Study guide
9.3 Airspace Classes, Control Zones and CTA Steps
CASA Remote Pilot Licence RePL
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the RePL Exam 1.2 How to Use This Guide & Build a Study Plan
2 RPA Air Law: Regulatory Framework & Standard Operating Conditions
2.1 CASR Part 101 and the Manual of Standards 2.2 Standard Operating Conditions (SOC) 2.3 The 120 m (400 ft) AGL Height Limit 2.4 VLOS, Daylight, Visibility and the One-RPA Rule
3 RPA Air Law: Licensing, Categories & Approvals
3.1 RePL vs ReOC: Pilot Licence vs Operator Certificate 3.2 Excluded Categories and Operator Accreditation 3.3 RPA Weight Categories and Registration 3.4 Operating Beyond the SOC: Approvals and the ReB1
4 Basic Aviation Knowledge (RBAK)
4.1 Direction, Wind Velocity and Aviation Time 4.2 Units of Measurement: Height, Altitude and Elevation 4.3 Aerodynamics: Lift, Drag, Thrust, Weight and Energy 4.4 Weight and Balance: Terms and Limits 4.5 Propellers and Rotors 4.6 Axes, Attitude and Flight Control Principles 4.7 The Remote Pilot Station
5 RPAS Systems: Platforms, C2 Link & Power
5.1 Multirotor vs Fixed-Wing Characteristics 5.2 Command-and-Control Link and Failsafes 5.3 Lithium-Polymer Battery Management and Safety
6 RPAS Systems: Sensors, Payload & Preflight
6.1 GNSS, Compass, IMU and Geofencing 6.2 Payload, Centre of Gravity and Pre-Flight Checks 6.3 Automated Flight Management Systems (RAFM)
7 Electrical & Electronic Systems (REES)
7.1 Electrical Terms and RPAS Electrical Components 7.2 Electric Motors, Kv and Current Draw 7.3 Battery Types, Specifications and Dangerous Goods 7.4 Charging, Discharging, Balancing and Battery Limitations 7.5 Radio Waves, Frequency Bands and Propagation 7.6 GPS Components, Errors and Electromagnetic Hazards
8 Multirotor Aerodynamics & Performance (RBKM)
8.1 Multirotor Airframe and Component Layout 8.2 Rotor Aerodynamics: Blade Design, Thrust, Drag and Torque 8.3 Hovering: Ground Effect, Recirculation and Translational Lift 8.4 Multirotor Flight Controls, Stabilisation and GPS Hold 8.5 Motor Failure, Rotor Direction and Abnormal Aerodynamics 8.6 Weight, Power, Wind and Climb Performance 8.7 Descent, Vortex Ring State and Landing
9 Navigation & Charts
9.1 Chart Fundamentals: Latitude, Longitude, Variation and Distance 9.2 Visual Terminal Charts and Visual Navigation Charts 9.3 Airspace Classes, Control Zones and CTA Steps 9.4 Restricted, Danger and Prohibited Areas and Obstacles 9.5 NOTAMs, the AIP and Chart Currency
10 Meteorology
10.1 Wind, Sea Breezes and Local Effects 10.2 Turbulence, Orographic Effects and Terrain 10.3 Thunderstorms, Fronts and Fog 10.4 Density Altitude, METAR/TAF and BoM Forecasts 10.5 Weather Observations: Reading the Sky and the Site
11 Human Factors
11.1 IMSAFE, Fatigue and Complacency 11.2 Situational Awareness, Fixation and External Pressure 11.3 Alcohol, Drugs and Crew Resource Management 11.4 Vision, Visual Limitations and Illusions 11.5 Stress and Stress Management 11.6 Threat and Error Management
12 Radio & AROC
12.1 Phonetic Alphabet, Phraseology and CTAF 12.2 The 121.5 MHz Emergency Frequency, Transponder Codes and the AROC
13 Risk & Operational Procedures
13.1 Job Safety Assessment, Risk Assessment and the Hierarchy of Controls 13.2 Site Survey, Bystander Management, Emergencies and Giving Way
14 Operations, Airworthiness & Reporting (RKOP)
14.1 Remote Pilot Responsibilities, Crew Briefing and Ground Operations 14.2 Operational, Remote Pilot and Technical Logs 14.3 Airworthiness, Serviceability and Defect Reporting 14.4 Role Equipment, Sensors and Payload Implications 14.5 Accident and Incident Reporting to the ATSB 14.6 Abnormal Operations, Fail-Safes and Flight Termination 14.7 Operating Near Aerodromes and Above 400 ft AGL
9.3 Airspace Classes, Control Zones and CTA Steps
Key Takeaways Explain This Topic AI
Class G is uncontrolled, non-towered airspace where most standard RPA operations occur; no ATC clearance is required to operate in Class G.
