Study guide
6.2 Payload, Centre of Gravity and Pre-Flight Checks
CASA Remote Pilot Licence RePL
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the RePL Exam 1.2 How to Use This Guide & Build a Study Plan
2 RPA Air Law: Regulatory Framework & Standard Operating Conditions
2.1 CASR Part 101 and the Manual of Standards 2.2 Standard Operating Conditions (SOC) 2.3 The 120 m (400 ft) AGL Height Limit 2.4 VLOS, Daylight, Visibility and the One-RPA Rule
3 RPA Air Law: Licensing, Categories & Approvals
3.1 RePL vs ReOC: Pilot Licence vs Operator Certificate 3.2 Excluded Categories and Operator Accreditation 3.3 RPA Weight Categories and Registration 3.4 Operating Beyond the SOC: Approvals and the ReB1
4 Basic Aviation Knowledge (RBAK)
4.1 Direction, Wind Velocity and Aviation Time 4.2 Units of Measurement: Height, Altitude and Elevation 4.3 Aerodynamics: Lift, Drag, Thrust, Weight and Energy 4.4 Weight and Balance: Terms and Limits 4.5 Propellers and Rotors 4.6 Axes, Attitude and Flight Control Principles 4.7 The Remote Pilot Station
5 RPAS Systems: Platforms, C2 Link & Power
5.1 Multirotor vs Fixed-Wing Characteristics 5.2 Command-and-Control Link and Failsafes 5.3 Lithium-Polymer Battery Management and Safety
6 RPAS Systems: Sensors, Payload & Preflight
6.1 GNSS, Compass, IMU and Geofencing 6.2 Payload, Centre of Gravity and Pre-Flight Checks 6.3 Automated Flight Management Systems (RAFM)
7 Electrical & Electronic Systems (REES)
7.1 Electrical Terms and RPAS Electrical Components 7.2 Electric Motors, Kv and Current Draw 7.3 Battery Types, Specifications and Dangerous Goods 7.4 Charging, Discharging, Balancing and Battery Limitations 7.5 Radio Waves, Frequency Bands and Propagation 7.6 GPS Components, Errors and Electromagnetic Hazards
8 Multirotor Aerodynamics & Performance (RBKM)
8.1 Multirotor Airframe and Component Layout 8.2 Rotor Aerodynamics: Blade Design, Thrust, Drag and Torque 8.3 Hovering: Ground Effect, Recirculation and Translational Lift 8.4 Multirotor Flight Controls, Stabilisation and GPS Hold 8.5 Motor Failure, Rotor Direction and Abnormal Aerodynamics 8.6 Weight, Power, Wind and Climb Performance 8.7 Descent, Vortex Ring State and Landing
9 Navigation & Charts
9.1 Chart Fundamentals: Latitude, Longitude, Variation and Distance 9.2 Visual Terminal Charts and Visual Navigation Charts 9.3 Airspace Classes, Control Zones and CTA Steps 9.4 Restricted, Danger and Prohibited Areas and Obstacles 9.5 NOTAMs, the AIP and Chart Currency
10 Meteorology
10.1 Wind, Sea Breezes and Local Effects 10.2 Turbulence, Orographic Effects and Terrain 10.3 Thunderstorms, Fronts and Fog 10.4 Density Altitude, METAR/TAF and BoM Forecasts 10.5 Weather Observations: Reading the Sky and the Site
11 Human Factors
11.1 IMSAFE, Fatigue and Complacency 11.2 Situational Awareness, Fixation and External Pressure 11.3 Alcohol, Drugs and Crew Resource Management 11.4 Vision, Visual Limitations and Illusions 11.5 Stress and Stress Management 11.6 Threat and Error Management
12 Radio & AROC
12.1 Phonetic Alphabet, Phraseology and CTAF 12.2 The 121.5 MHz Emergency Frequency, Transponder Codes and the AROC
13 Risk & Operational Procedures
13.1 Job Safety Assessment, Risk Assessment and the Hierarchy of Controls 13.2 Site Survey, Bystander Management, Emergencies and Giving Way
14 Operations, Airworthiness & Reporting (RKOP)
14.1 Remote Pilot Responsibilities, Crew Briefing and Ground Operations 14.2 Operational, Remote Pilot and Technical Logs 14.3 Airworthiness, Serviceability and Defect Reporting 14.4 Role Equipment, Sensors and Payload Implications 14.5 Accident and Incident Reporting to the ATSB 14.6 Abnormal Operations, Fail-Safes and Flight Termination 14.7 Operating Near Aerodromes and Above 400 ft AGL
6.2 Payload, Centre of Gravity and Pre-Flight Checks
Key Takeaways Explain This Topic AI
Adding payload increases total weight and may shift the centre of gravity, affecting control response, efficiency, and stability; always respect the manufacturer's maximum payload and MTOW.
The battery is often the heaviest item on a small RPA, so its position and secure mounting directly govern the centre of gravity.
Wind and density altitude (hot, humid, or elevated conditions) reduce lift and the spare performance margin; reduce payload or delay the flight when margin is thin.
