Study guide
10.1 B31.1 Scope, Jurisdiction, Boiler External Piping vs. Non-Boiler External Piping
AWS ASME BPVC Section IX + B31.1/B31.3 Endorsement CWI/SCWI
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Structure, Logistics & Code Navigation Strategy
1.1 Credential Overview, Prometric Delivery & July 2025 Hard-Copy Rule 1.2 The Three-Code Triad: Section IX, B31.1, and B31.3 Roles & Interrelationships 1.3 Rapid Code-Book Navigation: Tabbing, Cross-Referencing & Time Management
2 Chapter 2: Section IX Article I — General Welding Requirements
2.1 Scope, Responsibilities & Section IX Architecture 2.2 Mechanical Test Types, Specimen Dimensions & Acceptance Criteria 2.3 Notch-Toughness Tests, Fillet-Weld Tests & Special Examinations
3 Chapter 3: Section IX Article II — Procedure Qualification Fundamentals
3.1 PQR vs. WPS Workflow, Purpose & Content Requirements 3.2 Coupling and Supporting Multiple WPSs and PQRs 3.3 Test Coupons, Preparation & Required Test Specimen Allocations
4 Chapter 4: Section IX Procedure Qualification Limits & Thickness Rules
4.1 Base Metal & Deposited Weld Metal Thickness Limits 4.2 Impact Testing Requirements & Toughness Thickness Qualification Ranges 4.3 Fillet Weld Procedure Qualification Rules & Special Applications
5 Chapter 5: Section IX Article III — Welder Performance Qualification Fundamentals
5.1 Welder & Welding Operator Qualification Intent, Responsibilities & Identification 5.2 Qualification Testing Methods: Mechanical Bend Tests vs. Volumetric NDE 5.3 Welder Qualification Continuity, Expiration, and Requalification
6 Chapter 6: Section IX Welder Performance Limits, Positions & Diameters
6.1 Test Positions, Groove Weld Orientations & Production Position Limits 6.2 Welder Thickness Limits and Pipe Diameter Qualification Ranges 6.3 Welder Essential Variables: F-Numbers, Backing, and Process Transfers
7 Chapter 7: Section IX Article IV — Welding Variables by Process (Part 1: SMAW & GTAW)
7.1 Understanding Essential, Supplementary Essential & Nonessential Variables 7.2 Shielded Metal Arc Welding (SMAW) Procedure Variables 7.3 Gas Tungsten Arc Welding (GTAW) Procedure Variables
8 Chapter 8: Section IX Article IV — Welding Variables by Process (Part 2: GMAW/FCAW & SAW)
8.1 GMAW & FCAW Procedure Variables and Short-Circuiting Transfer Rules 8.2 Submerged Arc Welding (SAW) Procedure Variables and Flux-Wire Combinations 8.3 Special Variables: Heat Input, Electrical Characteristics & Shielding Gases
9 Chapter 9: Section IX Material Classifications, Numbers & Standard Documentation
9.1 Base Metal P-Numbers, Group Numbers, and S-Numbers 9.2 Filler Metal F-Numbers and As-Deposited Chemistry A-Numbers 9.3 ASME Standard Documentation: Auditing WPS, PQR, and WPQ Forms
10 Chapter 10: ASME B31.1 Power Piping — Scope, Materials, Design & Welding Fabrication
10.1 B31.1 Scope, Jurisdiction, Boiler External Piping vs. Non-Boiler External Piping 10.2 B31.1 Welding Requirements, Joint Alignment, Backing Rings & Tack Welds 10.3 B31.1 Welder & Procedure Qualification Interfacing with Section IX 10.4 B31.1 Materials, Design Conditions & Pressure Design of Components
11 Chapter 11: ASME B31.1 Power Piping — Heat Treatment, Examination, Testing & Fabrication Records
11.1 B31.1 Preheat Rules & Mandatory Temperatures 11.2 B31.1 Postweld Heat Treatment (PWHT) Rules, Temperatures & Holding Times 11.3 B31.1 Mandatory NDE Examination, Acceptance Standards & Pressure Leak Tests 11.4 B31.1 Bending, Forming, Assembly & Code Records
12 Chapter 12: ASME B31.3 Process Piping — Scope, Fluid Services, Materials, Design & Welding
12.1 B31.3 Scope, Fluid Service Classifications & Owner Responsibilities 12.2 B31.3 Welding, Joint Preparation, Backing Rings & Fabrication Details 12.3 B31.3 Procedure & Performance Qualification Rules and Section IX Exceptions 12.4 B31.3 Materials, Design Conditions & Pressure Design of Components
13 Chapter 13: ASME B31.3 Process Piping — Heat Treatment, Examination, Testing, Fabrication & Records
13.1 B31.3 Preheat and Postweld Heat Treatment Rules & Tables 13.2 B31.3 Inspection vs. Examination Responsibilities & Examination Extents 13.3 B31.3 Acceptance Criteria for Weld Imperfections 13.4 B31.3 Pressure Leak Testing: Hydrostatic, Pneumatic & Sensitive Leak Tests 13.5 B31.3 Bending, Forming, Assembly & Records
10.1 B31.1 Scope, Jurisdiction, Boiler External Piping vs. Non-Boiler External Piping
Key Takeaways Explain This Topic AI
ASME B31.1 governs power and auxiliary service piping systems in electric generating stations, industrial plants, central and district heating plants, and institutional facilities, covering high-pressure steam, water, oil, gas, and air services.
