Study guide

9.2 Visual Terminal Charts and Visual Navigation Charts

CASA Remote Pilot Licence RePL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the RePL Exam 1.2 How to Use This Guide & Build a Study Plan

2 RPA Air Law: Regulatory Framework & Standard Operating Conditions

2.1 CASR Part 101 and the Manual of Standards 2.2 Standard Operating Conditions (SOC) 2.3 The 120 m (400 ft) AGL Height Limit 2.4 VLOS, Daylight, Visibility and the One-RPA Rule

3 RPA Air Law: Licensing, Categories & Approvals

3.1 RePL vs ReOC: Pilot Licence vs Operator Certificate 3.2 Excluded Categories and Operator Accreditation 3.3 RPA Weight Categories and Registration 3.4 Operating Beyond the SOC: Approvals and the ReB1

4 Basic Aviation Knowledge (RBAK)

4.1 Direction, Wind Velocity and Aviation Time 4.2 Units of Measurement: Height, Altitude and Elevation 4.3 Aerodynamics: Lift, Drag, Thrust, Weight and Energy 4.4 Weight and Balance: Terms and Limits 4.5 Propellers and Rotors 4.6 Axes, Attitude and Flight Control Principles 4.7 The Remote Pilot Station

5 RPAS Systems: Platforms, C2 Link & Power

5.1 Multirotor vs Fixed-Wing Characteristics 5.2 Command-and-Control Link and Failsafes 5.3 Lithium-Polymer Battery Management and Safety

6 RPAS Systems: Sensors, Payload & Preflight

6.1 GNSS, Compass, IMU and Geofencing 6.2 Payload, Centre of Gravity and Pre-Flight Checks 6.3 Automated Flight Management Systems (RAFM)

7 Electrical & Electronic Systems (REES)

7.1 Electrical Terms and RPAS Electrical Components 7.2 Electric Motors, Kv and Current Draw 7.3 Battery Types, Specifications and Dangerous Goods 7.4 Charging, Discharging, Balancing and Battery Limitations 7.5 Radio Waves, Frequency Bands and Propagation 7.6 GPS Components, Errors and Electromagnetic Hazards

8 Multirotor Aerodynamics & Performance (RBKM)

8.1 Multirotor Airframe and Component Layout 8.2 Rotor Aerodynamics: Blade Design, Thrust, Drag and Torque 8.3 Hovering: Ground Effect, Recirculation and Translational Lift 8.4 Multirotor Flight Controls, Stabilisation and GPS Hold 8.5 Motor Failure, Rotor Direction and Abnormal Aerodynamics 8.6 Weight, Power, Wind and Climb Performance 8.7 Descent, Vortex Ring State and Landing

9 Navigation & Charts

9.1 Chart Fundamentals: Latitude, Longitude, Variation and Distance 9.2 Visual Terminal Charts and Visual Navigation Charts 9.3 Airspace Classes, Control Zones and CTA Steps 9.4 Restricted, Danger and Prohibited Areas and Obstacles 9.5 NOTAMs, the AIP and Chart Currency

10 Meteorology

10.1 Wind, Sea Breezes and Local Effects 10.2 Turbulence, Orographic Effects and Terrain 10.3 Thunderstorms, Fronts and Fog 10.4 Density Altitude, METAR/TAF and BoM Forecasts 10.5 Weather Observations: Reading the Sky and the Site

11 Human Factors

11.1 IMSAFE, Fatigue and Complacency 11.2 Situational Awareness, Fixation and External Pressure 11.3 Alcohol, Drugs and Crew Resource Management 11.4 Vision, Visual Limitations and Illusions 11.5 Stress and Stress Management 11.6 Threat and Error Management

12 Radio & AROC

12.1 Phonetic Alphabet, Phraseology and CTAF 12.2 The 121.5 MHz Emergency Frequency, Transponder Codes and the AROC

13 Risk & Operational Procedures

13.1 Job Safety Assessment, Risk Assessment and the Hierarchy of Controls 13.2 Site Survey, Bystander Management, Emergencies and Giving Way

