Study guide
4.1 Base Metal & Deposited Weld Metal Thickness Limits
AWS ASME BPVC Section IX + B31.1/B31.3 Endorsement CWI/SCWI
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Structure, Logistics & Code Navigation Strategy
1.1 Credential Overview, Prometric Delivery & July 2025 Hard-Copy Rule 1.2 The Three-Code Triad: Section IX, B31.1, and B31.3 Roles & Interrelationships 1.3 Rapid Code-Book Navigation: Tabbing, Cross-Referencing & Time Management
2 Chapter 2: Section IX Article I — General Welding Requirements
2.1 Scope, Responsibilities & Section IX Architecture 2.2 Mechanical Test Types, Specimen Dimensions & Acceptance Criteria 2.3 Notch-Toughness Tests, Fillet-Weld Tests & Special Examinations
3 Chapter 3: Section IX Article II — Procedure Qualification Fundamentals
3.1 PQR vs. WPS Workflow, Purpose & Content Requirements 3.2 Coupling and Supporting Multiple WPSs and PQRs 3.3 Test Coupons, Preparation & Required Test Specimen Allocations
4 Chapter 4: Section IX Procedure Qualification Limits & Thickness Rules
4.1 Base Metal & Deposited Weld Metal Thickness Limits 4.2 Impact Testing Requirements & Toughness Thickness Qualification Ranges 4.3 Fillet Weld Procedure Qualification Rules & Special Applications
5 Chapter 5: Section IX Article III — Welder Performance Qualification Fundamentals
5.1 Welder & Welding Operator Qualification Intent, Responsibilities & Identification 5.2 Qualification Testing Methods: Mechanical Bend Tests vs. Volumetric NDE 5.3 Welder Qualification Continuity, Expiration, and Requalification
6 Chapter 6: Section IX Welder Performance Limits, Positions & Diameters
6.1 Test Positions, Groove Weld Orientations & Production Position Limits 6.2 Welder Thickness Limits and Pipe Diameter Qualification Ranges 6.3 Welder Essential Variables: F-Numbers, Backing, and Process Transfers
7 Chapter 7: Section IX Article IV — Welding Variables by Process (Part 1: SMAW & GTAW)
7.1 Understanding Essential, Supplementary Essential & Nonessential Variables 7.2 Shielded Metal Arc Welding (SMAW) Procedure Variables 7.3 Gas Tungsten Arc Welding (GTAW) Procedure Variables
8 Chapter 8: Section IX Article IV — Welding Variables by Process (Part 2: GMAW/FCAW & SAW)
8.1 GMAW & FCAW Procedure Variables and Short-Circuiting Transfer Rules 8.2 Submerged Arc Welding (SAW) Procedure Variables and Flux-Wire Combinations 8.3 Special Variables: Heat Input, Electrical Characteristics & Shielding Gases
9 Chapter 9: Section IX Material Classifications, Numbers & Standard Documentation
9.1 Base Metal P-Numbers, Group Numbers, and S-Numbers 9.2 Filler Metal F-Numbers and As-Deposited Chemistry A-Numbers 9.3 ASME Standard Documentation: Auditing WPS, PQR, and WPQ Forms
10 Chapter 10: ASME B31.1 Power Piping — Scope, Materials, Design & Welding Fabrication
10.1 B31.1 Scope, Jurisdiction, Boiler External Piping vs. Non-Boiler External Piping 10.2 B31.1 Welding Requirements, Joint Alignment, Backing Rings & Tack Welds 10.3 B31.1 Welder & Procedure Qualification Interfacing with Section IX 10.4 B31.1 Materials, Design Conditions & Pressure Design of Components
11 Chapter 11: ASME B31.1 Power Piping — Heat Treatment, Examination, Testing & Fabrication Records
11.1 B31.1 Preheat Rules & Mandatory Temperatures 11.2 B31.1 Postweld Heat Treatment (PWHT) Rules, Temperatures & Holding Times 11.3 B31.1 Mandatory NDE Examination, Acceptance Standards & Pressure Leak Tests 11.4 B31.1 Bending, Forming, Assembly & Code Records
12 Chapter 12: ASME B31.3 Process Piping — Scope, Fluid Services, Materials, Design & Welding
12.1 B31.3 Scope, Fluid Service Classifications & Owner Responsibilities 12.2 B31.3 Welding, Joint Preparation, Backing Rings & Fabrication Details 12.3 B31.3 Procedure & Performance Qualification Rules and Section IX Exceptions 12.4 B31.3 Materials, Design Conditions & Pressure Design of Components
13 Chapter 13: ASME B31.3 Process Piping — Heat Treatment, Examination, Testing, Fabrication & Records
13.1 B31.3 Preheat and Postweld Heat Treatment Rules & Tables 13.2 B31.3 Inspection vs. Examination Responsibilities & Examination Extents 13.3 B31.3 Acceptance Criteria for Weld Imperfections 13.4 B31.3 Pressure Leak Testing: Hydrostatic, Pneumatic & Sensitive Leak Tests 13.5 B31.3 Bending, Forming, Assembly & Records
4.1 Base Metal & Deposited Weld Metal Thickness Limits
Key Takeaways Explain This Topic AI
Under ASME Section IX Table QW-451.1, test coupon thickness T governs base metal qualification: T < 1/16 in. qualifies T to 2T; 1/16 in. to 3/8 in. qualifies 1/16 in. to 2T; 3/8 in. to < 1-1/2 in. qualifies 3/16 in. to 2T; and T >= 1-1/2 in. qualifies 3/16 in. to 8 in. (200 mm).
