Study guide

8.7 Descent, Vortex Ring State and Landing

CASA Remote Pilot Licence RePL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the RePL Exam 1.2 How to Use This Guide & Build a Study Plan

2 RPA Air Law: Regulatory Framework & Standard Operating Conditions

2.1 CASR Part 101 and the Manual of Standards 2.2 Standard Operating Conditions (SOC) 2.3 The 120 m (400 ft) AGL Height Limit 2.4 VLOS, Daylight, Visibility and the One-RPA Rule

3 RPA Air Law: Licensing, Categories & Approvals

3.1 RePL vs ReOC: Pilot Licence vs Operator Certificate 3.2 Excluded Categories and Operator Accreditation 3.3 RPA Weight Categories and Registration 3.4 Operating Beyond the SOC: Approvals and the ReB1

4 Basic Aviation Knowledge (RBAK)

4.1 Direction, Wind Velocity and Aviation Time 4.2 Units of Measurement: Height, Altitude and Elevation 4.3 Aerodynamics: Lift, Drag, Thrust, Weight and Energy 4.4 Weight and Balance: Terms and Limits 4.5 Propellers and Rotors 4.6 Axes, Attitude and Flight Control Principles 4.7 The Remote Pilot Station

5 RPAS Systems: Platforms, C2 Link & Power

5.1 Multirotor vs Fixed-Wing Characteristics 5.2 Command-and-Control Link and Failsafes 5.3 Lithium-Polymer Battery Management and Safety

6 RPAS Systems: Sensors, Payload & Preflight

6.1 GNSS, Compass, IMU and Geofencing 6.2 Payload, Centre of Gravity and Pre-Flight Checks 6.3 Automated Flight Management Systems (RAFM)

7 Electrical & Electronic Systems (REES)

7.1 Electrical Terms and RPAS Electrical Components 7.2 Electric Motors, Kv and Current Draw 7.3 Battery Types, Specifications and Dangerous Goods 7.4 Charging, Discharging, Balancing and Battery Limitations 7.5 Radio Waves, Frequency Bands and Propagation 7.6 GPS Components, Errors and Electromagnetic Hazards

8 Multirotor Aerodynamics & Performance (RBKM)

8.1 Multirotor Airframe and Component Layout 8.2 Rotor Aerodynamics: Blade Design, Thrust, Drag and Torque 8.3 Hovering: Ground Effect, Recirculation and Translational Lift 8.4 Multirotor Flight Controls, Stabilisation and GPS Hold 8.5 Motor Failure, Rotor Direction and Abnormal Aerodynamics 8.6 Weight, Power, Wind and Climb Performance 8.7 Descent, Vortex Ring State and Landing

9 Navigation & Charts

9.1 Chart Fundamentals: Latitude, Longitude, Variation and Distance 9.2 Visual Terminal Charts and Visual Navigation Charts 9.3 Airspace Classes, Control Zones and CTA Steps 9.4 Restricted, Danger and Prohibited Areas and Obstacles 9.5 NOTAMs, the AIP and Chart Currency

10 Meteorology

10.1 Wind, Sea Breezes and Local Effects 10.2 Turbulence, Orographic Effects and Terrain 10.3 Thunderstorms, Fronts and Fog 10.4 Density Altitude, METAR/TAF and BoM Forecasts 10.5 Weather Observations: Reading the Sky and the Site

11 Human Factors

11.1 IMSAFE, Fatigue and Complacency 11.2 Situational Awareness, Fixation and External Pressure 11.3 Alcohol, Drugs and Crew Resource Management 11.4 Vision, Visual Limitations and Illusions 11.5 Stress and Stress Management 11.6 Threat and Error Management

12 Radio & AROC

12.1 Phonetic Alphabet, Phraseology and CTAF 12.2 The 121.5 MHz Emergency Frequency, Transponder Codes and the AROC

13 Risk & Operational Procedures

13.1 Job Safety Assessment, Risk Assessment and the Hierarchy of Controls 13.2 Site Survey, Bystander Management, Emergencies and Giving Way

14 Operations, Airworthiness & Reporting (RKOP)

14.1 Remote Pilot Responsibilities, Crew Briefing and Ground Operations 14.2 Operational, Remote Pilot and Technical Logs 14.3 Airworthiness, Serviceability and Defect Reporting 14.4 Role Equipment, Sensors and Payload Implications 14.5 Accident and Incident Reporting to the ATSB 14.6 Abnormal Operations, Fail-Safes and Flight Termination 14.7 Operating Near Aerodromes and Above 400 ft AGL

8.7 Descent, Vortex Ring State and Landing

Key Takeaways Explain This Topic AI

Vortex ring state occurs when a rotorcraft descends vertically into its own downwash, so the rotor recirculates air already moving downward and loses lift.

The three conditions that produce it are a high vertical descent rate, little or no horizontal airspeed, and power applied.

Adding power makes vortex ring state worse; the recovery is to move horizontally out of the disturbed air column.

Landing into wind, descending at a moderate rate, and descending along a slanted path rather than vertically all prevent it.