14 Operations, Airworthiness & Reporting (RKOP)

14.1 Remote Pilot Responsibilities, Crew Briefing and Ground Operations 14.2 Operational, Remote Pilot and Technical Logs 14.3 Airworthiness, Serviceability and Defect Reporting 14.4 Role Equipment, Sensors and Payload Implications 14.5 Accident and Incident Reporting to the ATSB 14.6 Abnormal Operations, Fail-Safes and Flight Termination 14.7 Operating Near Aerodromes and Above 400 ft AGL

9.2 Visual Terminal Charts and Visual Navigation Charts

Key Takeaways Explain This Topic AI

VTCs (Visual Terminal Charts) cover the vicinity of major aerodromes and terminal areas at roughly 1:250,000 scale; VNCs (Visual Navigation Charts) cover the broader areas between VTCs at 1:500,000.

Charted heights and airspace bases are AMSL (above mean sea level); RPA operating height limits are AGL (above ground level), so convert using the charted ground elevation before deciding if a flight is below a CTA base.

Both VTC and VNC depict airspace classes, CTA steps, CTAF, restricted/danger/prohibited areas, obstacles (towers, masts, powerlines) and elevations, and hazards.

Always confirm you are using the current chart edition; edition dates are printed on each chart and superseded editions must not be used for flight planning.

A CTA base shown as 1,200 ft AMSL over 600 ft AMSL terrain gives an AGL base of 600 ft; a 120 m (400 ft) AGL RPA flight sits at roughly 1,000 ft AMSL and is below that base, but the CTR (Control Zone) surface layer still needs checking.

Last updated: August 2026

Visual Terminal Charts and Visual Navigation Charts

For a CASA Remote Pilot Licence (RePL) holder operating under the standard operating conditions, visual navigation is the primary means of deciding where you can and cannot fly. Two chart series do most of the work: the Visual Terminal Chart (VTC) and the Visual Navigation Chart (VNC) . Both are published by Airservices Australia and are the official pictorial representation of airspace, terrain, and hazards for visual flight rules (VFR) pilots. As an RPA pilot you operate almost entirely under VFR, so these two charts — together with the NOTAM system covered in Section 6.4 — are the foundation of legal route planning.

VTC — Visual Terminal Chart

A VTC covers the vicinity of major aerodromes and their terminal areas . It is the chart you reach for whenever an operation sits near a capital-city aerodrome or a busy regional towered field. Key characteristics:

Scale: approximately 1:250,000 — the most detailed of the two visual series. At this scale, 1 cm on the chart represents about 2.5 km on the ground, which is fine enough to resolve individual control-zone steps, CTAF rings, and clusters of obstacles near a field.

Coverage: a defined terminal area around one or more major aerodromes (for example, the Sydney, Melbourne, Brisbane, Perth, Adelaide, and Gold Coast terminal areas, plus major regional towers).

Depicts: airspace classes and boundaries, Control Zones (CTR), Control Area (CTA) steps, Common Traffic Advisory Frequency (CTAF) areas, restricted/danger/prohibited areas, obstacles (towers, masts, powerlines) with elevations, significant terrain, and hazards.

Use case: planning operations within or near a terminal area where precise airspace boundaries and obstacle densities matter.

VNC — Visual Navigation Chart

A VNC covers the broader areas between VTCs . When an operation is outside a terminal area, the VNC is the appropriate chart.

Scale: 1:500,000 — less terminal-area detail but wider coverage. At this scale, 1 cm represents about 5 km, sufficient for regional route planning but coarse enough that you should switch to the VTC when approaching a terminal area.

Coverage: regional and remote areas not served by a VTC.

Depicts: the same family of information as the VTC (airspace classes, CTA steps, CTAF, restricted/danger/prohibited areas, obstacles, terrain) at a coarser resolution.

Use case: cross-country or regional RPA operations away from major aerodromes.

  • Feature VTC VNC
  • Approximate scale 1:250,000 (1 cm ≈ 2.5 km) 1:500,000 (1 cm ≈ 5 km)
  • Coverage Terminal area vicinity Areas between VTCs
  • Detail level Higher Moderate
  • Typical use Near major aerodromes Regional/remote ops
  • Reading Elevations: AMSL versus AGL

The single most important habit on any visual chart is distinguishing AMSL (above mean sea level, sometimes labelled ALT) from AGL (above ground level). Charted airspace bases, obstacle heights, and terrain elevations are published in AMSL . RPA standard operating height limits, however, are expressed in AGL — the CASA standard limit is 120 m (approximately 400 ft) AGL unless otherwise approved. Mixing the two is one of the most common planning errors and can put an RPA inside controlled airspace without the pilot realising it.