Deposited weld metal thickness t qualifies a maximum of 2t per process, except that when t is 3/4 in. (19 mm) or greater the maximum qualified deposit becomes 8 in. (200 mm) under Table QW-451.1 for SMAW, SAW, GMAW, GTAW, PAW, and LLBW.
Short-circuiting GMAW carries two distinct limits: QW-403.10 caps qualified base metal thickness at 1.1T when the coupon thickness T is under 1/2 in. (13 mm), and QW-404.32 caps qualified deposited weld metal at 1.1t when the deposit t is under 1/2 in. (13 mm).
The three-layer rule belongs to welder performance qualification, not procedure qualification: Table QW-452.1(b) grants unlimited production thickness only when the welder deposits 1/2 in. (13 mm) or more in a minimum of three layers.
Table QW-451.2 governs longitudinal guided-bend testing, which replaces transverse bend tests when base metal and weld metal exhibit substantially different mechanical properties (e.g., dissimilar metal joints or certain aluminum alloys).
Last updated: September 2026
4.1 Base Metal & Deposited Weld Metal Thickness Limits
Core Principle: In ASME Section IX procedure qualification, thickness rules are governed by two distinct dimensions: coupon base metal thickness ( T T T ) and individual deposited weld metal thickness ( t t t ). A single test coupon establishes a certified envelope that dictates both the permissible base metal thicknesses a fabricator may weld in production and the maximum thickness of weld deposit permitted for each welding process or filler metal.
1. The Geometry of Procedure Qualification: Base Metal ( T T T ) vs. Deposited Metal ( t t t )
A primary source of confusion on the AWS CWI ASME Endorsement examination is the fundamental distinction between base metal thickness and weld metal thickness:
Test Coupon Base Metal Thickness ( T T T ): The nominal thickness of the plate or pipe base material joined during the procedure qualification test. T T T governs the qualified base metal thickness range ( T min T_{\text{min}} T min to T max T_{\text{max}} T max ) that may be welded in production under the resulting Welding Procedure Specification (WPS).
Deposited Weld Metal Thickness ( t t t ): The thickness of weld metal deposited by a specific welding process, electrode classification, or filler metal heat/lot within the groove. In single-process welds with complete penetration, t t t is typically equal to T T T . In multi-process welds (e.g., GTAW root followed by SMAW fill and cap), each process deposits a fraction of the total groove thickness ( t 1 + t 2 = T t_1 + t_2 = T t 1 + t 2 = T ). Each process's deposited thickness t t t governs its own maximum qualified deposited weld metal thickness ( t max t_{\text{max}} t max ). +-----------------------------------------------------------------------------------------+
- | NOMENCLATURE & GEOMETRY IN ARTICLE IV |
- +-----------------------------------------------------------------------------------------+
- | SYMBOL | DEFINITION | GOVERNING CODE IMPACT |
- +----------+----------------------------------------+---------------------------------------------+
- | T | Nominal thickness of coupon base metal | Dictates base metal range (QW-451.1) |
- | t | Deposited thickness of weld metal | Dictates max weld deposit per process |
- | T_prod | Production base metal thickness | Must fall within: T_min <= T_prod <= T_max |
- | t_prod | Production weld deposit thickness | Must not exceed t_max for that process |
- +-----------------------------------------------------------------------------------------+
- 2. Table QW-451.1: Groove-Weld Thickness Limits & Specimen Allocations
Table QW-451.1 is the definitive reference table for groove weld procedure qualification using transverse tension and bend specimens. Inspectors and welding engineers must commit its key thresholds to memory.
