Study guide
13.2 B31.3 Inspection vs. Examination Responsibilities & Examination Extents
AWS ASME BPVC Section IX + B31.1/B31.3 Endorsement CWI/SCWI
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Structure, Logistics & Code Navigation Strategy
1.1 Credential Overview, Prometric Delivery & July 2025 Hard-Copy Rule 1.2 The Three-Code Triad: Section IX, B31.1, and B31.3 Roles & Interrelationships 1.3 Rapid Code-Book Navigation: Tabbing, Cross-Referencing & Time Management
2 Chapter 2: Section IX Article I — General Welding Requirements
2.1 Scope, Responsibilities & Section IX Architecture 2.2 Mechanical Test Types, Specimen Dimensions & Acceptance Criteria 2.3 Notch-Toughness Tests, Fillet-Weld Tests & Special Examinations
3 Chapter 3: Section IX Article II — Procedure Qualification Fundamentals
3.1 PQR vs. WPS Workflow, Purpose & Content Requirements 3.2 Coupling and Supporting Multiple WPSs and PQRs 3.3 Test Coupons, Preparation & Required Test Specimen Allocations
4 Chapter 4: Section IX Procedure Qualification Limits & Thickness Rules
4.1 Base Metal & Deposited Weld Metal Thickness Limits 4.2 Impact Testing Requirements & Toughness Thickness Qualification Ranges 4.3 Fillet Weld Procedure Qualification Rules & Special Applications
5 Chapter 5: Section IX Article III — Welder Performance Qualification Fundamentals
5.1 Welder & Welding Operator Qualification Intent, Responsibilities & Identification 5.2 Qualification Testing Methods: Mechanical Bend Tests vs. Volumetric NDE 5.3 Welder Qualification Continuity, Expiration, and Requalification
6 Chapter 6: Section IX Welder Performance Limits, Positions & Diameters
6.1 Test Positions, Groove Weld Orientations & Production Position Limits 6.2 Welder Thickness Limits and Pipe Diameter Qualification Ranges 6.3 Welder Essential Variables: F-Numbers, Backing, and Process Transfers
7 Chapter 7: Section IX Article IV — Welding Variables by Process (Part 1: SMAW & GTAW)
7.1 Understanding Essential, Supplementary Essential & Nonessential Variables 7.2 Shielded Metal Arc Welding (SMAW) Procedure Variables 7.3 Gas Tungsten Arc Welding (GTAW) Procedure Variables
8 Chapter 8: Section IX Article IV — Welding Variables by Process (Part 2: GMAW/FCAW & SAW)
8.1 GMAW & FCAW Procedure Variables and Short-Circuiting Transfer Rules 8.2 Submerged Arc Welding (SAW) Procedure Variables and Flux-Wire Combinations 8.3 Special Variables: Heat Input, Electrical Characteristics & Shielding Gases
9 Chapter 9: Section IX Material Classifications, Numbers & Standard Documentation
9.1 Base Metal P-Numbers, Group Numbers, and S-Numbers 9.2 Filler Metal F-Numbers and As-Deposited Chemistry A-Numbers 9.3 ASME Standard Documentation: Auditing WPS, PQR, and WPQ Forms
10 Chapter 10: ASME B31.1 Power Piping — Scope, Materials, Design & Welding Fabrication
10.1 B31.1 Scope, Jurisdiction, Boiler External Piping vs. Non-Boiler External Piping 10.2 B31.1 Welding Requirements, Joint Alignment, Backing Rings & Tack Welds 10.3 B31.1 Welder & Procedure Qualification Interfacing with Section IX 10.4 B31.1 Materials, Design Conditions & Pressure Design of Components
11 Chapter 11: ASME B31.1 Power Piping — Heat Treatment, Examination, Testing & Fabrication Records
11.1 B31.1 Preheat Rules & Mandatory Temperatures 11.2 B31.1 Postweld Heat Treatment (PWHT) Rules, Temperatures & Holding Times 11.3 B31.1 Mandatory NDE Examination, Acceptance Standards & Pressure Leak Tests 11.4 B31.1 Bending, Forming, Assembly & Code Records
12 Chapter 12: ASME B31.3 Process Piping — Scope, Fluid Services, Materials, Design & Welding
12.1 B31.3 Scope, Fluid Service Classifications & Owner Responsibilities 12.2 B31.3 Welding, Joint Preparation, Backing Rings & Fabrication Details 12.3 B31.3 Procedure & Performance Qualification Rules and Section IX Exceptions 12.4 B31.3 Materials, Design Conditions & Pressure Design of Components
13 Chapter 13: ASME B31.3 Process Piping — Heat Treatment, Examination, Testing, Fabrication & Records
13.1 B31.3 Preheat and Postweld Heat Treatment Rules & Tables 13.2 B31.3 Inspection vs. Examination Responsibilities & Examination Extents 13.3 B31.3 Acceptance Criteria for Weld Imperfections 13.4 B31.3 Pressure Leak Testing: Hydrostatic, Pneumatic & Sensitive Leak Tests 13.5 B31.3 Bending, Forming, Assembly & Records
13.2 B31.3 Inspection vs. Examination Responsibilities & Examination Extents
Key Takeaways Explain This Topic AI
In ASME B31.3, 'Inspection' (Para 340) applies exclusively to functions performed by the Owner's Inspector to verify code compliance, whereas 'Examination' (Para 341) applies to quality control functions performed by the manufacturer, fabricator, or erector.
