Study guide
7.5 Radio Waves, Frequency Bands and Propagation
CASA Remote Pilot Licence RePL
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the RePL Exam 1.2 How to Use This Guide & Build a Study Plan
2 RPA Air Law: Regulatory Framework & Standard Operating Conditions
2.1 CASR Part 101 and the Manual of Standards 2.2 Standard Operating Conditions (SOC) 2.3 The 120 m (400 ft) AGL Height Limit 2.4 VLOS, Daylight, Visibility and the One-RPA Rule
3 RPA Air Law: Licensing, Categories & Approvals
3.1 RePL vs ReOC: Pilot Licence vs Operator Certificate 3.2 Excluded Categories and Operator Accreditation 3.3 RPA Weight Categories and Registration 3.4 Operating Beyond the SOC: Approvals and the ReB1
4 Basic Aviation Knowledge (RBAK)
4.1 Direction, Wind Velocity and Aviation Time 4.2 Units of Measurement: Height, Altitude and Elevation 4.3 Aerodynamics: Lift, Drag, Thrust, Weight and Energy 4.4 Weight and Balance: Terms and Limits 4.5 Propellers and Rotors 4.6 Axes, Attitude and Flight Control Principles 4.7 The Remote Pilot Station
5 RPAS Systems: Platforms, C2 Link & Power
5.1 Multirotor vs Fixed-Wing Characteristics 5.2 Command-and-Control Link and Failsafes 5.3 Lithium-Polymer Battery Management and Safety
6 RPAS Systems: Sensors, Payload & Preflight
6.1 GNSS, Compass, IMU and Geofencing 6.2 Payload, Centre of Gravity and Pre-Flight Checks 6.3 Automated Flight Management Systems (RAFM)
7 Electrical & Electronic Systems (REES)
7.1 Electrical Terms and RPAS Electrical Components 7.2 Electric Motors, Kv and Current Draw 7.3 Battery Types, Specifications and Dangerous Goods 7.4 Charging, Discharging, Balancing and Battery Limitations 7.5 Radio Waves, Frequency Bands and Propagation 7.6 GPS Components, Errors and Electromagnetic Hazards
8 Multirotor Aerodynamics & Performance (RBKM)
8.1 Multirotor Airframe and Component Layout 8.2 Rotor Aerodynamics: Blade Design, Thrust, Drag and Torque 8.3 Hovering: Ground Effect, Recirculation and Translational Lift 8.4 Multirotor Flight Controls, Stabilisation and GPS Hold 8.5 Motor Failure, Rotor Direction and Abnormal Aerodynamics 8.6 Weight, Power, Wind and Climb Performance 8.7 Descent, Vortex Ring State and Landing
9 Navigation & Charts
9.1 Chart Fundamentals: Latitude, Longitude, Variation and Distance 9.2 Visual Terminal Charts and Visual Navigation Charts 9.3 Airspace Classes, Control Zones and CTA Steps 9.4 Restricted, Danger and Prohibited Areas and Obstacles 9.5 NOTAMs, the AIP and Chart Currency
10 Meteorology
10.1 Wind, Sea Breezes and Local Effects 10.2 Turbulence, Orographic Effects and Terrain 10.3 Thunderstorms, Fronts and Fog 10.4 Density Altitude, METAR/TAF and BoM Forecasts 10.5 Weather Observations: Reading the Sky and the Site
11 Human Factors
11.1 IMSAFE, Fatigue and Complacency 11.2 Situational Awareness, Fixation and External Pressure 11.3 Alcohol, Drugs and Crew Resource Management 11.4 Vision, Visual Limitations and Illusions 11.5 Stress and Stress Management 11.6 Threat and Error Management
12 Radio & AROC
12.1 Phonetic Alphabet, Phraseology and CTAF 12.2 The 121.5 MHz Emergency Frequency, Transponder Codes and the AROC
13 Risk & Operational Procedures
13.1 Job Safety Assessment, Risk Assessment and the Hierarchy of Controls 13.2 Site Survey, Bystander Management, Emergencies and Giving Way
14 Operations, Airworthiness & Reporting (RKOP)
14.1 Remote Pilot Responsibilities, Crew Briefing and Ground Operations 14.2 Operational, Remote Pilot and Technical Logs 14.3 Airworthiness, Serviceability and Defect Reporting 14.4 Role Equipment, Sensors and Payload Implications 14.5 Accident and Incident Reporting to the ATSB 14.6 Abnormal Operations, Fail-Safes and Flight Termination 14.7 Operating Near Aerodromes and Above 400 ft AGL
7.5 Radio Waves, Frequency Bands and Propagation
Key Takeaways Explain This Topic AI
The aviation-relevant bands run MF, HF, VHF and UHF; VHF and UHF are line-of-sight while HF can refract off the ionosphere for long-range work.
Lower frequencies penetrate obstacles better but carry less data; higher frequencies carry more data but are blocked more easily.
Terrain, buildings, ionospheric conditions, sunspot activity, electrical equipment and thunderstorms all affect propagation.
A pre-flight range test confirms the C2 link at the intended geometry, and is the only reliable way to know your effective range at a given site.
Last updated: August 2026
Radio Waves and Their Characteristics
A radio wave is electromagnetic energy travelling at the speed of light. Three properties describe it:
Frequency — cycles per second, in hertz. Aviation and RPAS frequencies run from hundreds of kilohertz to several gigahertz.
Wavelength — the physical distance of one cycle, inversely proportional to frequency: λ = c f \lambda = \frac{c}{f} λ = f c where c is the speed of light. A 121.5 MHz signal has a wavelength of about 2.5 m; a 5.8 GHz signal about 5 cm. This is why an aviation VHF antenna is long and a 5.8 GHz drone antenna is a stub.
