmission lines and substations are a triple hazard:

A physical strike hazard. Conductors are thin, low-contrast against terrain and sky, and effectively invisible from the aircraft's camera. Powerline strikes are among the most common RPA accidents.

A magnetic hazard. The current flowing in a conductor produces a magnetic field that can deflect the aircraft's compass , corrupting heading.

A radio hazard. High-voltage lines produce corona discharge and broadband electrical noise that raises the noise floor for the C2 link.

The mitigation is separation. Keep meaningful lateral distance from conductors, and if an inspection task requires close work, plan for compass disturbance and reduced link margin rather than being surprised by them.

LTE and Wi-Fi. Mobile networks and Wi-Fi share or sit adjacent to the 2.4 GHz and 5 GHz bands used by most consumer and commercial RPAS links. In a dense urban environment the 2.4 GHz band can be almost fully occupied. Symptoms are video stuttering, rising latency, intermittent telemetry and a falling link-quality reading. Mitigations: select a less-congested channel or band where the equipment allows it, use a directional ground antenna, get physical height and clear line of sight, and move the operating position away from access points and cell sites.

The Compass: The Most Interference-Prone Sensor

The magnetometer senses the earth's magnetic field to determine heading, and the earth's field is weak — which makes local ferrous and electromagnetic sources disproportionately influential.

Common sources at a typical work site: reinforced concrete with steel rebar, a vehicle roof or bonnet used as a launch pad, buried services and pipelines, steel structures and shipping containers, powerlines, and the aircraft's own motors and power leads.

Why it matters more than it looks: the flight controller uses heading to compute both position-hold corrections and the RTH bearing . A compass reading 40 degrees in error sends the aircraft 40 degrees off course on return — the classic flyaway .

Defences:

Calibrate after changing airframe components or battery type, after travelling a significant distance from the last calibration site, and whenever the ground station reports a compass error.

Never launch from a metal surface , a vehicle, a manhole cover or a rebar-reinforced pad. Use a portable landing pad on open ground.

Run the on-site interference check the ground station offers, and treat a high interference value as a reason to move the launch point rather than a nuisance warning to dismiss.

Watch the first hover. A steady drift with no wind and no stick input is a compass or IMU problem. Land and investigate rather than pressing on.