A written pre-flight checklist covering airframe, battery, sensors, C2 link, geofence, home point, airspace, weather, and emergencies is mandatory before every flight.
Perform a hover check immediately after takeoff to verify control response, vibration, drift, and telemetry, and complete a post-flight log review to catch developing faults.
Last updated: August 2026
Payload, Centre of Gravity and Pre-Flight Checks
Adding a payload — a camera, a sensor pod, or a delivery package — changes the way an RPA flies. Weight increases the power required to hover, and a shifted centre of gravity (CoG) changes how the aircraft responds to control inputs. This section covers payload and CoG effects, the performance margin that wind and density altitude eat into, and the full pre-flight checklist a remote pilot must complete before every flight.
Payload Weight and Centre of Gravity
Payload is anything attached to the aircraft that was not part of its baseline design — cameras, gimbals, LiDAR units, crop-spray tanks, or parcels. Two effects matter:
Total weight — more weight means more lift required, higher motor current, shorter endurance, and reduced authority to recover from turbulence. Always respect the manufacturer's maximum payload and maximum take-off weight (MTOW); exceeding it is illegal under CASR Part 101 and unsafe.
Centre of gravity (CoG) — the point through which gravity acts on the aircraft. The flight controller is tuned for a specific CoG location. A payload that shifts the CoG forward, aft, or laterally causes:
One side or axis of motors to work harder, reducing efficiency and endurance.
Uneven control response — the aircraft may feel sluggish in one direction and twitchy in the other.
In extreme cases, the controller cannot maintain stable hover or level flight.
Balance the aircraft so the CoG sits at the manufacturer-specified location — usually marked on the airframe or documented in the flight manual. Hang-test or balance-test methods apply for multirotors and fixed-wing RPA respectively.
Battery Position and Balance
The battery is often the heaviest single item on a small RPA, so its position has a large influence on CoG. Always:
Mount the battery in the designated position and orient it as shown in the manual.
Use the correct battery type and capacity — a larger battery may fit physically but shift the CoG and exceed MTOW.
Secure the battery so it cannot shift in flight; a sliding battery changes CoG mid-flight and can destabilise the aircraft.
Wind and Density Altitude: Performance Margin
Every RPA has a performance margin — the spare lift and control authority available above what is needed to hover. Two environmental factors reduce that margin:
Wind — flying into a headwind reduces ground speed and extends time to return; crosswinds push the aircraft toward obstacles; gusts require sudden power spikes. Always check the forecast against the aircraft's documented maximum wind speed and never fly at or above that limit.
Density altitude — high temperature, high humidity, and high elevation all reduce air density, so the propellers produce less lift per revolution. On a hot day at an inland launch site, the aircraft may need noticeably more power to hover, shortening endurance and reducing the margin to recover from a gust.
Plan flights with margin: launch with enough battery reserve to return against the wind, and reduce payload or delay the flight when density altitude is high. A heavily loaded aircraft on a hot, windy day has very little spare performance — that is when accidents happen.
The Full Pre-Flight Checklist
A structured pre-flight check is mandatory, not optional. Use a written checklist every time — memory is not reliable. The table below sets out the items to verify before takeoff.
- Area Check
- Airframe Props undamaged, balanced, and secure; arms locked; no cracks; motors turn freely
- Battery Charge level sufficient for the planned flight; voltage per cell within limits; latched and secure
- GNSS 3D fix; satellite count sufficient; HDOP low (about 1.5 or better)
- Compass Calibrated; on-site interference check passed
- IMU Calibrated; no vibration warning; level on the ground
- Firmware Flight controller, battery, and ground station all current
- C2 link Range test completed; signal strong; failsafe behaviour confirmed
- Geofence Max height and radius set to match the operation
- Home point Recorded and correct on the ground station
- Airspace/NOTAM Current airspace checked; NOTAMs reviewed; approvals in place if required
- Weather Wind, temperature, and visibility within aircraft and operation limits
- Emergencies Forced-landing options identified; abort criteria agreed with any crew
Hover Check
Immediately after takeoff, perform a hover check before transiting away:
Hold a stable hover at eye level, a few metres in front of the pilot.
Confirm control response — pitch, roll, yaw, and throttle all react correctly and proportionally.
Watch for abnormal vibration or oscillation that was not visible on the ground.
Check for unexpected drift — a steady drift with no wind input suggests a sensor or compass problem.
Confirm the C2 link is solid and the ground station telemetry (height, battery, satellite count) is sensible.
If anything is abnormal, land immediately and investigate. A problem found at the hover check is almost always cheaper and safer than one found downrange.
Post-Flight Log Review
After landing, complete the loop:
Power down the aircraft and record the flight time and any incidents in the flight log .
Note any anomalies — link drops, compass warnings, unusual vibration, or battery behaviour — for maintenance follow-up.
Inspect the airframe, props, and motors for damage acquired during the flight.
If the operation is conducted under a ReOC, log the flight as required by the operator's procedures.
A disciplined post-flight review catches developing faults early and keeps the aircraft legal and airworthy for the next sortie.