Coupon Thickness T T T Range of Base Metal Qualified ( T T T ) Maximum Deposited Weld Metal Qualified ( t t t ) Mandatory Test Specimens
T < 1 / 16 in. T < 1/16\text{ in.} T < 1/16 in. ( 1.5 mm 1.5\text{ mm} 1.5 mm ) T T T min to 2 T 2T 2 T max 2 t 2t 2 t max 2 Tension, 2 Face Bend, 2 Root Bend
1 / 16 to 3 / 8 in. 1/16\text{ to } 3/8\text{ in.} 1/16 to 3/8 in. ( 1.5 to 10 mm 1.5\text{ to } 10\text{ mm} 1.5 to 10 mm ) 1 / 16 in. 1/16\text{ in.} 1/16 in. ( 1.5 mm 1.5\text{ mm} 1.5 mm ) min to 2 T 2T 2 T max 2 t 2t 2 t max 2 Tension, 2 Face Bend, 2 Root Bend
3 / 8 to < 3 / 4 in. 3/8\text{ to } < 3/4\text{ in.} 3/8 to < 3/4 in. ( 10 to < 19 mm 10\text{ to } < 19\text{ mm} 10 to < 19 mm ) 3 / 16 in. 3/16\text{ in.} 3/16 in. ( 5 mm 5\text{ mm} 5 mm ) min to 2 T 2T 2 T max 2 t 2t 2 t max 2 Tension, 4 Side Bend (or 2 Face + 2 Root)
3 / 4 to < 1 - 1 / 2 in. 3/4\text{ to } < 1\text{-}1/2\text{ in.} 3/4 to < 1 - 1/2 in. ( 19 to < 38 mm 19\text{ to } < 38\text{ mm} 19 to < 38 mm ) 3 / 16 in. 3/16\text{ in.} 3/16 in. ( 5 mm 5\text{ mm} 5 mm ) min to 2 T 2T 2 T max 2 t 2t 2 t when t < 3 / 4 in. t < 3/4\text{ in.} t < 3/4 in. ; 8 in. 8\text{ in.} 8 in. when t ≥ 3 / 4 in. t \ge 3/4\text{ in.} t ≥ 3/4 in. 2 Tension, 4 Side Bend
T ≥ 1 - 1 / 2 in. T \ge 1\text{-}1/2\text{ in.} T ≥ 1 - 1/2 in. ( T ≥ 38 mm T \ge 38\text{ mm} T ≥ 38 mm ) 3 / 16 in. 3/16\text{ in.} 3/16 in. ( 5 mm 5\text{ mm} 5 mm ) min to 8 in. 8\text{ in.} 8 in. ( 200 mm 200\text{ mm} 200 mm ) max 2 t 2t 2 t when t < 3 / 4 in. t < 3/4\text{ in.} t < 3/4 in. ; 8 in. 8\text{ in.} 8 in. when t ≥ 3 / 4 in. t \ge 3/4\text{ in.} t ≥ 3/4 in. 2 Tension, 4 Side Bend
Detailed Analysis of Coupon Brackets
Sheet Material ( T < 1 / 16 in. T < 1/16\text{ in.} T < 1/16 in. / 1.5 mm 1.5\text{ mm} 1.5 mm ):
Minimum base metal qualified is equal to the coupon thickness T T T .
Maximum base metal qualified is 2 T 2T 2 T .
Example: A coupon welded at 0.040 in. 0.040\text{ in.} 0.040 in. qualifies base metal from 0.040 in. 0.040\text{ in.} 0.040 in. to 0.080 in. 0.080\text{ in.} 0.080 in. It does not qualify down to zero.
Standard Thin Plate/Pipe ( 1 / 16 in. ≤ T ≤ 3 / 8 in. 1/16\text{ in.} \le T \le 3/8\text{ in.} 1/16 in. ≤ T ≤ 3/8 in. / 1.5 mm to 10 mm 1.5\text{ mm to } 10\text{ mm} 1.5 mm to 10 mm ):
Minimum base metal qualified is fixed at 1 / 16 in. 1/16\text{ in.} 1/16 in. ( 1.5 mm 1.5\text{ mm} 1.5 mm ), regardless of whether T T T is 1 / 8 in. 1/8\text{ in.} 1/8 in. or 3 / 8 in. 3/8\text{ in.} 3/8 in.
Maximum base metal qualified is 2 T 2T 2 T .