Polarisation — the orientation of the wave's electric field, set by the antenna's orientation. Mismatched polarisation between transmitter and receiver loses a large fraction of the available signal.
The Band Ranges
- Band Frequency range Propagation Aviation and RPAS use
- MF — medium frequency 300 kHz – 3 MHz Ground wave by day, sky wave at night Non-directional beacons (NDB)
HF — high frequency 3 – 30 MHz Sky wave: refracts off the ionosphere for very long range Oceanic and remote-area long-range communications
VHF — very high frequency 30 – 300 MHz Line of sight Aviation voice radio (118.000–136.975 MHz), 121.5 MHz emergency
UHF — ultra high frequency 300 MHz – 3 GHz Line of sight, shorter range, higher data capacity GNSS (~1.2–1.6 GHz), transponders, 433/900 MHz telemetry links
SHF — super high frequency 3 – 30 GHz Strict line of sight 5.8 GHz video and C2 links, weather radar
RPAS command-and-control and video links live mostly in the ISM (industrial, scientific and medical) bands — 2.4 GHz and 5.8 GHz — with 900 MHz and 433 MHz used for long-range telemetry. These are unlicensed shared bands: convenient and cheap, but you share them with Wi-Fi, cordless equipment and every other drone at the site.
The frequency trade-off
There is a consistent trade running through the whole table:
Lower frequency → longer wavelength → better penetration of foliage, buildings and terrain, longer range for a given power, but less data capacity and a physically larger antenna.
Higher frequency → shorter wavelength → more data capacity (high-definition video), smaller antenna, but more easily blocked by obstacles and shorter effective range.
This is why a long-range telemetry link runs at 900 MHz while the HD video runs at 5.8 GHz on the same aircraft: each frequency is chosen for what it must carry.
Line of Sight and Effective Range
VHF and above are line-of-sight propagation: the signal travels in a straight line and does not follow the curvature of the earth or bend around a hill. For an RPA this has two consequences.
First, effective range is a geometry problem, not a product specification. A manufacturer's "8 km range" figure is measured in open terrain with clear line of sight and no interference. Put a ridge, a tree line or a steel-framed building between the ground station and the aircraft and the usable range collapses — sometimes to a few hundred metres.
Second, height helps . Raising the ground antenna, or flying the aircraft higher, extends the radio horizon. A pilot standing in a gully with the aircraft behind a rise has no path at all; the same pilot moving 50 m onto the ridge line may have a solid link.
Factors Affecting Propagation
Schedule 4 topic 7(b)(iii) lists five factors explicitly. Each has a practical RPAS consequence.
Terrain. Hills, ridges and cuttings physically block line-of-sight paths. Terrain also reflects signals, producing multipath — the receiver gets the direct signal plus a delayed reflection, and the two can partially cancel. Multipath is why a link can be poor at one position and solid five metres away.
The ionosphere. Layers of ionised gas 60–600 km up refract HF signals back to earth, allowing long-range HF communication far beyond line of sight. The ionosphere varies with time of day (more layers by day, fewer at night), season, and solar activity. It does not usefully refract VHF and above, which pass straight through — which is exactly why GNSS works and why VHF is line-of-sight.
Sunspot activity. The 11-year solar cycle changes ionospheric ionisation. High solar activity improves long-range HF propagation but also produces solar flares and geomagnetic storms that degrade GNSS accuracy and can cause brief outages. Space-weather warnings are worth checking before a precision-survey flight.
Interference from electrical equipment. High-voltage powerlines, substations, welding equipment, industrial motors and switch-mode power supplies all radiate broadband electrical noise that raises the receiver's noise floor and cuts effective range.
Thunderstorms. Lightning produces enormous broadband radio noise, heard as crackling on an HF or AM receiver. A storm within tens of kilometres can degrade radio links — and long before that becomes the limiting factor, the storm itself is a reason not to be flying.
Digital Versus Analogue
Schedule 4 topic 7(c) asks about digital and analogue signals and about shielding and optimisation .
Analogue signals degrade gracefully. Analogue video gets progressively noisier as signal weakens — snow, then rolling bars, then nothing — giving the pilot warning.
Digital signals degrade abruptly. A digital link is clean right up to the point where error correction can no longer keep up, and then it drops out entirely — the "digital cliff". A pilot watching perfect HD video has very little warning before the picture and the link disappear.
That difference matters operationally: on a digital system, watch the link-quality indicator, not the picture . The RSSI or signal-bar reading is the early warning that a clean picture will not give you.
Shielding reduces radiated interference between components on the airframe: braided or foil shields on power leads, ferrite chokes, physical separation between the ESCs and the GNSS/compass module, and grounding of the shield at one end only. It is why the GNSS antenna on most commercial multirotors sits on a mast or on top of the shell, as far from the power electronics as the airframe allows.
Range Testing
The only reliable way to know your effective range at a given site is a range test , and Schedule 4 names it (topic 7(c)(ii), command and control link range testing ).
A practical procedure:
Power up the aircraft and the ground station and let the link establish.
With the aircraft on the ground and not armed , walk away from it while watching the link-quality reading, or use the manufacturer's dedicated range-test mode.
Note the distance at which link quality begins to degrade. Ground-level testing is pessimistic — the link will usually be better in the air — but it establishes a relative baseline.
Repeat with the antennas in the orientation you will actually use.
In flight, fly a short, close orbit before transiting downrange, and confirm link quality stays solid through all headings — this detects airframe shadowing, where the aircraft's own body blocks the antenna at certain angles.
Do the test at the site , not once in the car park at home. Range is a property of the environment, not of the aircraft.