Study guide

13.3 B31.3 Acceptance Criteria for Weld Imperfections

AWS ASME BPVC Section IX + B31.1/B31.3 Endorsement CWI/SCWI

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Structure, Logistics & Code Navigation Strategy

1.1 Credential Overview, Prometric Delivery & July 2025 Hard-Copy Rule 1.2 The Three-Code Triad: Section IX, B31.1, and B31.3 Roles & Interrelationships 1.3 Rapid Code-Book Navigation: Tabbing, Cross-Referencing & Time Management

2 Chapter 2: Section IX Article I — General Welding Requirements

2.1 Scope, Responsibilities & Section IX Architecture 2.2 Mechanical Test Types, Specimen Dimensions & Acceptance Criteria 2.3 Notch-Toughness Tests, Fillet-Weld Tests & Special Examinations

3 Chapter 3: Section IX Article II — Procedure Qualification Fundamentals

3.1 PQR vs. WPS Workflow, Purpose & Content Requirements 3.2 Coupling and Supporting Multiple WPSs and PQRs 3.3 Test Coupons, Preparation & Required Test Specimen Allocations

4 Chapter 4: Section IX Procedure Qualification Limits & Thickness Rules

4.1 Base Metal & Deposited Weld Metal Thickness Limits 4.2 Impact Testing Requirements & Toughness Thickness Qualification Ranges 4.3 Fillet Weld Procedure Qualification Rules & Special Applications

5 Chapter 5: Section IX Article III — Welder Performance Qualification Fundamentals

5.1 Welder & Welding Operator Qualification Intent, Responsibilities & Identification 5.2 Qualification Testing Methods: Mechanical Bend Tests vs. Volumetric NDE 5.3 Welder Qualification Continuity, Expiration, and Requalification

6 Chapter 6: Section IX Welder Performance Limits, Positions & Diameters

6.1 Test Positions, Groove Weld Orientations & Production Position Limits 6.2 Welder Thickness Limits and Pipe Diameter Qualification Ranges 6.3 Welder Essential Variables: F-Numbers, Backing, and Process Transfers

7 Chapter 7: Section IX Article IV — Welding Variables by Process (Part 1: SMAW & GTAW)

7.1 Understanding Essential, Supplementary Essential & Nonessential Variables 7.2 Shielded Metal Arc Welding (SMAW) Procedure Variables 7.3 Gas Tungsten Arc Welding (GTAW) Procedure Variables

8 Chapter 8: Section IX Article IV — Welding Variables by Process (Part 2: GMAW/FCAW & SAW)

8.1 GMAW & FCAW Procedure Variables and Short-Circuiting Transfer Rules 8.2 Submerged Arc Welding (SAW) Procedure Variables and Flux-Wire Combinations 8.3 Special Variables: Heat Input, Electrical Characteristics & Shielding Gases

9 Chapter 9: Section IX Material Classifications, Numbers & Standard Documentation

9.1 Base Metal P-Numbers, Group Numbers, and S-Numbers 9.2 Filler Metal F-Numbers and As-Deposited Chemistry A-Numbers 9.3 ASME Standard Documentation: Auditing WPS, PQR, and WPQ Forms

10 Chapter 10: ASME B31.1 Power Piping — Scope, Materials, Design & Welding Fabrication

10.1 B31.1 Scope, Jurisdiction, Boiler External Piping vs. Non-Boiler External Piping 10.2 B31.1 Welding Requirements, Joint Alignment, Backing Rings & Tack Welds 10.3 B31.1 Welder & Procedure Qualification Interfacing with Section IX 10.4 B31.1 Materials, Design Conditions & Pressure Design of Components

11 Chapter 11: ASME B31.1 Power Piping — Heat Treatment, Examination, Testing & Fabrication Records

11.1 B31.1 Preheat Rules & Mandatory Temperatures 11.2 B31.1 Postweld Heat Treatment (PWHT) Rules, Temperatures & Holding Times 11.3 B31.1 Mandatory NDE Examination, Acceptance Standards & Pressure Leak Tests 11.4 B31.1 Bending, Forming, Assembly & Code Records