Example: A coupon welded at 3 / 8 in. 3/8\text{ in.} 3/8 in. ( 0.375 in. 0.375\text{ in.} 0.375 in. ) qualifies base metal from 1 / 16 in. 1/16\text{ in.} 1/16 in. ( 0.0625 in. 0.0625\text{ in.} 0.0625 in. ) up to 3 / 4 in. 3/4\text{ in.} 3/4 in. ( 0.750 in. 0.750\text{ in.} 0.750 in. ).
Intermediate Plate/Pipe ( 3 / 8 in. < T < 1 - 1 / 2 in. 3/8\text{ in.} < T < 1\text{-}1/2\text{ in.} 3/8 in. < T < 1 - 1/2 in. / 10 mm to 38 mm 10\text{ mm to } 38\text{ mm} 10 mm to 38 mm ):
Minimum base metal qualified shifts to 3 / 16 in. 3/16\text{ in.} 3/16 in. ( 5 mm 5\text{ mm} 5 mm ).
Maximum base metal qualified remains 2 T 2T 2 T .
Example: A coupon welded at 1.0 in. 1.0\text{ in.} 1.0 in. qualifies base metal from 3 / 16 in. 3/16\text{ in.} 3/16 in. ( 0.1875 in. 0.1875\text{ in.} 0.1875 in. ) up to 2.0 in. 2.0\text{ in.} 2.0 in. ( 50 mm 50\text{ mm} 50 mm ).
Heavy Wall / Plate ( T ≥ 1 - 1 / 2 in. T \ge 1\text{-}1/2\text{ in.} T ≥ 1 - 1/2 in. / 38 mm 38\text{ mm} 38 mm ):
Minimum base metal qualified is 3 / 16 in. 3/16\text{ in.} 3/16 in. ( 5 mm 5\text{ mm} 5 mm ).
Maximum base metal qualified is capped at 8 in. 8\text{ in.} 8 in. ( 200 mm 200\text{ mm} 200 mm ) , rather than 2 T 2T 2 T .
Special Rule for Ultra-Heavy Coupons ( T > 8 in. T > 8\text{ in.} T > 8 in. ): If a test coupon is welded on material thicker than 8 in. 8\text{ in.} 8 in. , the maximum qualified base metal thickness is 1.33 T 1.33T 1.33 T (or 2 T 2T 2 T depending on specific code edition notes for fracture-critical construction).
3. Deposited Weld Metal Thickness ( t t t ) Rules & the 8-Inch Heavy-Deposit Rule
In addition to qualifying the base metal thickness range, the PQR must validate the thickness of weld metal deposited ( t t t ). Under Table QW-451.1:
General Rule: For any process, the maximum qualified deposited weld metal thickness is 2 t 2t 2 t , where t t t is the thickness of weld metal deposited by that process on the test coupon.
The Heavy-Deposit Rule: When the deposited thickness t t t is 3 / 4 in. 3/4\text{ in.} 3/4 in. ( 19 mm 19\text{ mm} 19 mm ) or greater , the maximum qualified deposited weld metal thickness becomes 8 in. 8\text{ in.} 8 in. ( 200 mm 200\text{ mm} 200 mm ) instead of 2 t 2t 2 t . The Table QW-451.1 note limits this allowance to SMAW, SAW, GMAW, GTAW, PAW, and LLBW; for every other process the 2 T 2T 2 T and 2 t 2t 2 t values apply as applicable.
No Layer Count Applies Here: Procedure qualification does not impose a minimum number of weld layers as a condition of the 8 in. allowance. The threshold is purely the deposited thickness t t t . +-----------------------------------------------------------------------------------------+
- | THE 8-INCH DEPOSIT RULE (TABLE QW-451.1) IN PRACTICE |
- +-----------------------------------------------------------------------------------------+
- | CASE A: t = 0.50 in. deposited by SMAW |
- | - t < 0.75 in., so the general rule governs. |
- | - Max qualified weld deposit = 2 * t = 2 * 0.50 in. = 1.00 in. |
- |-----------------------------------------------------------------------------------------|
- | CASE B: t = 0.75 in. deposited by SAW in TWO passes |
- | - t >= 0.75 in. and SAW is a listed process. Layer count is irrelevant. |
- | - Max qualified weld deposit = 8.0 in. (200 mm). |
- |-----------------------------------------------------------------------------------------|
- | CASE C: t = 1.00 in. deposited by a process NOT listed in the note |
- | - The 8 in. allowance does not apply; 2t governs. |
- | - Max qualified weld deposit = 2.00 in. |
- +-----------------------------------------------------------------------------------------+
Warning
Do not import the three-layer rule into Article II. The "minimum of three layers" condition is a performance qualification rule from Table QW-452.1(b): a welder who deposits 1 / 2 in. 1/2\text{ in.} 1/2 in. ( 13 mm 13\text{ mm} 13 mm )
or more of weld metal in a minimum of three layers qualifies for the maximum thickness to be welded. It has a
different threshold ( 1 / 2 in. 1/2\text{ in.} 1/2 in. , not 3 / 4 in. 3/4\text{ in.} 3/4 in. ), a different subject (the welder, not the procedure),
and a different outcome (unlimited, not 8 in.). Endorsement items deliberately mix the two.