Boiler External Piping (BEP) represents the legal and jurisdictional boundary between ASME BPVC Section I and ASME B31.1, extending from the boiler proper up to the required isolation valve(s) defined in ASME Section I PG-58 and B31.1 Figure 100.1.2.
BEP is legally part of the boiler: design, fabrication, and installation must satisfy ASME Section I administrative rules, requiring an ASME 'S', 'A', or 'PP' Code Symbol Stamp, an Authorized Inspector (AI) third-party inspection, and registration on ASME Manufacturer's Data Report Form P-4A.
Non-Boiler External Piping (NBEP) encompasses all piping downstream or beyond the terminal BEP isolation valves; it is governed entirely by ASME B31.1 and does not require ASME Code stamping, National Board registration, or an Authorized Inspector (unless mandated by local jurisdictional laws).
Design conditions under Para 101 require piping systems to withstand coincident maximum internal design pressure, maximum design temperature, and severe dynamic loading mechanisms including water hammer, relief valve reaction forces, seismic accelerations, and thermal expansion strains.
Last updated: September 2026
10.1 B31.1 Scope, Jurisdiction, Boiler External Piping vs. Non-Boiler External Piping
Core Principle: In power plant engineering and high-pressure steam facility construction, understanding where the jurisdiction of ASME Boiler and Pressure Vessel Code (BPVC) Section I ends and ASME B31.1 begins is the single most tested administrative concept on the AWS ASME Endorsement exam. While both codes govern high-energy piping, Boiler External Piping (BEP) creates a hybrid regulatory regime that merges Section I administrative stamping and inspection rules with B31.1 technical design and welding requirements.
1. Scope and Industrial Applications of ASME B31.1 (Para 100.1)
ASME B31.1 Power Piping is one of the foundational pressure piping codes in the ASME B31 series. Paragraph 100.1.1 defines the scope of B31.1 as prescribing minimum requirements for the design, materials, fabrication, erection, test, inspection, operation, and maintenance of power and auxiliary service piping systems .
Industrial Facilities Governed by B31.1
The standard specifically applies to piping in:
Electric Generating Stations: Thermal power plants (coal, pulverized fuel, combined cycle gas turbine [CCGT], heat recovery steam generators [HRSGs], biomass, and solar thermal generation), as well as the conventional secondary (balance-of-plant) steam and water loops of nuclear facilities.
Industrial and Manufacturing Plants: Chemical plants, paper mills, automotive plants, petroleum refineries, and manufacturing facilities where piping connects to high-pressure boilers or cogeneration steam turbines.
Institutional Heating Plants: Central utility plants at universities, hospital complexes, military installations, and government facilities.
Central and District Heating Systems: High-temperature hot water and high-pressure steam transmission and distribution networks routed between central plants and multiple consumer buildings.
Fluid Services Within B31.1 Scope
B31.1 regulates piping conveying:
Superheated and saturated steam at all pressures and temperatures.
Boiler feedwater, condensate return, and boiler blowoff/blowdown.
Fuel oil, natural gas, pulverized fuel slurries, and burner supply systems within the plant boundary.
Air, inert gas, hydraulic fluid, cooling water, and general auxiliary utility fluids.
Explicit Exclusions from ASME B31.1 (Para 100.1.3)
Inspectors must recognize systems that fall outside B31.1 jurisdiction:
Boiler Proper: Tubes, drums, downcomers, economizers, and superheater headers directly governed by ASME BPVC Section I.
Pressure Vessels & Heat Exchangers: Governed by ASME Section VIII Division 1, 2, or 3.
Building Services: Low-pressure plumbing, domestic potable water, sanitary waste, and building HVAC systems governed by the International Plumbing Code (IPC) or ASME B31.9 ( Building Services Piping ).
Process Piping: Chemical process piping, refining loops, and petrochemical transfer lines governed by ASME B31.3 ( Process Piping ).
Pipeline Transportation Systems: Cross-country liquid petroleum pipelines (ASME B31.4) and natural gas transmission/distribution pipelines (ASME B31.8).
