Study guide
10.4 B31.1 Materials, Design Conditions & Pressure Design of Components
AWS ASME BPVC Section IX + B31.1/B31.3 Endorsement CWI/SCWI
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Structure, Logistics & Code Navigation Strategy
1.1 Credential Overview, Prometric Delivery & July 2025 Hard-Copy Rule 1.2 The Three-Code Triad: Section IX, B31.1, and B31.3 Roles & Interrelationships 1.3 Rapid Code-Book Navigation: Tabbing, Cross-Referencing & Time Management
2 Chapter 2: Section IX Article I — General Welding Requirements
2.1 Scope, Responsibilities & Section IX Architecture 2.2 Mechanical Test Types, Specimen Dimensions & Acceptance Criteria 2.3 Notch-Toughness Tests, Fillet-Weld Tests & Special Examinations
3 Chapter 3: Section IX Article II — Procedure Qualification Fundamentals
3.1 PQR vs. WPS Workflow, Purpose & Content Requirements 3.2 Coupling and Supporting Multiple WPSs and PQRs 3.3 Test Coupons, Preparation & Required Test Specimen Allocations
4 Chapter 4: Section IX Procedure Qualification Limits & Thickness Rules
4.1 Base Metal & Deposited Weld Metal Thickness Limits 4.2 Impact Testing Requirements & Toughness Thickness Qualification Ranges 4.3 Fillet Weld Procedure Qualification Rules & Special Applications
5 Chapter 5: Section IX Article III — Welder Performance Qualification Fundamentals
5.1 Welder & Welding Operator Qualification Intent, Responsibilities & Identification 5.2 Qualification Testing Methods: Mechanical Bend Tests vs. Volumetric NDE 5.3 Welder Qualification Continuity, Expiration, and Requalification
6 Chapter 6: Section IX Welder Performance Limits, Positions & Diameters
6.1 Test Positions, Groove Weld Orientations & Production Position Limits 6.2 Welder Thickness Limits and Pipe Diameter Qualification Ranges 6.3 Welder Essential Variables: F-Numbers, Backing, and Process Transfers
7 Chapter 7: Section IX Article IV — Welding Variables by Process (Part 1: SMAW & GTAW)
7.1 Understanding Essential, Supplementary Essential & Nonessential Variables 7.2 Shielded Metal Arc Welding (SMAW) Procedure Variables 7.3 Gas Tungsten Arc Welding (GTAW) Procedure Variables
8 Chapter 8: Section IX Article IV — Welding Variables by Process (Part 2: GMAW/FCAW & SAW)
8.1 GMAW & FCAW Procedure Variables and Short-Circuiting Transfer Rules 8.2 Submerged Arc Welding (SAW) Procedure Variables and Flux-Wire Combinations 8.3 Special Variables: Heat Input, Electrical Characteristics & Shielding Gases
9 Chapter 9: Section IX Material Classifications, Numbers & Standard Documentation
9.1 Base Metal P-Numbers, Group Numbers, and S-Numbers 9.2 Filler Metal F-Numbers and As-Deposited Chemistry A-Numbers 9.3 ASME Standard Documentation: Auditing WPS, PQR, and WPQ Forms
10 Chapter 10: ASME B31.1 Power Piping — Scope, Materials, Design & Welding Fabrication
10.1 B31.1 Scope, Jurisdiction, Boiler External Piping vs. Non-Boiler External Piping 10.2 B31.1 Welding Requirements, Joint Alignment, Backing Rings & Tack Welds 10.3 B31.1 Welder & Procedure Qualification Interfacing with Section IX 10.4 B31.1 Materials, Design Conditions & Pressure Design of Components
11 Chapter 11: ASME B31.1 Power Piping — Heat Treatment, Examination, Testing & Fabrication Records
11.1 B31.1 Preheat Rules & Mandatory Temperatures 11.2 B31.1 Postweld Heat Treatment (PWHT) Rules, Temperatures & Holding Times 11.3 B31.1 Mandatory NDE Examination, Acceptance Standards & Pressure Leak Tests 11.4 B31.1 Bending, Forming, Assembly & Code Records
12 Chapter 12: ASME B31.3 Process Piping — Scope, Fluid Services, Materials, Design & Welding
12.1 B31.3 Scope, Fluid Service Classifications & Owner Responsibilities 12.2 B31.3 Welding, Joint Preparation, Backing Rings & Fabrication Details 12.3 B31.3 Procedure & Performance Qualification Rules and Section IX Exceptions 12.4 B31.3 Materials, Design Conditions & Pressure Design of Components
13 Chapter 13: ASME B31.3 Process Piping — Heat Treatment, Examination, Testing, Fabrication & Records
13.1 B31.3 Preheat and Postweld Heat Treatment Rules & Tables 13.2 B31.3 Inspection vs. Examination Responsibilities & Examination Extents 13.3 B31.3 Acceptance Criteria for Weld Imperfections 13.4 B31.3 Pressure Leak Testing: Hydrostatic, Pneumatic & Sensitive Leak Tests 13.5 B31.3 Bending, Forming, Assembly & Records
10.4 B31.1 Materials, Design Conditions & Pressure Design of Components
Key Takeaways Explain This Topic AI
ASME B31.1 Eq. (3) in Para 104.1.2(A) computes the minimum required wall thickness as tm = PD / (2(SE + Py)) + A, where D is the outside diameter, SE is the allowable stress times the joint efficiency or casting quality factor from Appendix A, y is the coefficient from Table 104.1.2(A), and A is the additional thickness allowance.