12 Chapter 12: ASME B31.3 Process Piping — Scope, Fluid Services, Materials, Design & Welding

12.1 B31.3 Scope, Fluid Service Classifications & Owner Responsibilities 12.2 B31.3 Welding, Joint Preparation, Backing Rings & Fabrication Details 12.3 B31.3 Procedure & Performance Qualification Rules and Section IX Exceptions 12.4 B31.3 Materials, Design Conditions & Pressure Design of Components

13 Chapter 13: ASME B31.3 Process Piping — Heat Treatment, Examination, Testing, Fabrication & Records

13.1 B31.3 Preheat and Postweld Heat Treatment Rules & Tables 13.2 B31.3 Inspection vs. Examination Responsibilities & Examination Extents 13.3 B31.3 Acceptance Criteria for Weld Imperfections 13.4 B31.3 Pressure Leak Testing: Hydrostatic, Pneumatic & Sensitive Leak Tests 13.5 B31.3 Bending, Forming, Assembly & Records

13.3 B31.3 Acceptance Criteria for Weld Imperfections

Key Takeaways Explain This Topic AI

In ASME B31.3 Table 341.3.2, Symbol A represents absolute zero tolerance (none permitted) for cracks and lack of fusion across ALL fluid service categories.

Criterion B in Table 341.3.2 is a cumulative-length limit only: incomplete penetration is limited to 38 mm (1.5 in.) in any 150 mm (6 in.) of weld length or 25% of the total weld length, whichever is less. There is no depth allowance attached to Criterion B.

Undercut is Criterion H at a depth of 1 mm (1/32 in.) and Tw/4, whichever is less, or Criterion I at 1.5 mm (1/16 in.) and Tw/4; both carry the same 38 mm in 150 mm or 25% cumulative-length limit.

Weld reinforcement and internal root protrusion limits in Table 341.3.2 are graduated by nominal thickness Tw: 1/16 in. for Tw <= 1/4 in.; 1/8 in. for 1/4 in. < Tw <= 1/2 in.; 5/32 in. for 1/2 in. < Tw <= 1 in.; and 3/16 in. for Tw > 1 in.

Severe Cyclic Conditions requires completely smooth weld transitions merging flush with base metal surfaces to eliminate notch-induced stress concentrations.

Last updated: September 2026

13.3 B31.3 Acceptance Criteria for Weld Imperfections

In ASME B31.3, the definitive standard governing weld quality is Table 341.3.2 (Acceptance Criteria for Welds - Visual and Radiographic/Ultrasonic Examination) . Every Certified Welding Inspector evaluating process piping spools must be capable of translating the letter symbols in Table 341.3.2 into exact physical dimensions and pass/fail determinations.

Table 341.3.2 structures acceptance criteria using an alphanumeric coding scheme: rows represent specific weld imperfection types, columns represent fluid service categories (Normal, Category D, Severe Cyclic), and grid intersections contain Criterion Value Notes (Symbols A through M) that define allowable limits.

Decoding Table 341.3.2 Criterion Value Notes (Symbols A through M)

Table 341.3.2 itself contains no numbers . It is a grid: rows are weld imperfection types, columns are combinations of weld type and service condition (Normal and Category M Fluid Service; Severe Cyclic Conditions; Category D Fluid Service), and each cell holds a letter . The numbers live in the companion list, Criterion Value Notes for Table 341.3.2 . Learn the letters and you can answer any cell.

  • Symbol Criterion Measure Acceptable Value Limit
  • A Extent of imperfection Zero (no evident imperfection)

B Cumulative length of incomplete penetration ≤ 38 mm \le 38\text{ mm} ≤ 38 mm ( 1.5 in. 1.5\text{ in.} 1.5 in. ) in any 150 mm 150\text{ mm} 150 mm ( 6 in. 6\text{ in.} 6 in. ) weld length, or 25% of total weld length, whichever is less