Why Heavy Deposits Get a Wider Range
A coupon that has already demonstrated sound tension and side-bend results through 3 / 4 in. 3/4\text{ in.} 3/4 in. or more of
deposited weld metal has exercised the thermal cycling, interpass conditions, and restraint that thicker production
deposits will see. Section IX therefore treats it as representative of essentially any production deposit up to the
8 in. ceiling, rather than forcing a new PQR for every increase in weld volume.
4. The Critical Short-Circuiting GMAW (GMAW-S) Exception: Paragraph QW-404.32
One of the most heavily tested provisions on the CWI Endorsement exam is the special essential variable for Gas Metal Arc Welding in the Short-Circuiting Transfer Mode (GMAW-S) .
Physics of Short-Circuiting Transfer
In short-circuiting transfer (also known as dip transfer or short-arc), the electrode wire contacts the weld pool directly at a rate of 20 to 200 times per second, extinguishing the arc during each short circuit. This mode operates at low arc voltages (14–22 V) and low currents (50–200 A), resulting in very low heat input. While ideal for thin sheet metal and open-root piping passes, GMAW-S is notoriously prone to lack of sidewall fusion ("cold lap") when applied to thick, heat-sinking base metals.
Two Separate Rules: QW-403.10 and QW-404.32
Section IX addresses GMAW-S with two distinct essential variables , and endorsement items trade on the difference.
One limits base metal; the other limits weld deposit. Neither one limits both.
Paragraph Variable Limited Trigger Qualified Maximum
QW-403.10 Base metal thickness T T T Coupon thickness T T T less than 1 / 2 in. 1/2\text{ in.} 1/2 in. ( 13 mm 13\text{ mm} 13 mm ) 1.1 T 1.1T 1.1 T (not 2 T 2T 2 T )
QW-404.32 Deposited weld metal thickness t t t Deposit t t t less than 1 / 2 in. 1/2\text{ in.} 1/2 in. ( 13 mm 13\text{ mm} 13 mm ) 1.1 t 1.1t 1.1 t (not 2 t 2t 2 t )
When the coupon thickness reaches 1 / 2 in. 1/2\text{ in.} 1/2 in. ( 13 mm 13\text{ mm} 13 mm ) or more, QW-403.10 stops applying and the base
metal range reverts to Table QW-451.1. When the deposit reaches 1 / 2 in. 1/2\text{ in.} 1/2 in. or more, QW-404.32 stops applying and
the deposit range reverts to Table QW-451.1. +-----------------------------------------------------------------------------------------+
- | COMPARISON: STANDARD PROCESS vs. SHORT-CIRCUIT GMAW (GMAW-S) |
- +-----------------------------------------------------------------------------------------+
- | PARAMETER | STANDARD PROCESS (SMAW/GTAW/SAW) | GMAW SHORT-CIRCUITING (GMAW-S) |
- +------------------------+-----------------------------------+------------------------------------+
- | Coupon T = 3/8" (0.375")| Base metal: 1/16" to 2T = 0.750" | Base metal: 1/16" to 1.1T = 0.4125"|
- | single process, t = T | Deposit: max 2t = 0.750" | Deposit: max 1.1t = 0.4125" |
- | | - Governing: Table QW-451.1 | - Governing: QW-403.10 + QW-404.32|
- |------------------------+-----------------------------------+------------------------------------|
- | Coupon T = 1/2" (0.500")| Base metal: 3/16" to 2T = 1.000" | Base metal: 3/16" to 2T = 1.000" |
- | single process, t = T | Deposit: max 2t = 1.000" | Deposit: max 2t = 1.000" |
- | | - Governing: Table QW-451.1 | - Governing: Table QW-451.1 |
- +-----------------------------------------------------------------------------------------+
EXAM ALERT: Read the noun in the stem. If the item asks for the maximum base metal thickness qualified by a 3 / 8 in. 3/8\text{ in.} 3/8 in. short-circuiting GMAW coupon, cite QW-403.10 and answer 0.4125 in. 0.4125\text{ in.} 0.4125 in. ( 1.1 × 0.375 1.1 \times 0.375 1.1 × 0.375 ). If it asks for the maximum deposited weld metal thickness for a GMAW-S deposit of 0.375 in. 0.375\text{ in.} 0.375 in. , cite QW-404.32 and answer the same 0.4125 in. 0.4125\text{ in.} 0.4125 in. — but for a different reason. A
distractor that attributes the base-metal cap to QW-404.32 is a classic wrong answer. If the question states "spray
transfer" or "globular transfer," both special rules disappear and Table QW-451.1 governs ( 0.750 in. 0.750\text{ in.} 0.750 in. ).