The allowance A covers three separate things under Paras 102.4.1, 102.4.2, and 102.4.4: corrosion and erosion, material removed for threading or grooving, and added mechanical strength; it is not a single corrosion number.
Para 104.1.2(A.1.1) requires the calculated tm to be increased by the manufacturing tolerance of the applicable pipe specification, after which the next heavier commercial wall thickness is selected from ASME B36.10M.
Mandatory Appendix A supplies the allowable stress values, joint efficiency factors E, and casting quality factors F — SE or SF may never exceed the Appendix A value at the design temperature — while Table 126.1 lists the component standards and material specifications acceptable for B31.1 construction; components not covered by a listed standard must be qualified by the pressure design rules of Para 104.
Threaded steel pipe in steam service above 250 psi, or water service above 100 psi with water above 220°F, shall be seamless with a minimum ultimate tensile strength of 48,000 psi and a weight at least equal to Schedule 80 of ASME B36.10M.
Last updated: September 2026
10.4 B31.1 Materials, Design Conditions & Pressure Design of Components
The AWS endorsement's published test specifications reserve a Materials and Design content area of at least 5% of the exam, and B31.1 supplies the largest block of items on the paper. That combination makes the pressure design rules of Chapter II and the material rules of Chapter III worth tabbing even though they sit outside the welding chapters most inspectors live in. The questions are not design questions — no one expects a CWI to size a header — they are lookup and nomenclature questions: which symbol means what, which table supplies the value, and which allowance belongs where.
1. Design Conditions (Para 101)
Para 101 establishes the conditions the design must satisfy, and Para 104 then converts them into a wall thickness.
Internal Design Pressure (Para 101.2): Shall not be less than the maximum sustained operating pressure within the piping system, including the effect of static head of liquid. For Boiler External Piping, it must also satisfy Section I PG-58.
Design Temperature (Para 101.3): The expected maximum sustained metal temperature of the pipe wall.
Ambient and Dynamic Effects (Para 101.5 and Para 119): Fluid transients and water hammer, safety-valve discharge reaction, seismic and wind loading, and thermal expansion and contraction all feed the design, and thermal flexibility is analysed under Para 119.
2. Allowable Stresses and Mandatory Appendix A
B31.1 does not print allowable stresses in the body of the Code. They live in Mandatory Appendix A , indexed by material specification, grade, and design temperature. Three symbols matter for the endorsement:
- Symbol Meaning Where It Comes From
- S S S Maximum allowable stress in the material at the design temperature Appendix A
- E E E Weld joint efficiency factor for welded pipe (a seam quality factor) Appendix A
- F F F Casting quality factor for cast components Appendix A
S E SE SE or S F SF SF The product actually used in the thickness equation Appendix A — the tabulated values already include E E E or F F F
Para 104.1.2(A.5) is explicit: the value of S E SE SE or S F SF SF shall not exceed the Appendix A value for the respective material and design temperature, and S F SF SF is used in place of S E SE SE where casting quality factors are intended. A seamless pipe carries E = 1.00 E = 1.00 E = 1.00 ; an electric-resistance-welded or furnace-butt-welded pipe carries a lower factor, and that reduction is why the same nominal schedule can be adequate in one product form and inadequate in another.