C Cumulative length of lack of fusion and incomplete penetration ≤ 38 mm \le 38\text{ mm} ≤ 38 mm ( 1.5 in. 1.5\text{ in.} 1.5 in. ) in any 150 mm 150\text{ mm} 150 mm ( 6 in. 6\text{ in.} 6 in. ) weld length, or 25% of total weld length, whichever is less

D Size and distribution of rounded indications Per ASME BPVC Section VIII, Division 1, Mandatory Appendix 4

E Size and distribution of rounded indications For T w ≤ 1 / 4 in. T_w \le 1/4\text{ in.} T w ​ ≤ 1/4 in. ( 6 mm 6\text{ mm} 6 mm ), the limit is the same as D ; for T w > 1 / 4 in. T_w > 1/4\text{ in.} T w ​ > 1/4 in. , the limit is 1.5 × D

F Linear indications (tighter set) Individual length ≤ T w / 3 \le T_w/3 ≤ T w ​ /3 ; individual width ≤ 3 / 32 in. \le 3/32\text{ in.} ≤ 3/32 in. ( 2.5 mm 2.5\text{ mm} 2.5 mm ) and ≤ T w / 3 \le T_w/3 ≤ T w ​ /3 ; cumulative length ≤ T w \le T_w ≤ T w ​ in any 12 T w 12T_w 12 T w ​ of weld

G Linear indications (standard set) Individual length ≤ T w \le T_w ≤ T w ​ ; individual width ≤ 1 / 8 in. \le 1/8\text{ in.} ≤ 1/8 in. ( 3 mm 3\text{ mm} 3 mm ) and ≤ T w / 2 \le T_w/2 ≤ T w ​ /2 ; cumulative length ≤ 4 T w \le 4T_w ≤ 4 T w ​ in any 150 mm 150\text{ mm} 150 mm ( 6 in. 6\text{ in.} 6 in. )

H Depth and length of undercut Depth ≤ 1 / 32 in. \le 1/32\text{ in.} ≤ 1/32 in. ( 1 mm 1\text{ mm} 1 mm ) and ≤ T w / 4 \le T_w/4 ≤ T w ​ /4 ; cumulative length ≤ 38 mm \le 38\text{ mm} ≤ 38 mm in any 150 mm 150\text{ mm} 150 mm , or 25% of total, whichever is less

I Depth and length of undercut (relaxed) Depth ≤ 1 / 16 in. \le 1/16\text{ in.} ≤ 1/16 in. ( 1.5 mm 1.5\text{ mm} 1.5 mm ) and ≤ T w / 4 \le T_w/4 ≤ T w ​ /4 (or 1 / 32 in. 1/32\text{ in.} 1/32 in. ); same cumulative length limit as H

J Surface roughness ≤ 500 μ in. \le 500\ \mu\text{in.} ≤ 500 μ in. ( 12.5 μ m 12.5\ \mu\text{m} 12.5 μ m ) R a R_a R a ​ in accordance with ASME B46.1

K Depth of surface concavity, root concavity, or burn-through Total joint thickness, including weld reinforcement , ≥ T w \ge T_w ≥ T w ​

L Height of reinforcement or internal protrusion Graduated by T w T_w T w ​ (table below); weld metal shall merge smoothly into the component surfaces

M Height of reinforcement or internal protrusion Twice the value applicable for L

Two definitions control every calculation above:

T w T_w T w ​ is the nominal wall thickness of the thinner of two components joined by a butt weld.

Where two limiting values are separated by " and ," the lesser value determines acceptance; where two sets of values are separated by " or ," the larger value is acceptable.

  • Important
  • Criterion B has no depth component. Incomplete penetration under Criterion B is judged only on cumulative

length — 1.5 in. in any 6 in. of weld, or 25% of the total weld length, whichever is less. Any option that adds

"depth not exceeding 1/32 in. or 0.2 T w T_w T w ​ " to Criterion B is inventing a limit that Table 341.3.2 does not

contain. The same is true of Criterion C, which bundles lack of fusion with incomplete penetration under one

cumulative-length allowance.

How the Columns Move the Letters

The same imperfection row carries different letters in different columns, and that is the entire mechanism of the table:

Cracks and lack of fusion are Criterion A — zero — in every column , including Category D.