To compare an RPA height limit with a charted airspace base you must first convert one to the other using the charted ground elevation: Airspace base (AMSL) − Ground elevation (AMSL) = Airspace base (AGL)

Ground elevation is read from the chart's contour and spot-height layer. VTCs and VNCs show relief using a combination of contour lines (lines of constant elevation, drawn at fixed intervals), spot heights (individual point elevations marked with a dot and a figure), and layer tinting or hypsometric shading that gives higher ground a distinct colour. Where the operating site sits on a slope, read the nearest contour or spot height that bounds the site — do not interpolate across a wide valley. Where terrain varies across the operating area, use the highest ground elevation under the planned flight to give the most conservative (lowest) AGL airspace base.

Worked Example

Suppose the chart shows a CTA base of 1,200 ft AMSL over terrain charted at 600 ft AMSL .

Subtract the ground elevation from the airspace base: 1,200 − 600 = 600 ft AGL . That is the controlled airspace base above the ground at that point.

Your RPA flight at the standard 120 m (≈400 ft) AGL sits at roughly 1,000 ft AMSL (600 ft terrain + 400 ft AGL).

1,000 ft AMSL is below the 1,200 ft AMSL CTA base, so the flight is below the CTA step at that location.

This does not by itself clear the flight — you must also check whether the point sits inside a Control Zone (CTR) , which is controlled airspace from the surface up to its boundary. Inside a CTR, the CTA base is irrelevant because the controlled airspace already reaches the ground.

If the same CTA base sat over 900 ft AMSL terrain instead, the AGL base would be only 300 ft — below your 400 ft AGL operating height — and the standard flight would enter controlled airspace. Same charted step, different terrain, opposite result. That is why the conversion must be done at the operating point, not read off the step label alone.

Symbols You Must Recognise

Airspace class boundaries: solid and dashed lines with the class letter (G, D, C) annotated along the boundary.

CTA steps: stepped lines with the base altitude in feet AMSL printed along each segment; each step's base applies from that line outward until the next step.

CTR (Control Zone): a boundary enclosing a towered aerodrome, surface to its upper limit.

CTAF: a dashed circle around a non-towered aerodrome with the frequency printed in a small frequency box; the number is the frequency you broadcast on to coordinate with other traffic, not an ATC clearance frequency.

Restricted, danger, and prohibited areas: hatched or dotted areas with an identifier (e.g., RA3, D, P) and activation details; the identifier tells you the tier, the activation note tells you when it applies.

Obstacles: towers, masts, and powerlines marked with a symbol and an elevation in feet AMSL; group obstacles may carry a grouped elevation. Lit obstacles carry a dedicated light symbol.

Aerodromes: towered fields show a controlled-aerodrome symbol with the tower frequency; non-towered fields show a CTAF symbol and frequency.

The CTAF Frequency Box

Around each non-towered aerodrome the chart prints a CTAF frequency box — the Common Traffic Advisory Frequency on which pilots self-broadcast position and intentions. For an RPA pilot operating near a non-towered field, this box tells you two things: the frequency to monitor (and, where your aircraft is equipped, to broadcast on), and the lateral extent of the CTAF area within which you should be making calls. Broadcasting on CTAF is not an ATC clearance — it is collision-avoidance coordination with other traffic.

Chart Edition and Currency

Every VTC and VNC prints an edition date in the chart margin. Airservices publishes new editions on a regular cycle, and between editions changes are promulgated by NOTAM and the AIP. Before planning, check the edition date against the current edition published by Airservices; a superseded chart may show CTA steps, restricted areas, or obstacles that have since changed. Using the current edition is part of the pre-flight workflow described in Section 6.4 — it is not optional.

Key habit: every height on a VTC or VNC is AMSL unless explicitly marked AGL. Convert at the operating point using the highest charted ground elevation under the flight, and confirm the chart edition is current before you plan.