Para 340.4(b) gives the Owner's Inspector four alternative qualification routes: 10 years of pressure-piping experience, a professional engineering registration with 5 years, AWS CWI or SCWI certification with 5 years, or API 570 authorized piping inspector status with 5 years.
Under Para 342, NDE examiners must be qualified in accordance with the employer's written practice conforming to ASNT SNT-TC-1A, ANSI/ASNT CP-189, or AWS CWI/SCWI for visual examination.
Normal Fluid Service mandates 100% visual examination of completed welds, random 5% visual of fabrication, and random 5% radiographic or ultrasonic examination of circumferential butt welds representing each welder's work.
Severe Cyclic Conditions (Para 341.4.3) requires 100% radiography or ultrasonic examination of circumferential butt and miter groove welds, while Category M (Para M341.4(b)(1)) requires only at least 20% random volumetric examination — four times the 5% Normal Fluid Service rate, but not a 100% regime.
Last updated: September 2026
13.2 B31.3 Inspection vs. Examination Responsibilities & Examination Extents
In ASME B31.3 Process Piping, few concepts are tested more aggressively on the AWS CWI Endorsement examination than the legal, contractual, and technical demarcation between Inspection and Examination . In colloquial workshop parlance, "inspection" and "examination" are often used interchangeably. However, in the strict legal architecture of ASME B31.3 Chapter VI (Inspection, Examination, and Testing) , they represent two completely distinct roles with separate reporting lines, responsibilities, and qualification mandates.
The Critical Distinction: Para 340 vs. Para 341
ASME B31.3 explicitly segregates quality control (first-party verification) from quality assurance (second-party owner verification): +---------------------------------------------------------------------------------------------------+
- | ASME B31.3 QUALITY OVERSIGHT DEMARCATION |
- +---------------------------------------------------------------------------------------------------+
- | PARAGRAPH 340: "INSPECTION" | PARAGRAPH 341: "EXAMINATION" |
- | - Performed by OWNER'S INSPECTOR | - Performed by FABRICATOR / ERECTOR |
- | - Acts on behalf of the Plant Owner | - Quality control internal to the contractor |
- | - Verification & audit of compliance | - Direct execution of NDE (VT, RT, UT, MT, PT) |
- | - Independent of production pressures | - Direct production quality control |
- +---------------------------------------------------------------------------------------------------+
- 1. Inspection (ASME B31.3 Para 340)
Under Para 340.1 , inspection applies strictly to functions performed for the owner by the Owner's Inspector or by individuals designated by the Inspector.
Role: The Owner's Inspector does not physically perform non-destructive examination of every weld; rather, the Inspector verifies that all required examinations, welder performance qualifications, welding procedure specifications (WPS), material test reports (MTRs), and pressure tests have been executed in strict accordance with B31.3 and the engineering design.
Inspector Qualifications (Para 340.4(b)): The Owner's Inspector shall meet one of four alternative routes:
At least 10 years of experience in the design, fabrication, or examination of industrial pressure piping. Each 20% of satisfactorily completed work toward an accredited engineering degree counts as 1 year of experience, up to 5 years total .
A professional engineering registration or nationally recognized equivalent with at least 5 years of experience in the design, fabrication, or examination of industrial pressure piping.
Certification as a certified welding inspector or senior certified welding inspector as defined in AWS QC1 , or a nationally recognized equivalent, with at least 5 years of that experience.
Status as an authorized piping inspector as defined in API 570 with at least 5 years of that experience.
Independence (Para 340.4(a)): The Owner's Inspector shall be designated by the owner and shall be the owner, an employee of the owner, an employee of an engineering or scientific organization, or an employee of a recognized insurance or inspection company acting as the owner's agent. The Inspector shall not represent nor be an employee of the piping manufacturer, fabricator, or erector unless the owner is also that party.