Class C and Class D are controlled airspace; an RPA generally cannot enter them — or the surface-level Control Zone (CTR) around a towered aerodrome — without ATC clearance and, for a non-standard operation, ReOC approval.
A Control Zone (CTR) is controlled airspace from the surface up to its boundary around a towered aerodrome; inside a CTR the CTA step altitudes are irrelevant because controlled airspace already reaches the ground.
CTA steps are the stepped bases of controlled airspace at increasing distances and altitudes from a towered aerodrome; each step is published in feet AMSL and must be converted to AGL using charted terrain elevation.
Standard RPA operations must not be flown within 5.5 km (3 NM) of a controlled aerodrome without approval; this distance rule interacts with the CTR boundary to protect towered traffic.
Last updated: August 2026
Airspace Classes Relevant to RPA
Australia uses the ICAO airspace classification system. For a Remote Pilot Licence (RePL) holder operating under the standard operating conditions, three classes matter day to day:
Class G — uncontrolled, non-towered. The default airspace outside controlled zones and upper airspace. Most standard RPA operations occur in Class G. No Air Traffic Control (ATC) clearance is required, though you must still observe the standard operating conditions, keep clear of manned aircraft, and use CTAF procedures at non-towered aerodromes.
Class D — controlled, typically around regional towered aerodromes. Entry requires ATC clearance . An RPA generally cannot enter Class D without that clearance and, for operations outside the standard conditions, a Remote Operator Certificate (ReOC) approval.
Class C — controlled, typically around major capital-city and high-density terminal areas. Entry likewise requires ATC clearance and, outside standard conditions, ReOC approval.
Rule of thumb: if the airspace is Class C or Class D, treat it as closed to a standard RPA operation unless you have explicitly obtained clearance and any required approval.
Controlled vs Uncontrolled Airspace
- Airspace Controlled? Tower present? RPA entry without clearance
- Class G No No Permitted (standard conditions)
- Class D Yes Yes (regional) Not permitted
- Class C Yes Yes (major) Not permitted
- Control Zone (CTR)
A Control Zone (CTR) is the surface-to-boundary controlled airspace around a towered aerodrome . It is usually Class D or Class C. The defining feature is that controlled airspace reaches from the ground up to the CTR upper limit. Inside a CTR:
The CTA step altitudes printed on the chart are not the controlling factor — the controlled airspace already starts at the surface.
An RPA cannot operate inside the CTR without ATC clearance (and, outside standard conditions, ReOC approval).
The CTR boundary is the first thing to check when planning a flight near a towered aerodrome.
CTR Dimensions and the Surface-to-Boundary Concept
CTR shape and size vary by aerodrome. A typical regional Class D CTR is a circle or polygon of roughly 5 to 8 NM radius centred on the aerodrome reference point, extending from the surface (SFC) up to a published upper limit such as 2,500 ft or 4,500 ft AMSL. Capital-city Class C CTRs are larger and more complex, often with several sectors and stepped upper limits. The charted boundary is what matters: any point inside the boundary, at any altitude from the ground up to the upper limit, is inside controlled airspace. "Surface-to-boundary" means there is no low-level gap below the CTR — the controlled airspace touches the ground throughout the zone.