2. The Great Jurisdictional Boundary: Section I vs. B31.1 (Figure 100.1.2)
One of the most critical sections in B31.1 is Paragraph 100.1.2 and its accompanying illustration, Figure 100.1.2 ( Code Jurisdictional Limits for Piping - Drum-Type and Forced-Flow Steam Generators ). This section delineates the legal boundary between:
- Boiler Proper (ASME Section I)
- Boiler External Piping (BEP) (ASME Section I administrative rules + ASME B31.1 technical rules)
Non-Boiler External Piping (NBEP) (ASME B31.1 entirely) +-----------------------------------------------------------------------------------------+
- | JURISDICTIONAL TRILOGY: BOILER PROPER, BEP & NBEP |
- +-----------------------------------------------------------------------------------------+
- | 1. BOILER PROPER (ASME Section I) |
- | - Steam drums, mud drums, waterwall tubes, downcomers, superheater/reheater coils. |
- | - Governed 100% by ASME Section I (Design, Materials, Welding, Stamping, AI). |
- |-----------------------------------------------------------------------------------------|
- | 2. BOILER EXTERNAL PIPING / BEP (ASME Section I Administrative + B31.1 Technical) |
- | - Piping from the boiler proper up to and including the terminal isolation valve(s). |
- | - Design, materials, fabrication, and erection reference ASME B31.1 Para 122.1. |
- | - BUT requires ASME Section I 'S', 'A', or 'PP' Stamp, Authorized Inspector (AI), |
- | and registration on ASME Manufacturer's Data Report Form P-4A! |
- |-----------------------------------------------------------------------------------------|
- | 3. NON-BOILER EXTERNAL PIPING / NBEP (ASME B31.1 Entirely) |
- | - All piping systems downstream or outside the terminal isolation valves of BEP. |
- | - Governed 100% by ASME B31.1 (Chapters I through VI). |
- | - NO ASME Code Stamp required; NO Authorized Inspector (AI) mandated by ASME; |
- | no National Board Data Report required (unless local jurisdictional law mandates). |
- +-----------------------------------------------------------------------------------------+
- Terminal Isolation Valve Points for Boiler External Piping (BEP)
Per ASME Section I Paragraph PG-58 and ASME B31.1 Paragraph 122.1 , BEP encompasses all piping connecting the boiler proper to the following specific boundary valves:
Main Steam Piping (Steam Outlets):
Single Boiler System: Extends from the drum or superheater outlet nozzle up to and including the first stop valve .
Multiple Boilers Connected to a Common Header: When two or more boilers with manhole openings connect to a common steam header, Section I PG-58.3.1 and B31.1 Para 122.1.7 mandate two stop valves in series , with an ample free-blow drain valve located between them. In this scenario, BEP extends up to and includes the second stop valve !
Boiler Feedwater Piping:
Extends from the economizer inlet or steam drum feedwater nozzle backward to and including the stop valve and check valve nearest the boiler.
The stop valve must be installed between the check valve and the boiler to permit servicing the check valve while the boiler is depressurized.
Boiler Blowoff and Blowdown Piping:
Extends from the lowest water space, mud drum, or waterwall bottom headers up to and including the second valve .
For boilers with design pressures exceeding 100 psig (700 kPa), the blowoff system must have either two slow-opening valves in series, or one slow-opening valve combined with one quick-opening valve/cock (Para 122.1.4).
Drain, Vent, and Instrument Lines:
Water columns, gauge glasses, pressure gauge piping, vent lines, and drain connections up to and including their required isolation shutoff valves.
3. Administrative and Technical Comparison: BEP vs. NBEP
The table below summarizes the vital code distinctions between Boiler External Piping and Non-Boiler External Piping. CWI and SCWI candidates must commit these distinctions to memory.
- Regulatory Dimension Boiler External Piping (BEP) Non-Boiler External Piping (NBEP)
- Governing Primary Code ASME Section I (PG-58) via reference to B31.1 ASME B31.1 (Chapters I through VI)
- Technical Rules (Welding/Fab) ASME B31.1 (Para 122.1 & Chapter V) ASME B31.1 (Chapter V)
ASME Code Symbol Stamping MANDATORY : Requires 'S' , 'A' , or 'PP' Stamp NOT PERMITTED / NOT REQUIRED by ASME B31.1
Third-Party Inspection MANDATORY : Authorized Inspector (AI) commissioned by NB Quality Control by Fabricator / Owner Inspector (Para 136)
ASME Manufacturer's Data Report MANDATORY : Form P-4A (or P-2/P-3 by boiler mfr.) None required by ASME; MTRs and shop certs only
National Board Registration Mandatory registration with the National Board Not registered with National Board
Quality Assurance Program ASME-accredited QA system audited by ASME/AI Contractor/Owner QA program meeting B31.1
- Welding Procedures (WPS/PQR) ASME Section IX qualified ASME Section IX qualified (or permitted AWS SWPS)
- Welder Qualification (WPQ) ASME Section IX qualified ASME Section IX qualified (or permitted AWS SWPS)
- The Role of the Authorized Inspector (AI) in BEP
The Authorized Inspector (AI) is an independent, third-party inspector employed by an Authorized Inspection Agency (AIA)—typically an insurance company licensed to write boiler and pressure vessel insurance, or a jurisdictional state/provincial authority. For BEP, the AI must:
Verify that the fabricator holds a valid ASME Certificate of Authorization with an 'S', 'A', or 'PP' stamp.