- Important
- The CWI route requires 5 years, not 3. Para 340.4(b)(3) sets the same 5-year experience bar for a CWI or SCWI
that route (2) sets for a registered professional engineer. Only route (1) — the general experience route with no
credential — carries the 10-year requirement.
2. Examination (ASME B31.3 Para 341)
Under Para 341.1 , examination applies strictly to quality control functions performed by personnel employed by, or under contract to, the manufacturer, fabricator, or erector.
Role: Examiners perform the hands-on visual examinations, film interpretations, ultrasonic calibrations, magnetic particle checks, and liquid penetrant evaluations required by the code and project specifications.
Examiner Qualifications (Para 342): Personnel performing non-destructive examinations must be qualified and certified in accordance with the employer's written practice, conforming to:
ASNT SNT-TC-1A ( Recommended Practice for Nondestructive Testing Personnel Qualification and Certification ), or
ANSI/ASNT CP-189 ( Standard for Qualification and Certification of Nondestructive Testing Personnel ), or
AWS CWI / SCWI for visual examination (VT).
Vision requirements: Annual near-vision acuity examination (Jaeger J-1 or J-2 equivalent at 12 inches) and color contrast discrimination.
Extent of Required Examination by Fluid Service (Para 341.4)
ASME B31.3 does not apply a blanket examination percentage across all piping systems. Instead, the required percentage of visual and volumetric examination is directly governed by the Fluid Service Classification designated by the owner:
Fluid Service Classification Visual Examination (VT) Extent Volumetric Examination (RT or UT) Extent Surface Examination (MT or PT) Extent
Category D (Para 341.4.2) In-process fit-up and completed weld exterior 0% (None required by code) None required by code
Normal Fluid Service (Para 341.4.1) 100% materials & completed welds; >= 5% in-process 5% Random circumferential butt & miter welds None required (unless specified)
Category M (Chapter VIII Para M341.4) 100% of fabrication and all threaded, bolted, and mechanical joints >= 20% Random circumferential butt and miter welds, plus fabricated lap and branch connection welds Sensitive leak test (Para M345 / 345.8)
Severe Cyclic Conditions (Para 341.4.3) 100% all materials, fit-up, and completed welds 100% Mandatory circumferential butt & miter welds 100% Mandatory socket & branch connection welds
High Pressure (Chapter IX Para K341.4) 100% all fabrication steps 100% Mandatory all butt welds 100% Mandatory all branch / fillet welds
In-Depth Breakdown of Normal Fluid Service (Para 341.4.1)
For standard process piping in Normal Fluid Service, B31.3 mandates:
Visual Examination:
At least 5% random in-process examination of joint preparation, alignment, cleaning, preheating, and tack welding.
100% visual examination of completed external weld surfaces, piping components, and assembled spring supports and hangers.
Random Volumetric Examination:
At least 5% random radiographic (RT) or ultrasonic (UT) examination of circumferential butt and miter groove welds.
The Welder Lot Rule: The 5% sample must be selected so that it represents the work of each welder and welding operator performing production welding on that project lot. Inspecting 5% of welds from one skilled welder does not fulfill the requirement for other welders working on the same system.
In-line branch connections (such as weldolets or fabricated tees) must have at least 5% examined if volumetric examination is feasible.
Category M Fluid Service (Para M341.4)
Chapter VIII applies Para 341.4.1 to Category M piping with exceptions that raise the random sampling rate , not exceptions that make it a blanket 100% regime:
All fabrication shall be examined, and all threaded, bolted, and other mechanical joints shall be examined.
The radiography and ultrasonic requirements of Para 341.4.1(b)(1) apply except that at least 20% of circumferential butt and miter welds, and of the fabricated lap and branch connection welds comparable to those shown in Figures 328.5.4E and 328.5.5 sketches (d) and (e), shall be examined. The 20% is applied to the aggregate of those weld categories — no weld type inside a Category M system stays at the 5% rate.
Para M345 further requires a sensitive leak test per Para 345.8 as part of the required leak test, and the initial service leak test of Para 345.7 does not apply to Category M.
Severe Cyclic Conditions (Para 341.4.3)
Because Severe Cyclic Conditions involves fatigue loading, microscopic stress concentrations can propagate into fatigue cracks. The code enforces an uncompromising inspection standard:
100% Visual Examination: Every linear millimeter of every weld.
100% Volumetric Examination: Every circumferential butt and miter groove weld must be 100% radiographed or ultrasonically examined.
100% Surface Examination: Branch connections and socket welds that cannot be examined by RT or UT must be 100% examined by magnetic particle (MT) or liquid penetrant (PT).