Severe Cyclic Conditions tightens rows relative to Normal Fluid Service: linear indications move from the Criterion G limits to the much tighter Criterion F limits, and rows that carry a numeric allowance in Normal service can be reassigned to A (zero).

Category D Fluid Service relaxes rows relative to Normal service, for example moving undercut from Criterion H (1/32 in.) to Criterion I (1/16 in.).

N/A in a cell means the Code does not establish acceptance criteria for that imperfection in that weld type and service — it does not mean "accept anything."

Because the letters move, the reliable open-book method is: find the row (imperfection), find the column (weld type and service condition), read the letter, then look the letter up in the Criterion Value Notes. Do not memorize a single numeric answer per imperfection.

  • In-Depth Analysis of Critical Imperfection Limits
  • 1. Cracks and Lack of Fusion (Symbol A)

For both cracks and lack of fusion, ASME B31.3 enforces Symbol A (zero tolerance) across all services without exception.

Metallurgical Reason: Cracks and planar unbonded interfaces represent acute, sharp notches with infinite theoretical stress concentration factors ( K t → ∞ K_t \to \infty K t ​ → ∞ ). Under internal pressure, thermal cycling, or fluid pulsation, cracks propagate rapidly according to linear elastic fracture mechanics principles (stress intensity factor K I > K I C K_I > K_{IC} K I ​ > K I C ​ ).

Exam Application: If a question asks for the allowable length or depth of a crack or lack of fusion in Category D, Normal, or Severe Cyclic piping, the answer is always ZERO .

2. Incomplete Penetration (Symbol B vs. Symbol A)

Incomplete penetration (IP) occurs when weld metal fails to penetrate to the root of the joint:

In Normal Fluid Service: B31.3 recognizes that in non-cyclic, low-fatigue environments, a limited amount of root incomplete penetration does not immediately threaten the joint. Under Criterion B , IP is acceptable provided the cumulative length does not exceed 1.5 in. (38 mm) in any 6 in. (150 mm) of weld length, or 25% of the total weld length, whichever is less . Criterion B imposes no depth limit — the control is length, plus the separate Criterion K requirement that total joint thickness including reinforcement be at least T w T_w T w ​ .

In Severe Cyclic Conditions: Under fatigue cycling, an incomplete penetration notch acts as a fatigue crack starter. Table 341.3.2 assigns Symbol A : zero incomplete penetration is allowed .

3. Undercut (Symbol H vs. Symbol A)

Undercut is a groove melted into the base metal adjacent to the weld toe or root that is left unfilled by weld metal:

In Normal Fluid Service (Criterion H): External and internal undercut is acceptable if the depth does not exceed 1/32 in. (1 mm) and T w / 4 T_w/4 T w ​ /4 (the lesser of the two governs), and the cumulative length of internal and external undercut does not exceed 1.5 in. (38 mm) in any 6 in. (150 mm) of weld, or 25% of the total weld length, whichever is less .

In Category D (Criterion I): The depth limit relaxes to 1/16 in. (1.5 mm) and T w / 4 T_w/4 T w ​ /4 , with the same cumulative-length control.

In Severe Cyclic Conditions: Undercut creates a severe notch at the weld toe, where fatigue stress concentrations are concentrated. Table 341.3.2 mandates Symbol A: ZERO UNDERCUT ALLOWED .

Table 341.3.2 Note L: Weld Reinforcement & Internal Protrusion Limits

Weld reinforcement (the weld metal build-up extending beyond the outer surface of the pipe) and internal root protrusion (weld metal extending beyond the inside pipe surface) are strictly bounded to prevent excessive stress concentrations and internal flow restriction. The limits are identical for external reinforcement and internal protrusion:

Component Nominal Wall Thickness ( T w T_w T w ​ ) Maximum Allowable External Reinforcement & Internal Protrusion

T w < = 1 / 4 in. ( 6 mm ) T_w <= 1/4\text{ in.} (6\text{ mm}) T w ​ <= 1/4 in. ( 6 mm ) 1/16 in. (1.5 mm)