3. Straight Pipe Under Internal Pressure: Para 104.1.2 Equation (3)
The core equation of B31.1 pressure design is Eq. (3) : t m = P D 2 ( S E + P y ) + A t_m = \frac{P D}{2\left(SE + P y\right)} + A t m = 2 ( SE + P y ) P D + A
- Symbol Definition
- t m t_m t m Minimum required wall thickness, in. (mm)
- P P P Internal design pressure, psig
- D D D Outside diameter of pipe, in. — from the tables of standards and specifications for design calculations
S E SE SE Maximum allowable stress including joint efficiency (or S F SF SF with the casting factor), psi, from Appendix A
y y y Coefficient from Table 104.1.2(A) , which varies with material and design temperature
A A A Additional thickness , in.
B31.1 also gives Eq. (3A) , the inside-diameter form, and Eqs. (4) and (4A) , which invert the relationship to find the allowable design pressure for a pipe of known minimum wall. The note to Eq. (4) permits the computed pressure to be rounded up to the next higher unit of 10.
Important
B31.1 uses D D D , the outside diameter, and y y y ; B31.3 uses D D D and Y Y Y plus a weld joint strength reduction
factor W W W and writes the allowance as c c c outside the fraction. Two codes, two nomenclatures, one exam. Tab
both equations and read the symbol list before substituting anything.
What the Allowance A A A Actually Covers
A A A is not a corrosion allowance. Para 104.1.2(A.6) breaks it into three independent contributions, each with its own cross-reference:
Material removed in threading, grooving, or similar operations required to make a mechanical joint — Para 102.4.2.
Added mechanical strength for the pipe — Para 102.4.4. B31.1 is careful to say this is not intended to cover extreme misapplied external loads or mechanical abuse.
Corrosion and/or erosion — Para 102.4.1.
Manufacturing Tolerance and Schedule Selection
Para 104.1.2(A.1.1) closes the loop between a calculated number and a purchasable pipe:
If pipe is ordered by its nominal wall thickness, the manufacturing tolerance on wall thickness must be taken into account. After the minimum pipe wall thickness t m t_m t m is determined by Eq. (3) or (3A), this minimum thickness shall be increased by an amount sufficient to provide the manufacturing tolerance allowed in the applicable pipe specification or required by the process. The next heavier commercial wall thickness shall then be selected from thickness schedules such as contained in ASME B36.10M. +-----------------------------------------------------------------------------------------+
- | FROM EQUATION TO PURCHASE ORDER (PARA 104.1.2) |
- +-----------------------------------------------------------------------------------------+
- | 1. Look up SE (and y) in Appendix A / Table 104.1.2(A) at the DESIGN temperature. |
- | 2. Compute t_m = PD / (2(SE + Py)) + A. |
- | 3. Increase t_m by the mill tolerance of the pipe specification (commonly 12.5% for |
- | seamless pipe, i.e. divide by 0.875). |
- | 4. Select the NEXT HEAVIER commercial schedule from ASME B36.10M. |
- | 5. Para 102.4.5: allow for thinning in bends; Para 102.4.6: allow for casting tolerance. |
- +-----------------------------------------------------------------------------------------+
Two related allowances complete the picture: Para 102.4.5 requires compensation for thinning on the extrados of bends, and Para 102.4.6 covers cast components.
Mandatory Minimums for Threaded Pipe (Para 104.1.2(C))
Even when the equation says a thinner wall would hold the pressure, B31.1 imposes floor requirements for mechanical strength:
Where steel pipe is threaded and used for steam service above 250 psi (1 750 kPa) , or for water service above 100 psi (700 kPa) with water temperature above 220°F (105°C) , the pipe shall be seamless , with a minimum ultimate tensile strength of 48,000 psi (330 MPa) and a weight at least equal to Schedule 80 of ASME B36.10M.
Threaded brass or copper pipe in those services shall have a wall thickness at least equal to that required above for steel pipe of corresponding size.
4. Other Pressure Design Rules in Para 104
Para 104 extends beyond straight pipe, and the CWI should know which sub-paragraph owns which geometry:
- Geometry Paragraph What It Controls
- Curved segments and bends 104.2.1 Wall thickness after bending, flattening and buckling limits
- Miter bends 104.3 (with Para 104.2) Angular limits and thickness for fabricated miters
- Branch connections 104.3.1 Reinforcement area, the reinforcement zone, and integrally reinforced fittings
- Closures, blanks, flanges, reducers 104.4 through 104.5 Pressure design of ends and transitions
- Pressure design of other components 104.7 Unlisted components qualified by analysis, proof test, or experience
For a welding inspector, the practical hook is Para 104.3.1 branch reinforcement : the reinforcing pad, saddle, or integrally reinforced fitting is a welded detail, and the inspector must confirm that the reinforcement actually installed matches the detail the designer credited.