Progressive Examination Protocol (Para 341.3.4)
When non-destructive examination is performed on a random sample basis (such as the 5% required for Normal Fluid Service), a critical question arises: What happens when a rejectable defect is discovered in the sample?
ASME B31.3 Para 341.3.4 establishes the Progressive Examination rule—a rigorous statistical escalation protocol designed to ensure that systemic welding defects do not remain concealed within the unexamined portion of a production lot: INITIAL DEFECT DISCOVERED
- (In the 5% Normal Fluid Service Sample)
- |
- v
- REPAIR ORIGINAL DEFECT
- &
- EXAMINE 2 ADDITIONAL ITEMS FROM SAME LOT
- |
- +--------------------+--------------------+
- | |
- v v
- BOTH ITEMS PASS EITHER ITEM FAILS
- | |
- v v
- LOT ACCEPTED SECOND DEFECT CONFIRMED
- (Repaired weld re-examined) |
- v
- EXAMINE 2 FURTHER ITEMS FOR EACH
- DEFECTIVE ITEM IN 2ND EXPANSION
- |
- +---------------------+---------------------+
- | |
- v v
- ALL ITEMS PASS ANY ITEM FAILS
- | |
- v v
- LOT ACCEPTED 100% LOT EXAMINATION
- (Repairs re-examined) OR
- ENTIRE LOT REJECTED
- Progressive Examination Step-by-Step Escalation
Step 1: Original Defect Discovery & Repair:
When an item examined in a random sample reveals a defect exceeding Table 341.3.2 acceptance criteria, the defective weld must be repaired or replaced and re-examined until acceptable.
Step 2: First Expansion (Two Additional Items):
Two additional items of the same kind from the same lot (typically welds produced by the same welder/operator in that piping spool run) must be examined by the same examination method.
Outcome A: If both additional items are acceptable, the lot is accepted (provided the original repaired weld passes re-examination).
Step 3: Second Expansion (Cascading Escalation):
Outcome B: If either of the two additional items examined reveals a defect, two further additional items must be examined for each defective item found in this second round.
For example, if one of the two additional items failed, 1 × 2 = 2 1 \times 2 = 2 1 × 2 = 2 more items must be examined. If both failed, 2 × 2 = 4 2 \times 2 = 4 2 × 2 = 4 more items must be examined.
Step 4: Total Lot Rejection or 100% Examination:
If any of the items examined in the second expansion reveal a defect, the entire lot has demonstrated a systemic failure rate. Under Para 341.3.4(c), the contractor faces two choices:
Examine 100% of all remaining items in that lot, repairing every defective weld found; OR
Completely reject the lot , cutting out and re-welding all joints in the production batch.
- Practical Field Scenarios & High-Frequency Exam Traps
- Scenario: The Welder Representation Oversight
A mechanical piping contractor fabricates a 50-joint piping header under Normal Fluid Service. Five welders (A, B, C, D, and E) each deposit 10 butt welds. The quality manager selects 3 butt welds (5% of 50 is 2.5, rounded up to 3) for RT, all produced by Welder A, who is known to be the most experienced craftsman on the crew. All 3 radiographs pass. The contractor submits the package for hydrotesting.
The CWI Audit Finding: The Owner's Inspector rejects the examination submittal. Under Para 341.4.1(b)(1) , random volumetric examination must be selected to represent the work of each welder and welding operator . Welder A's welds cannot satisfy the examination quota for Welders B, C, D, and E. The contractor must shoot at least one random weld from each welder, requiring a minimum of 5 total radiographic exposures across the lot.
Common Exam Traps to Avoid
The Inspector vs. Examiner Trap: An exam question may ask: "Who is responsible for visual examination of completed welds under ASME B31.3?" The answer is the Examiner (employed by the fabricator/erector). The Owner's Inspector verifies that examinations have been performed.
The Progressive Examination Math Trap: When a weld fails, how many additional welds are shot? The answer is two (2) additional samples of the same kind , and for a welded joint they must be by the same welder, bonder, or operator from the original designated lot. If one of those two fails, two further samples are examined for each defective item found by that sampling. Do not answer "5 welds" or "10% of the lot."
The Category M Percentage Trap: Category M raises random volumetric examination from the 5% of Normal Fluid Service to at least 20% under Para M341.4(b)(1) — it is not a blanket 100% volumetric regime. Reserve "100% of circumferential butt and miter welds" for Severe Cyclic Conditions (Para 341.4.3). Confusing the two is the single most common Chapter VIII error.
Severe Cyclic Examination Method Trap: Believing that 100% RT/UT is required on socket welds in Severe Cyclic piping. RT and UT cannot reliably inspect fillet and socket weld geometries; B31.3 Para 341.4.3 specifically mandates 100% MT or PT on socket and branch welds.