The Related Thick-Pass Rule: QW-403.9
A third 1.1 multiplier exists and is often confused with the two above. QW-403.9 applies to any process: when a
procedure qualification coupon is welded with a single pass greater than 1 / 2 in. 1/2\text{ in.} 1/2 in. ( 13 mm 13\text{ mm} 13 mm ) thick, the
maximum qualified base metal thickness is 1.1 T 1.1T 1.1 T . Three paragraphs, three triggers — memorize which noun each one
controls.
5. Table QW-451.2: Longitudinal Guided-Bend Test Rules
Under standard procedure qualification, Table QW-451.1 requires transverse bend specimens (where the weld axis is perpendicular to the specimen length). However, transverse bending relies on the assumption that the base metal and weld metal have comparable yield strengths and tensile ductility.
When Longitudinal Bends Are Mandated (QW-161.5 & QW-451.2)
When the mechanical properties of the base metal and weld metal differ significantly, transverse bend specimens produce severe stress concentrations: the softer metal yields prematurely, stretches beyond its ductility limit, and tears, while the harder metal barely bends. In these situations, Table QW-451.2 permits or mandates longitudinal guided-bend specimens (where the weld axis runs parallel to the specimen length, ensuring base metal and weld metal bend simultaneously at the same radius).
Common metallurgical applications include:
Dissimilar Metal Welds: Joining austenitic stainless steel (P-No. 8) to ferritic carbon steel (P-No. 1) using nickel-alloy filler metal (F-No. 43).
High-Strength Aluminum Alloys: Welded joints in heat-treatable aluminum alloys (e.g., 6061-T6 welded with 4043 filler metal), where the heat-affected zone (HAZ) is drastically overaged and softened.
High-Hardness Weld Overlays & Specialty Alloys: Applications where weld metal yield strength exceeds base metal yield strength by more than 20%.
Specimen Allocation under Table QW-451.2
Tension Specimens: 2 transverse or longitudinal tension specimens.
Bend Specimens: 4 longitudinal bend specimens (2 longitudinal face bends + 2 longitudinal root bends for T < 3 / 8 in. T < 3/8\text{ in.} T < 3/8 in. ; or 4 longitudinal side/face/root bends per Table QW-451.2 notes).
Thickness Range Qualified: The base metal ( T T T ) and deposited weld metal ( t t t ) qualification ranges derived from Table QW-451.2 are identical to those in Table QW-451.1.
- 6. Worked Step-by-Step Mathematical Calculation Scenarios
- Scenario 1: Single-Process SMAW on Intermediate Plate
PQR Coupon: Fabricated from ASTM A516 Gr. 70 plate ( T = 0.625 in. T = 0.625\text{ in.} T = 0.625 in. / 5 / 8 in. 5/8\text{ in.} 5/8 in. ). Welded with multi-pass SMAW using AWS E7018 ( t = 0.625 in. t = 0.625\text{ in.} t = 0.625 in. ). Tension and side-bend tests pass.
Base Metal Range ( T T T ): Because 3 / 8 in. < T < 3 / 4 in. 3/8\text{ in.} < T < 3/4\text{ in.} 3/8 in. < T < 3/4 in. , Table QW-451.1 applies: Min T = 3 / 16 in. = 0.1875 in. ( 5 mm ) \text{Min } T = 3/16\text{ in.} = 0.1875\text{ in.} (5\text{ mm}) Min T = 3/16 in. = 0.1875 in. ( 5 mm ) Max T = 2 T = 2 × 0.625 in. = 1.250 in. ( 32 mm ) \text{Max } T = 2T = 2 \times 0.625\text{ in.} = 1.250\text{ in.} (32\text{ mm}) Max T = 2 T = 2 × 0.625 in. = 1.250 in. ( 32 mm )
Deposited Weld Metal ( t t t ): Single process with t = 0.625 in. t = 0.625\text{ in.} t = 0.625 in. (which is < 0.75 in. < 0.75\text{ in.} < 0.75 in. , so Note 1 does not apply): Max t = 2 t = 2 × 0.625 in. = 1.250 in. ( 32 mm ) \text{Max } t = 2t = 2 \times 0.625\text{ in.} = 1.250\text{ in.} (32\text{ mm}) Max t = 2 t = 2 × 0.625 in. = 1.250 in. ( 32 mm )
Production WPS Authorization: The fabricator can weld production joints between 0.1875 in. 0.1875\text{ in.} 0.1875 in. and 1.250 in. 1.250\text{ in.} 1.250 in. nominal thickness, depositing up to 1.250 in. 1.250\text{ in.} 1.250 in. of E7018 weld metal.