Review and verify all WPSs, PQRs, and Welder Performance Qualifications (WPQs) prior to welding.
Perform witness and hold-point inspections on fit-up, root pass, backgouging, and completed welds.
Verify non-destructive examination (NDE) reports and PWHT charts.
Witness mandatory hydrostatic pressure tests (Section I PG-99 / B31.1 Para 137).
Countersign the ASME Manufacturer's Data Report Form P-4A before the piping receives the official ASME Code symbol stamp.
For NBEP, an ASME-commissioned AI has no legal jurisdiction under the ASME Code. Quality control and examination are performed by the manufacturer's or contractor's quality personnel (examiners), with owner oversight handled by the Owner's Inspector under Paragraph 136.1.
4. Design Conditions and Operating Loadings (Para 101)
Paragraph 101 establishes the baseline design requirements for power piping systems. Inspectors and welding engineers must understand these parameters because they dictate material selection, joint design, preheat, and postweld heat treatment.
1. Design Pressure (Para 101.2)
The internal design pressure shall not be less than the maximum sustained operating pressure within the piping system, including the effects of static head of liquid.
For BEP, the design pressure must match or exceed the highest safety valve set pressure on the boiler proper per Section I PG-58.3.
2. Design Temperature (Para 101.3)
The design temperature is defined as the expected maximum metal temperature of the pipe wall under sustained operating conditions.
For uninsulated pipes conveying hot fluids, the metal temperature may be calculated as a reduced percentage of fluid temperature, but for insulated lines, metal temperature is taken as 100% of fluid temperature.
3. Dynamic and Environmental Effects (Para 101.5)
Power piping must be engineered to resist extreme transient loadings:
Fluid Transients / Water Hammer (Para 101.5.1): Rapid valve closures, steam collapse in subcooled condensate, and pump trips generate massive shockwaves (pressure spikes) that can tear piping from supports or fracture brittle root welds.
Relief Valve Discharge Reaction Forces (Para 101.5.2 & Appendix II): When open-discharge safety valves pop, the sonic velocity steam jet creates instantaneous thrust reaction forces reaching tens of thousands of pounds, producing massive bending moments on branch connections.
Seismic Loads (Para 101.5.3): Dynamic accelerations calculated in accordance with ASCE 7 or building code criteria.
Wind Loads (Para 101.5.4): Applied to exterior elevated pipe racks, steam stacks, and HRSG exhaust ducts.
Thermal Expansion & Contraction (Para 119): Severe temperature excursions (ambient to 1,050°F [565°C] in main steam lines) produce substantial linear growth. Piping flexibility must be achieved via expansion loops, offsets, cold spring, and engineered spring hangers to prevent overstressing turbine and boiler nozzles.
5. Practical Inspection Scenarios & Exam Traps
Trap 1: The 'PP' Stamp on NBEP Fallacy: An exam question asks: "A contractor is fabricating high-pressure steam piping located 50 feet downstream of the main steam stop valve in a turbine building. Does ASME B31.1 require an ASME 'PP' stamp and an Authorized Inspector?" The answer is NO . Downstream of the terminal stop valve, the piping is NBEP . NBEP is governed strictly by B31.1, which does not mandate an ASME Code stamp or an Authorized Inspector.
Trap 2: Multi-Boiler Steam Header Boundary: Watch out for questions involving two or more boilers manifolded into a common steam header. If the question mentions that the boilers have manhole openings, the BEP boundary does not stop at the first valve—it extends up to and includes the second stop valve with an intervening drain!
Trap 3: Who May Sign Form P-4A: Only a designated representative of the ASME Certificate of Authorization holder ('S', 'A', or 'PP') and an Authorized Inspector (AI) holding an active National Board commission may sign the Form P-4A Data Report. An AWS Certified Welding Inspector (CWI) cannot sign Form P-4A unless they are also a commissioned AI.
Trap 4: Material Specification Differences: In BEP, all materials must comply with Section I (ASME Section II SA or SB specifications). In NBEP, ASME B31.1 Table 126.1 allows certain standard ASTM materials that have not been formally adopted into Section II.