CTA Steps
Control Area (CTA) steps are the stepped bases of controlled airspace that sit above and around a CTR. As you move outward from a towered aerodrome, the base of controlled airspace rises in defined steps — for example, 1,000 ft AMSL close in, 2,000 ft AMSL further out, 3,000 ft AMSL beyond that. Each step is published on the VTC or VNC in feet AMSL and applies from the step line outward until the next step line.
Reading a CTA Step Table
The chart margin often prints a CTA step table summarising the stepped bases around each major aerodrome. A typical entry looks like:
- Distance from aerodrome CTA base
- Within CTR Surface
- 0–5 NM 1,000 ft AMSL
- 5–10 NM 2,000 ft AMSL
- 10–20 NM 3,000 ft AMSL
Read the table together with the chart: find your operating distance from the aerodrome reference point, read across to the CTA base, then convert that base to AGL using the charted terrain elevation at your site. A step base of 1,000 ft AMSL over 600 ft terrain gives a 400 ft AGL base — tight for a 400 ft AGL RPA, and likely inside controlled airspace if the RPA reaches the full 120 m.
Example: Transit Near a Class D Aerodrome
You plan a survey 8 NM from a regional Class D towered aerodrome, outside the CTR. The CTA step table shows a 2,000 ft AMSL base at that distance; terrain is 800 ft AMSL. The AGL base is 1,200 ft, well above your 400 ft AGL operating height, so the standard flight sits below the CTA step. You are also beyond the 5.5 km (3 NM) controlled-aerodrome buffer. The flight is legal under the standard conditions, provided you remain in Class G, stay clear of the CTR, and monitor the CTAF for any nearby non-towered traffic.
To know whether an RPA flight sits below a given step:
Read the charted step base (AMSL).
Read the charted ground elevation at the operating point (AMSL).
Subtract to get the step base in AGL: step base (AMSL) − terrain (AMSL) = step base (AGL) .
Compare the step base (AGL) against your planned RPA height (AGL).
If the operating point is inside the CTR , this calculation is irrelevant — controlled airspace already covers the surface. Always resolve the CTR question first, then the CTA-step question.
The 5.5 km (3 NM) Controlled-Aerodrome Rule
CASA's standard operating conditions prohibit an RPA from being operated within 5.5 km (3 NM) of a controlled aerodrome without approval. A controlled aerodrome is one inside a CTR. This distance rule is a buffer that protects arriving and departing manned traffic and works alongside the CTR boundary:
The CTR boundary itself may be smaller or larger than 5.5 km depending on the aerodrome.
Even if a point is outside the charted CTR, if it is within 5.5 km of the aerodrome reference point, the standard conditions still bar the flight unless approval is obtained.
Approval pathways typically require a ReOC holder to apply and ATC to coordinate.
Entering Controlled Airspace vs the 5.5 km Rule
These two rules are often confused but govern different things:
Entering controlled airspace (CTR or CTA) is about altitude and location — whether your RPA, at its operating height over that point, is inside Class C or Class D airspace. It requires ATC clearance (and ReOC approval outside standard conditions).
The 5.5 km / 3 NM rule is about proximity to a controlled aerodrome — a horizontal distance buffer that applies even when the RPA is below the CTA base and outside the CTR. It protects traffic patterns and circuit areas.
A flight can be below the CTA base and outside the CTR and still be barred by the 5.5 km rule. Conversely, a flight can be more than 5.5 km from the aerodrome and still be inside controlled airspace if it climbs into a CTA step. Both checks are independent and both must pass.
Putting It Together — Pre-flight Airspace Check
Plot the operating area on the current VTC or VNC and mark the operating altitude.
Check whether the point sits inside a CTR (surface controlled). If yes, the flight is a controlled-airspace operation requiring clearance.
If outside the CTR, check the 5.5 km / 3 NM buffer to any controlled aerodrome reference point.
If clear of the CTR and the buffer, check the CTA step base above the point using the step table or charted step lines, convert to AGL, and confirm the planned RPA height stays below it.
Confirm the airspace class (G is the target for standard operations).
Record each result as part of your pre-flight planning so the reasoning is auditable.