Scenario 2: Multi-Process Combination Joint (GTAW Root + SMAW Fill)
PQR Coupon: Heavy-wall piping butt weld coupon with outer diameter 8.625 in. 8.625\text{ in.} 8.625 in. and nominal wall thickness T = 1.000 in. T = 1.000\text{ in.} T = 1.000 in.
Process 1 (GTAW): Open-root and hot pass depositing t GTAW = 0.200 in. t_{\text{GTAW}} = 0.200\text{ in.} t GTAW = 0.200 in. using ER70S-6.
Process 2 (SMAW): Fill and cap passes depositing t SMAW = 0.800 in. t_{\text{SMAW}} = 0.800\text{ in.} t SMAW = 0.800 in. using E7018 in 5 layers.
Qualified Ranges for Combined Production WPS:
Base Metal Range ( T T T ): Table QW-451.1 for T = 1.0 in. T = 1.0\text{ in.} T = 1.0 in. governs the total joint: Min T = 3 / 16 in. = 0.1875 in. ; Max T = 2 T = 2 × 1.000 = 2.000 in. \text{Min } T = 3/16\text{ in.} = 0.1875\text{ in.}; \quad \text{Max } T = 2T = 2 \times 1.000 = 2.000\text{ in.} Min T = 3/16 in. = 0.1875 in. ; Max T = 2 T = 2 × 1.000 = 2.000 in.
Deposited GTAW ( t GTAW t_{\text{GTAW}} t GTAW ): t = 0.200 in. < 0.75 in. t = 0.200\text{ in.} < 0.75\text{ in.} t = 0.200 in. < 0.75 in. , so: Max t GTAW = 2 × 0.200 = 0.400 in. \text{Max } t_{\text{GTAW}} = 2 \times 0.200 = 0.400\text{ in.} Max t GTAW = 2 × 0.200 = 0.400 in.
Deposited SMAW ( t SMAW t_{\text{SMAW}} t SMAW ): t = 0.800 in. ≥ 0.75 in. t = 0.800\text{ in.} \ge 0.75\text{ in.} t = 0.800 in. ≥ 0.75 in. , and SMAW is one of the processes listed in the Table QW-451.1 note. Therefore the 8 in. heavy-deposit rule applies (the 5-layer count is not a condition): Max t SMAW = 8.000 in. ( 200 mm ) \text{Max } t_{\text{SMAW}} = 8.000\text{ in.} (200\text{ mm}) Max t SMAW = 8.000 in. ( 200 mm )
Qualified Ranges if Extracted as Stand-Alone Single-Process WPSs (QW-200.4(b)):
Stand-Alone GTAW WPS: Base metal thickness is restricted to 2 t GTAW = 2 × 0.200 = 0.400 in. 2t_{\text{GTAW}} = 2 \times 0.200 = 0.400\text{ in.} 2 t GTAW = 2 × 0.200 = 0.400 in. max! (Minimum base metal = 1 / 16 in. 1/16\text{ in.} 1/16 in. per Table QW-451.1 for T ≤ 3 / 8 in. T \le 3/8\text{ in.} T ≤ 3/8 in. ). It cannot weld 2.0 in. 2.0\text{ in.} 2.0 in. base metal alone!
Stand-Alone SMAW WPS: Base metal thickness is qualified from 3 / 16 in. 3/16\text{ in.} 3/16 in. to 2.000 in. 2.000\text{ in.} 2.000 in. (governed by 2 T 2T 2 T ), but must be welded with backing only , because SMAW was deposited over GTAW backing on the coupon.
