Study guide

5.4 Magnetic Particle (MT), Liquid Penetrant (PT) & Personnel Qualification

AWS API 1104 Pipeline Welding Endorsement Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Overview & Scope of API 1104:2021

1.1 Scope, Definitions & General Requirements 1.2 Base Materials & Filler Metal Groupings

2 Chapter 2: Welding Procedure Qualification (Section 5)

2.1 Welding Procedure Specification (WPS) Requirements & Contents 2.2 Essential Variables for Procedure Qualification (Section 5.4) 2.3 Mechanical Testing Requirements and Specimen Preparation 2.4 Acceptance Criteria for Procedure Qualification

3 Chapter 3: Welder Qualification (Section 6)

3.1 Single Qualification Testing & Essential Variables 3.2 Multiple Qualification Testing & Layout 3.3 Visual & Destructive Test Specimen Layout 3.4 Acceptance Criteria & Retesting Rules for Welders

4 Chapter 4: Design & Fabrication of Pipeline Welds (Section 7)

4.1 Joint Alignment, High-Low & Fit-Up Tolerances 4.2 Preheating, Interpass Temperature & Heat Treatment 4.3 Tack Welding, Line-Up Clamps & Weather Restrictions 4.4 Filler Metal Storage, Handling & Conditioning

5 Chapter 5: Inspection & Non-Destructive Testing (Sections 8 & 11)

5.1 Rights & Responsibilities of Inspection Personnel 5.2 Radiographic Testing (RT) & Image Quality Indicators (IQI) 5.3 Ultrasonic Testing (UT) & Automated UT (AUT/PAUT) 5.4 Magnetic Particle (MT), Liquid Penetrant (PT) & Personnel Qualification

6 Chapter 6: Acceptance Standards for Imperfections (Section 9)

6.1 Inadequate Penetration (IP), IP Due to High-Low (IPD) & Cross Penetration (ICP) 6.2 Incomplete Fusion (IF & IFD), Internal Concavity (IC) & Burn-Through (BT) 6.3 Slag Inclusions (ESI & ISI) & Hollow Bead (HB) Porosity 6.4 Porosity — Scattered (P), Distribution Charts & Hollow Bead Cross-Reference 6.5 Undercutting, Crater Cracks & Arc Burns 6.6 Cracks, Accumulation of Imperfections & Annex A (ECA)

7 Chapter 7: Repair, Mechanized Welding & Records (Sections 10 & 12)

7.1 Repair Procedure Qualification & Limitations 7.2 Defect Removal, Grinding & Re-Inspection 7.3 Welding Records, Traceability & Inspector Logs 7.4 Mechanized Welding with Filler Metal Additions (Section 12)

8 Chapter 8: Annex B — In-Service Pipeline Welding

8.1 In-Service Welding Dynamics, Burn-Through & HIC Risks 8.2 Temper-Bead Deposition Techniques & Sequence 8.3 In-Service Procedure & Welder Qualification Requirements

5.4 Magnetic Particle (MT), Liquid Penetrant (PT) & Personnel Qualification

Key Takeaways Explain This Topic AI

API 1104 Section 11.2 invokes ASTM E709 for Magnetic Particle Testing, including yoke weight-lift verification: 10 lb (4.5 kg) for AC yokes and 40 lb (18.1 kg) for DC yokes at maximum pole spacing.

Liquid Penetrant Testing per Section 11.3 follows ASTM E165 and the qualified written procedure; penetrant and developer dwell times are procedure/manufacturer specified (commonly 10 to 30 minutes).

NDT personnel evaluating examination results must be certified to Level II or Level III under ASNT SNT-TC-1A, ANSI/ASNT CP-189, or an equivalent Company-recognized standard.

Level I NDT technicians are authorized to perform equipment setup and testing under direct Level II/III supervision, but cannot evaluate or sign off on final weld acceptance/rejection.

Written NDT procedures are mandatory for all examination methods (RT, UT, MT, PT) and must be qualified by testing and maintained on file by the inspection organization.

Last updated: August 2026

5.4 Magnetic Particle (MT), Liquid Penetrant (PT) & Personnel Qualification

While volumetric testing methods (RT and UT) detect internal weld discontinuities, surface non-destructive testing methods— Magnetic Particle Testing (MT) and Liquid Penetrant Testing (PT) —are essential for detecting surface-breaking cracks, lack of surface fusion, arc strikes, and bevel laminations. API Standard 1104 Sections 11.2 and 11.3 specify procedural standards for MT and PT, while Section 11 establishes mandatory qualification frameworks for all NDT personnel. Inspectors must master surface testing mechanics, equipment calibration thresholds, and technician certification boundaries.

1. Magnetic Particle Testing (MT) Procedures & Yoke Calibration

API 1104 Section 11.2 governs Magnetic Particle Testing, which is applicable exclusively to ferromagnetic materials (such as carbon steel pipeline grades).

Physical Operating Principle

When a magnetic field is introduced into a ferromagnetic pipe weld, surface-breaking or near-surface discontinuities disrupt the magnetic flux lines, causing magnetic flux leakage fields. Fine iron oxide particles applied to the surface are attracted to these leakage fields, forming visible indications pinpointing the flaw.