1 / 4 in. < T w < = 1 / 2 in. ( 13 mm ) 1/4\text{ in.} < T_w <= 1/2\text{ in.} (13\text{ mm}) 1/4 in. < T w ​ <= 1/2 in. ( 13 mm ) 1/8 in. (3.0 mm)

1 / 2 in. < T w < = 1 in. ( 25 mm ) 1/2\text{ in.} < T_w <= 1\text{ in.} (25\text{ mm}) 1/2 in. < T w ​ <= 1 in. ( 25 mm ) 5/32 in. (4.0 mm)

T w > 1 in. ( 25 mm ) T_w > 1\text{ in.} (25\text{ mm}) T w ​ > 1 in. ( 25 mm ) 3/16 in. (5.0 mm)

Important

Internal Protrusion vs. External Reinforcement: A common endorsement exam question asks whether internal root protrusion limits differ from external crown reinforcement limits under Table 341.3.2. Note L states that both internal protrusion and external reinforcement are governed by the exact same thickness-based schedule .

Smooth Transition Requirement in Severe Cyclic Conditions

For Severe Cyclic Conditions, Table 341.3.2 enforces a critical qualitative modifier on Note L: weld reinforcement must merge smoothly with the base metal surface without sharp transitions. If necessary, weld crowns must be ground flush or blended smoothly to eliminate stress raisers at the weld toes.

  • Real-World Inspection Scenarios & High-Frequency Exam Traps
  • Scenario 1: The Severe Cyclic Root Incomplete Penetration

A welding inspector is interpreting radiographic film of a 6 in. Schedule 40 (wall thickness 0.280 in.) hydrocarbon reactor feed line operating under Severe Cyclic Conditions . The radiograph reveals a distinct 1.0 in. long straight dark line along the root edge, and the total weld circumference is about 21 in. The welding foreman requests acceptance under Criterion B, reasoning that 1.0 in. is under the 1.5 in. allowance.

The CWI Audit Finding: Two errors. First, in the Severe Cyclic column Table 341.3.2 assigns Criterion A to incomplete penetration — none is permitted — so the indication is rejectable regardless of length. Second, even in Normal Fluid Service the foreman's arithmetic is incomplete: Criterion B is the lesser of 1.5 in. in any 6 in. or 25% of the total weld length , and 25% of a 21 in. circumference is 5.25 in., so here the 1.5 in. figure would govern — but only after checking both values, and with no depth allowance entering the calculation at all.

Scenario 2: The Undercut Evaluation on 1/2-inch Pipe

An inspector evaluates external undercut on a 0.500-inch wall pipe in Normal Fluid Service. The undercut is measured at 0.040 in. deep for a continuous length of 1.0 in.

Maximum allowable depth: the lesser of 1/32 in. (0.0312 in.) or T w / 4 T_w/4 T w ​ /4 ( 0.500 / 4 = 0.125 in. 0.500 / 4 = 0.125\text{ in.} 0.500/4 = 0.125 in. ). The governing limit is 1/32 in. (0.0312 in.) .

The measured depth of 0.040 in. exceeds 0.0312 in. The weld is unacceptable .

Common Exam Traps to Avoid

The Severe Cyclic Undercut Trap: Candidates frequently assume that minor undercut (up to 1/32 in.) is permissible everywhere. Remember: Severe Cyclic Conditions allows ZERO undercut .

The Crack Trap: Forgetting that cracks are strictly prohibited (Symbol A) in all categories, including Category D utility lines.

The Thickness Transition Trap: For pipes of differing wall thicknesses joined together, T w T_w T w ​ is defined as the nominal wall thickness of the thinner of the two components being joined.

The Phantom Depth Limit: Criterion B (and Criterion C) control cumulative length only . If an option attaches "depth <= 1/32 in. or 0.2 T w T_w T w ​ " to incomplete penetration, it is wrong.

The 25% Clause: Criteria B, C, H, and I all carry "...or 25% of total weld length, whichever is less." On short welds the 25% value governs, not the 1.5 in. figure.

Loading diagram... ASME B31.3 Table 341.3.2 Imperfection Acceptance Decision Protocol