Study guide
5.3 Lithium-Polymer Battery Management and Safety
CASA Remote Pilot Licence RePL
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the RePL Exam 1.2 How to Use This Guide & Build a Study Plan
2 RPA Air Law: Regulatory Framework & Standard Operating Conditions
2.1 CASR Part 101 and the Manual of Standards 2.2 Standard Operating Conditions (SOC) 2.3 The 120 m (400 ft) AGL Height Limit 2.4 VLOS, Daylight, Visibility and the One-RPA Rule
3 RPA Air Law: Licensing, Categories & Approvals
3.1 RePL vs ReOC: Pilot Licence vs Operator Certificate 3.2 Excluded Categories and Operator Accreditation 3.3 RPA Weight Categories and Registration 3.4 Operating Beyond the SOC: Approvals and the ReB1
4 Basic Aviation Knowledge (RBAK)
4.1 Direction, Wind Velocity and Aviation Time 4.2 Units of Measurement: Height, Altitude and Elevation 4.3 Aerodynamics: Lift, Drag, Thrust, Weight and Energy 4.4 Weight and Balance: Terms and Limits 4.5 Propellers and Rotors 4.6 Axes, Attitude and Flight Control Principles 4.7 The Remote Pilot Station
5 RPAS Systems: Platforms, C2 Link & Power
5.1 Multirotor vs Fixed-Wing Characteristics 5.2 Command-and-Control Link and Failsafes 5.3 Lithium-Polymer Battery Management and Safety
6 RPAS Systems: Sensors, Payload & Preflight
6.1 GNSS, Compass, IMU and Geofencing 6.2 Payload, Centre of Gravity and Pre-Flight Checks 6.3 Automated Flight Management Systems (RAFM)
7 Electrical & Electronic Systems (REES)
7.1 Electrical Terms and RPAS Electrical Components 7.2 Electric Motors, Kv and Current Draw 7.3 Battery Types, Specifications and Dangerous Goods 7.4 Charging, Discharging, Balancing and Battery Limitations 7.5 Radio Waves, Frequency Bands and Propagation 7.6 GPS Components, Errors and Electromagnetic Hazards
8 Multirotor Aerodynamics & Performance (RBKM)
8.1 Multirotor Airframe and Component Layout 8.2 Rotor Aerodynamics: Blade Design, Thrust, Drag and Torque 8.3 Hovering: Ground Effect, Recirculation and Translational Lift 8.4 Multirotor Flight Controls, Stabilisation and GPS Hold 8.5 Motor Failure, Rotor Direction and Abnormal Aerodynamics 8.6 Weight, Power, Wind and Climb Performance 8.7 Descent, Vortex Ring State and Landing
9 Navigation & Charts
9.1 Chart Fundamentals: Latitude, Longitude, Variation and Distance 9.2 Visual Terminal Charts and Visual Navigation Charts 9.3 Airspace Classes, Control Zones and CTA Steps 9.4 Restricted, Danger and Prohibited Areas and Obstacles 9.5 NOTAMs, the AIP and Chart Currency
10 Meteorology
10.1 Wind, Sea Breezes and Local Effects 10.2 Turbulence, Orographic Effects and Terrain 10.3 Thunderstorms, Fronts and Fog 10.4 Density Altitude, METAR/TAF and BoM Forecasts 10.5 Weather Observations: Reading the Sky and the Site
11 Human Factors
11.1 IMSAFE, Fatigue and Complacency 11.2 Situational Awareness, Fixation and External Pressure 11.3 Alcohol, Drugs and Crew Resource Management 11.4 Vision, Visual Limitations and Illusions 11.5 Stress and Stress Management 11.6 Threat and Error Management
12 Radio & AROC
12.1 Phonetic Alphabet, Phraseology and CTAF 12.2 The 121.5 MHz Emergency Frequency, Transponder Codes and the AROC
13 Risk & Operational Procedures
13.1 Job Safety Assessment, Risk Assessment and the Hierarchy of Controls 13.2 Site Survey, Bystander Management, Emergencies and Giving Way
14 Operations, Airworthiness & Reporting (RKOP)
14.1 Remote Pilot Responsibilities, Crew Briefing and Ground Operations 14.2 Operational, Remote Pilot and Technical Logs 14.3 Airworthiness, Serviceability and Defect Reporting 14.4 Role Equipment, Sensors and Payload Implications 14.5 Accident and Incident Reporting to the ATSB 14.6 Abnormal Operations, Fail-Safes and Flight Termination 14.7 Operating Near Aerodromes and Above 400 ft AGL
5.3 Lithium-Polymer Battery Management and Safety
Key Takeaways Explain This Topic AI
A LiPo cell is 3.7 V nominal, 4.2 V fully charged, about 3.8 V storage, and permanently damaged below about 3.0-3.3 V - never over-discharge.
Multi-cell packs must be balance charged via the balance lead so no cell is over- or under-charged relative to the pack.
A swollen or puffy LiPo is a fire precursor - retire it immediately; never charge, fly, or reuse a puffed pack.