Last updated: August 2026

The Condition Schedule 4 Names by Name

Vortex ring state (VRS) — also called settling with power — is the one multirotor aerodynamic hazard the Part 101 MOS singles out for both avoidance and recovery. It is priority A , and it is examined.

What happens

In normal flight the rotor draws air from above and accelerates it downward, and that column of downwash falls away behind the aircraft. In a vertical descent , the aircraft moves down into the very column it has just created. The rotor now ingests air that is already moving downward .

Two things follow. First, the induced flow through the disc rises sharply, which reduces the effective angle of attack at each blade section and cuts thrust — the same mechanism as recirculation, but self-generated. Second, the airflow around the disc organises itself into a doughnut-shaped vortex ring : air flows down through the centre of the disc, out at the edges, up around the outside, and back over the top into the centre. The rotor is now churning its own wake in a closed loop and is producing very little useful thrust at all.

The three conditions

VRS requires all three of these simultaneously:

A high rate of vertical descent — the aircraft is descending into its own downwash faster than the downwash is escaping.

Little or no horizontal airspeed — a descending aircraft moving forward flies out of its own wake continuously and cannot establish the ring.

Power applied — the rotors must be actively producing downwash for there to be a wake to descend into. An unpowered descent cannot enter VRS.

Remove any one condition and VRS cannot form. That is the whole of both the avoidance technique and the recovery.

What the pilot sees

An increasing rate of descent that does not respond to power.

Buffeting and vibration as the disc works in turbulent, unsteady flow.

Loss of control effectiveness — roll and pitch inputs feel mushy because the disc is not producing clean thrust.

On telemetry, high current draw with a continuing descent — the motors are working hard and achieving nothing.

Why Adding Power Makes It Worse

This is the central counter-intuitive point, and it is the one the exam tests.

The instinctive response to an unwanted descent is to add power. In VRS, adding power increases the downwash the rotor is producing — which strengthens the very column the aircraft is descending into, intensifies the vortex ring, and increases the descent rate. Pilots describe the aircraft as "falling faster the harder you pull".

The same logic explains why VRS is most dangerous close to the ground: the pilot pulls power, the aircraft accelerates downward, and there is no altitude left in which to try anything else. Most multirotor VRS accidents are landing accidents.

Recovery: Go Sideways, Not Up

The recovery is to break condition 2 — establish horizontal airspeed so the rotors fly into clean, undisturbed air.

Apply forward (or lateral) cyclic — move horizontally. Any direction will do; forward is usually easiest to judge. The aim is to fly the aircraft out of the descending column of air it created.

Do not add power while still in the ring. Power added before horizontal flight is established makes the condition worse. Once the aircraft is clearly translating and the descent has arrested, restore power normally.

Accept altitude loss. Recovery costs height. If VRS is entered close to the ground there may not be enough height to recover, which is why avoidance matters far more than recovery technique.

Once clear, re-establish a normal descent profile — slower, and with a forward component.

Avoidance: The Descent Profile That Cannot Enter VRS

Prevention is entirely a matter of descent technique:

Descend along a slanted path , not vertically. A descent with a forward component continuously moves the rotors into fresh air, and the wake is left behind.

Keep the descent rate moderate. Manufacturers commonly advise limiting vertical descent rates to a few metres per second; check your aircraft's flight manual for its figure.

Land into wind. The headwind gives the aircraft airspeed even when its groundspeed is zero, so the rotors are always meeting undisturbed air. This is the single most effective habit.

Never descend vertically at speed over a landing point. The common bad habit — climb to height, transit, then drop straight down onto the pad — is exactly the VRS recipe.

Be alert on the lee side of obstacles , where descending air from a rotor or downdraft adds to the aircraft's own descent.

Landing into wind: the other advantages

Schedule 4 topic 10(c) asks specifically for the advantages of landing or recovering into wind , and there are four:

Translational lift is retained. With a headwind the rotors meet moving air even at zero groundspeed, so the rotor is more efficient and less likely to enter VRS.

Lower groundspeed on arrival. The wind provides part of the deceleration, so the touchdown is gentler and the aircraft is easier to place accurately.

Better directional control. A headwind gives a fixed-wing weathercock stability and gives a multirotor a consistent, predictable tilt to hold rather than a shifting one.

A shorter and steeper approach path over the ground , which matters when there are obstacles on the approach.

Pre-Landing Checks

Schedule 4 topic 10(d) asks for pre-landing checks. A workable set:

  • Check Why
  • Landing area still clear People, animals and vehicles move. The area that was clear at take-off may not be now

Surface condition Firm, level, free of loose debris the downwash will lift into the rotors or into bystanders' eyes

  • Wind at the surface Direction and strength for the into-wind approach; check for gustiness
  • Battery reserve Enough for the approach, a possible go-around and a second attempt
  • Obstacles on the approach path Wires, branches, guy ropes and fences that were not on the departure path
  • Descent rate set Moderate, with a forward component; not a vertical drop
  • Crew and bystanders briefed Everyone clear of the landing area and aware the aircraft is returning
  • Payload and gear Retractable gear extended and locked; gimbal stowed or protected

Finish the approach with the aircraft in sight and the pilot's attention on it. The last two metres are where most landing damage occurs, precisely because the flight feels finished before it is.