Scenario 3: GMAW-S Short-Circuiting Pipeline Coupon
PQR Coupon: Fabricated from API 5L X52 pipe ( T = 0.312 in. T = 0.312\text{ in.} T = 0.312 in. / 5 / 16 in. 5/16\text{ in.} 5/16 in. ). Welded full thickness with GMAW-S using ER70S-6, so t = T = 0.312 in. t = T = 0.312\text{ in.} t = T = 0.312 in.
Base Metal Range ( T T T ) — QW-403.10: Because T = 0.312 in. < 0.500 in. T = 0.312\text{ in.} < 0.500\text{ in.} T = 0.312 in. < 0.500 in. , the base metal cap is 1.1 T 1.1T 1.1 T : Min T = 1 / 16 in. = 0.0625 in. ( 1.5 mm ) \text{Min } T = 1/16\text{ in.} = 0.0625\text{ in.} (1.5\text{ mm}) Min T = 1/16 in. = 0.0625 in. ( 1.5 mm ) Max T = 1.1 T = 1.1 × 0.312 in. = 0.3432 in. ( 8.7 mm ) \text{Max } T = 1.1T = 1.1 \times 0.312\text{ in.} = 0.3432\text{ in.} (8.7\text{ mm}) Max T = 1.1 T = 1.1 × 0.312 in. = 0.3432 in. ( 8.7 mm )
Deposited Weld Metal Range ( t t t ) — QW-404.32: Because the deposit t = 0.312 in. < 0.500 in. t = 0.312\text{ in.} < 0.500\text{ in.} t = 0.312 in. < 0.500 in. , the deposit cap is 1.1 t 1.1t 1.1 t : Max t = 1.1 t = 1.1 × 0.312 in. = 0.3432 in. ( 8.7 mm ) \text{Max } t = 1.1t = 1.1 \times 0.312\text{ in.} = 0.3432\text{ in.} (8.7\text{ mm}) Max t = 1.1 t = 1.1 × 0.312 in. = 0.3432 in. ( 8.7 mm )
Contrast with Standard GMAW: If spray transfer had been used, neither special rule would apply; max T T T would be 2 T = 2 × 0.312 = 0.624 in. 2T = 2 \times 0.312 = 0.624\text{ in.} 2 T = 2 × 0.312 = 0.624 in. and max t t t would be 2 t = 0.624 in. 2t = 0.624\text{ in.} 2 t = 0.624 in. — nearly double the short-circuiting limits.
7. Practical Exam Traps & Code Navigation Strategies
The PQR vs. WPQ Trap: Table QW-451.1 governs Procedure Qualification (Article II) , where base metal range is typically 2 T 2T 2 T . Table QW-452.1(b) governs Performance Qualification (Article III) , where welder base metal qualification is essentially unlimited ( T T T max is "Maximum to be welded") for coupons 1 / 2 in. 1/2\text{ in.} 1/2 in. and thicker! Never use QW-452 to calculate procedure limits.
The 3/8" Minimum Thickness Boundary: Coupons 3 / 8 in. 3/8\text{ in.} 3/8 in. thick qualify down to 1 / 16 in. 1/16\text{ in.} 1/16 in. ( 0.0625 in. 0.0625\text{ in.} 0.0625 in. ). However, coupons thicker than 3 / 8 in. 3/8\text{ in.} 3/8 in. (even 0.376 in. 0.376\text{ in.} 0.376 in. ) qualify down only to 3 / 16 in. 3/16\text{ in.} 3/16 in. ( 0.1875 in. 0.1875\text{ in.} 0.1875 in. ). When evaluating production welds between 1 / 16 in. 1/16\text{ in.} 1/16 in. and 3 / 16 in. 3/16\text{ in.} 3/16 in. , a heavy-plate PQR ( T ≥ 1 / 2 in. T \ge 1/2\text{ in.} T ≥ 1/2 in. ) is legally noncompliant!
Importing the Welder Rule into the Procedure Rule: If a problem states a 1.0 in. 1.0\text{ in.} 1.0 in. coupon was welded with 2 passes of submerged arc welding ( t = 1.0 in. t = 1.0\text{ in.} t = 1.0 in. ), the maximum qualified deposit is 8.0 in. 8.0\text{ in.} 8.0 in. , because t ≥ 3 / 4 in. t \ge 3/4\text{ in.} t ≥ 3/4 in. and SAW is a listed process — the pass count is irrelevant under Table QW-451.1. The three-layer condition belongs to welder qualification (Table QW-452.1(b), t ≥ 1 / 2 in. t \ge 1/2\text{ in.} t ≥ 1/2 in. ).
Loading diagram... Figure 4.1: ASME Section IX Procedure Qualification Thickness Logic (Table QW-451.1 & QW-404.32)