Charge in a fire-safe location (LiPo bag, non-flammable surface), never unattended, at the correct C rate (1C standard).
C-rating gives the max discharge current (capacity in Ah multiplied by C); plan to land with 20-30% capacity remaining and always check per-cell voltage before flight.
Last updated: August 2026
Lithium-Polymer (LiPo) Battery Fundamentals
The LiPo (Lithium-Polymer) battery is the dominant power source for small and medium RPAS because of its high energy density and high discharge rate. It is also the most safety-critical component on the aircraft: mishandled LiPos can swell, catch fire, or explode. Understanding cell voltage and care is non-negotiable for a Remote Pilot Licence holder.
Cell Voltage and States
A LiPo cell has a nominal voltage of 3.7 V . The safe operating range and key states are:
- State Voltage per cell Notes
- Fully charged 4.2 V Maximum safe voltage; do not exceed
- Nominal 3.7 V Mid-range, in-use voltage
- Storage voltage ~3.8 V Long-term storage level; safe for weeks or months
- Low warning ~3.5-3.6 V Time to land soon
- Damage floor ~3.0-3.3 V Below this, cells are permanently damaged
- Resting after flight ~3.7-3.8 V Healthy post-flight level if not over-discharged
Never over-discharge a LiPo below roughly 3.0-3.3 V per cell - the cell chemistry is damaged, capacity drops permanently, and the cell becomes unsafe. Most flight controllers have a low-voltage warning; respect it and land promptly.
Balance Charging
A multi-cell LiPo (for example 3S = 3 cells, 4S = 4 cells, 6S = 6 cells) must be balance charged using the balance lead. Balance charging monitors and equalises the voltage of each cell individually so that no cell is over-charged (which causes swelling or fire) or under-charged relative to the pack. Always use a balance charger and the balance lead - never fast-charge a multi-cell pack without balancing.
Storage Practice
If a LiPo will not be used for more than a few days, it should be brought to storage voltage (~3.8 V/cell) using the charger's storage mode. Storing a LiPo:
Fully charged for long periods risks swelling, internal damage, and fire.
Fully discharged risks dropping below the damage floor through self-discharge.
Store packs in a fire-safe location (LiPo bag, metal ammo box, or ceramic container) at room temperature, away from flammable materials.
Swelling and Puffy Cells - Retire Immediately
A swollen or puffy LiPo cell is a cell whose internal chemistry has begun to gas. This is irreversible and is a fire precursor. Retire a swollen pack immediately - do not attempt to recharge, discharge, or use it just once more. Discharge it safely (for example via a resistor or salt-water bath per local guidance) and dispose of it at a battery recycling point.
Fire-Safe Charging
Charge in a fire-safe location : a LiPo fire bag, on a non-flammable surface, away from combustibles.
Never charge unattended - most LiPo fires occur during charging.
Use the correct charger and charge rate (1C is standard: a 2200 mAh pack charged at 2.2 A). Higher rates are possible only if the pack label permits.
Charge in a place where, if a fire starts, it cannot spread - not on a carpeted floor near furniture.
C-Rating and Maximum Current
The C-rating states the maximum continuous discharge current. For a 5000 mAh pack rated 20C:
Max current = capacity (Ah) x C-rating = 5.0 Ah x 20 = 100 A .
Choose a pack whose C-rating comfortably exceeds the aircraft's peak current draw; too low a C-rating causes voltage sag, overheating, and premature failure under load. Burst ratings (for example 20C/30C burst) apply for only a few seconds.
Capacity (mAh) and Endurance Estimation
Capacity in mAh (milliamp-hours) sets how long the aircraft can fly. A rough endurance estimate:
Flight time (min) is approximately (Capacity mAh x 0.8 divided by average hover draw in mAh/min).
The 0.8 factor reserves about 20% - never fly a pack to empty. For example, a 5000 mAh pack with an average draw of 1000 mAh/min gives roughly (5000 x 0.8 / 1000) = 4.0 min to the reserve point - adjust for real draw measured in flight. Always plan to land with at least 20-30% capacity remaining.
Pre-Flight Voltage Check
Before every flight, check the per-cell voltage with a cell checker or the charger. A healthy fully-charged pack reads about 4.2 V/cell; a storage-charged pack (~3.8 V) should be topped up before flight. If any cell reads significantly lower than the others (more than about 0.05-0.1 V), the pack is unbalanced or damaged - do not fly it.
Series and Parallel Packs, and Voltage Sag
A pack's total voltage is the sum of its cells in series (a 4S pack reads about 16.8 V fully charged). Parallel packs add capacity at the same voltage. Under load, a healthy pack sags only a few tenths of a volt; a pack that sags sharply and recovers slowly is either under-spec for the aircraft's current draw or nearing the end of its cycle life. Persistent voltage sag, warmth after flight, or a cell that will not balance are all signs to ground the pack and investigate before the next flight.
Transport
Transport LiPos in a fire-proof bag with terminals insulated (never loose in a bag where contacts can short). Keep them away from metal objects and out of direct sun. For air transport, follow airline and CASA dangerous-goods rules - carry-on limits and terminal taping usually apply.