Equipment Techniques

AC electromagnetic Yokes: Alternating Current (AC) yokes induce strong surface magnetic fields. Due to the skin effect of AC current, AC yokes are exceptionally sensitive for detecting surface-breaking cracks and root flaws.

DC electromagnetic Yokes & Permanent Magnets: Direct Current (DC) yokes provide deeper magnetic field penetration, enabling detection of slightly subsurface discontinuities.

Prod Techniques: Direct contact prods passing high current through the pipe wall. Note: Prod techniques are restricted on high-strength pipeline steels due to the risk of arc burns on base metal.

Mandatory Yoke Lifting Power Verification

To verify sufficient magnetic field strength, ASTM E709 (invoked by Section 11.2) calls for periodic weight-lift verification using certified steel lift blocks at maximum pole spacing:

AC electromagnetic Yokes: Must demonstrate a minimum lifting power of 10 lbs (4.5 kg) .

DC electromagnetic Yokes: Must demonstrate a minimum lifting power of 40 lbs (18.1 kg) .

Frequency: Lifting power checks must be performed daily prior to use, or whenever a yoke experiences physical damage.

2. Liquid Penetrant Testing (PT) Procedure & Dwell Times

API 1104 Section 11.3 governs Liquid Penetrant Testing, which is utilized for detecting surface-breaking discontinuities on non-magnetic or ferromagnetic metals, fillet welds, branch connections, and stainless steel clad overlays.

Step-by-Step Solvent-Removable Visible Dye Process

Surface Preparation & Cleaning: Weld surface and adjacent base metal (1.0 in. on either side) must be thoroughly cleaned using solvent cleaner/remover to remove oil, grease, scale, paint, and rust. Surface must be allowed to thoroughly dry (minimum 1 to 5 minutes).

Penetrant Application & Dwell Time: Apply visible red dye penetrant by spraying, brushing, or flooding. Dwell Time is the duration the liquid penetrant remains on the weld to allow capillary action to draw dye into fine cracks.

Penetrant Dwell Time: set by the qualified procedure per ASTM E165 and the penetrant manufacturer — commonly 10 to 30 minutes depending on temperature and material.

Temperature Limits: Standard testing temperature range is 40°F to 125°F (4°C to 52°C) .

Excess Penetrant Removal: Wipe excess surface penetrant using clean, dry, lint-free cloths. Finish with cloths sparingly dampened with solvent remover. Direct flushing of the weld surface with solvent is strictly prohibited to prevent washing penetrant out of true flaws.

Developer Application & Dwell Time: Apply a thin, uniform spray layer of non-aqueous wet developer. Developer acts as a blotter, drawing trapped dye back to the surface to form expanded red indications against a white background.

Developer Dwell Time: 10 to 30 minutes (minimum 10 minutes, not exceeding 2 hours).

Visual Evaluation & Illumination: Examine the weld under adequate white light intensity (minimum 100 foot-candles / 1000 lux at the inspection surface).

3. NDT Personnel Qualification & Certification Framework

Section 11 mandates that all non-destructive examination personnel (RT, UT, MT, PT) must be qualified and certified in accordance with recognized national qualification programs:

Recognized Qualification Frameworks

ASNT SNT-TC-1A: American Society for Nondestructive Testing Recommended Practice.

ANSI/ASNT CP-189: ASNT Standard for Qualification and Certification of NDT Personnel.

ISO 9712 / CSWIP: Internationally recognized central certification schemes acceptable to the Company.

Three-Tier Level Authority Structure

Certification Level Scope of Authority & Operational Capabilities API 1104 Approval & Sign-Off Authority

NDT Level I Qualified to perform specific calibrations, equipment setups, and testing under direct supervision of Level II or Level III personnel. NO Sign-Off Authority. Cannot independently evaluate test results or sign formal acceptance/rejection reports.

NDT Level II Qualified to set up equipment, calibrate, perform examinations, interpret signals/images, and evaluate results directly against API 1104 Section 9 acceptance criteria. FULL Sign-Off Authority. Authorized to prepare, sign, and issue formal NDT inspection reports accepting or rejecting welds.

NDT Level III Qualified to establish and qualify NDT procedures, designate testing techniques, train/examine Level I and II personnel, and resolve technical disputes. AUTHORITATIVE Sign-Off. Highest technical authority; approves written NDT procedure specifications and audit logs.

Vision Examination Requirements for NDT Personnel

All NDT technicians (Level I, II, III) must pass annual vision tests:

Near-Vision Acuity: Jaeger J1 chart at not less than 12 in. (300 mm).

Color Perception: Ability to distinguish contrast between colors used in the specific NDT method.

4. NDT Documentation, Procedure Control & Record Retention

API 1104 requires complete traceability for all surface and volumetric NDT operations:

Written NDT Procedures: Every NDT method must be performed in accordance with a written, qualified procedure specification approved by an NDT Level III.

Examination Reports: Formal inspection records must document weld number, line section, date, NDT method, equipment serial numbers, surface condition, examiner printed name, certification level, signature, and explicit disposition (Accept/Reject per Section 9).

Record Retention: All NDT reports, radiographic films, and electronic UT data files must be retained by the Company for the service life of the pipeline or as specified by federal pipeline safety regulations (49 CFR 192/195).