5. Materials: Chapter III and Table 126.1
Chapter III (Paras 123 and 124) governs material requirements and temperature limitations. Table 126.1 is the list of specifications and standards — dimensional standards such as ASME B16.5, B16.9, B16.11, B16.25, and B36.10M, together with the ASTM and ASME material specifications — that are acceptable for B31.1 construction.
Two consequences follow directly:
Listed components manufactured to a Table 126.1 standard carry that standard's pressure-temperature ratings, and the designer may use those ratings without further calculation.
Unlisted components must be qualified by the pressure design rules of Para 104.7, which permit analysis, proof testing, or documented experience.
A jurisdictional wrinkle from Chapter 10.1 reappears here: for Boiler External Piping , materials must comply with Section I (ASME Section II SA or SB specifications), whereas for Non-Boiler External Piping, Table 126.1 permits certain ASTM materials that Section II has not adopted. An inspector auditing MTRs on a BEP spool checks against Section I; on an NBEP spool, against Table 126.1.
- 6. Worked Example and Exam Traps
- Worked Example: Reading the Equation Correctly
An NPS 8 header ( D = 8.625 in. D = 8.625\text{ in.} D = 8.625 in. ) of seamless SA-106 Grade B is designed for P = 600 psig P = 600\text{ psig} P = 600 psig at 700°F. From Appendix A, S E = 16,600 psi SE = 16{,}600\text{ psi} SE = 16 , 600 psi at 700°F (seamless, so E = 1.00 E = 1.00 E = 1.00 ). From Table 104.1.2(A), y = 0.4 y = 0.4 y = 0.4 for ferritic steel at this temperature. The specification allows a corrosion allowance of A = 0.0625 in. A = 0.0625\text{ in.} A = 0.0625 in. t m = 600 × 8.625 2 ( 16,600 + 600 × 0.4 ) + 0.0625 = 5,175 2 ( 16,840 ) + 0.0625 t_m = \frac{600 \times 8.625}{2\left(16{,}600 + 600 \times 0.4\right)} + 0.0625 = \frac{5{,}175}{2\left(16{,}840\right)} + 0.0625 t m = 2 ( 16 , 600 + 600 × 0.4 ) 600 × 8.625 + 0.0625 = 2 ( 16 , 840 ) 5 , 175 + 0.0625 t m = 5,175 33,680 + 0.0625 = 0.1536 + 0.0625 = 0.2161 in. t_m = \frac{5{,}175}{33{,}680} + 0.0625 = 0.1536 + 0.0625 = 0.2161\text{ in.} t m = 33 , 680 5 , 175 + 0.0625 = 0.1536 + 0.0625 = 0.2161 in.
Now apply Para 104.1.2(A.1.1). With a 12.5% mill tolerance, the ordered nominal wall must be at least 0.2161 / 0.875 = 0.247 in. 0.2161 / 0.875 = 0.247\text{ in.} 0.2161/0.875 = 0.247 in. Schedule 40 NPS 8 pipe is 0.322 in., which is the next heavier commercial wall and is therefore acceptable.
Common Exam Traps to Avoid
Inside vs. Outside Diameter: Eq. (3) uses D D D , the outside diameter. Eq. (3A) is the inside-diameter form and has a different denominator. Substituting the ID into Eq. (3) silently under-sizes the wall.
Forgetting the Mill Tolerance: t m t_m t m from the equation is a minimum wall , not an order thickness. The manufacturing tolerance must be added before selecting a schedule.
Treating A A A as a Corrosion Allowance Only: A A A bundles thread or groove depth, mechanical strength, and corrosion/erosion.
Assuming E = 1 E = 1 E = 1 : E E E is 1.00 only for seamless product. Welded pipe carries a lower joint efficiency, and Appendix A's tabulated S E SE SE already reflects it.
The Threaded-Pipe Floor: For steam over 250 psi or hot water over 100 psi, the answer is seamless, Schedule 80 minimum, 48,000 psi minimum UTS , regardless of what the equation computes.
Cross-Code Symbol Drift: B31.1's y y y and B31.3's Y Y Y are analogous but tabulated separately, and B31.3 adds a weld joint strength reduction factor W W W that B31.1 handles differently. Confirm which book the stem is asking about before you reach for a table.