Study guide
6.3 Welder Essential Variables: F-Numbers, Backing, and Process Transfers
AWS ASME BPVC Section IX + B31.1/B31.3 Endorsement CWI/SCWI
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Structure, Logistics & Code Navigation Strategy
1.1 Credential Overview, Prometric Delivery & July 2025 Hard-Copy Rule 1.2 The Three-Code Triad: Section IX, B31.1, and B31.3 Roles & Interrelationships 1.3 Rapid Code-Book Navigation: Tabbing, Cross-Referencing & Time Management
2 Chapter 2: Section IX Article I — General Welding Requirements
2.1 Scope, Responsibilities & Section IX Architecture 2.2 Mechanical Test Types, Specimen Dimensions & Acceptance Criteria 2.3 Notch-Toughness Tests, Fillet-Weld Tests & Special Examinations
3 Chapter 3: Section IX Article II — Procedure Qualification Fundamentals
3.1 PQR vs. WPS Workflow, Purpose & Content Requirements 3.2 Coupling and Supporting Multiple WPSs and PQRs 3.3 Test Coupons, Preparation & Required Test Specimen Allocations
4 Chapter 4: Section IX Procedure Qualification Limits & Thickness Rules
4.1 Base Metal & Deposited Weld Metal Thickness Limits 4.2 Impact Testing Requirements & Toughness Thickness Qualification Ranges 4.3 Fillet Weld Procedure Qualification Rules & Special Applications
5 Chapter 5: Section IX Article III — Welder Performance Qualification Fundamentals
5.1 Welder & Welding Operator Qualification Intent, Responsibilities & Identification 5.2 Qualification Testing Methods: Mechanical Bend Tests vs. Volumetric NDE 5.3 Welder Qualification Continuity, Expiration, and Requalification
6 Chapter 6: Section IX Welder Performance Limits, Positions & Diameters
6.1 Test Positions, Groove Weld Orientations & Production Position Limits 6.2 Welder Thickness Limits and Pipe Diameter Qualification Ranges 6.3 Welder Essential Variables: F-Numbers, Backing, and Process Transfers
7 Chapter 7: Section IX Article IV — Welding Variables by Process (Part 1: SMAW & GTAW)
7.1 Understanding Essential, Supplementary Essential & Nonessential Variables 7.2 Shielded Metal Arc Welding (SMAW) Procedure Variables 7.3 Gas Tungsten Arc Welding (GTAW) Procedure Variables
8 Chapter 8: Section IX Article IV — Welding Variables by Process (Part 2: GMAW/FCAW & SAW)
8.1 GMAW & FCAW Procedure Variables and Short-Circuiting Transfer Rules 8.2 Submerged Arc Welding (SAW) Procedure Variables and Flux-Wire Combinations 8.3 Special Variables: Heat Input, Electrical Characteristics & Shielding Gases
9 Chapter 9: Section IX Material Classifications, Numbers & Standard Documentation
9.1 Base Metal P-Numbers, Group Numbers, and S-Numbers 9.2 Filler Metal F-Numbers and As-Deposited Chemistry A-Numbers 9.3 ASME Standard Documentation: Auditing WPS, PQR, and WPQ Forms
10 Chapter 10: ASME B31.1 Power Piping — Scope, Materials, Design & Welding Fabrication
10.1 B31.1 Scope, Jurisdiction, Boiler External Piping vs. Non-Boiler External Piping 10.2 B31.1 Welding Requirements, Joint Alignment, Backing Rings & Tack Welds 10.3 B31.1 Welder & Procedure Qualification Interfacing with Section IX 10.4 B31.1 Materials, Design Conditions & Pressure Design of Components
11 Chapter 11: ASME B31.1 Power Piping — Heat Treatment, Examination, Testing & Fabrication Records
11.1 B31.1 Preheat Rules & Mandatory Temperatures 11.2 B31.1 Postweld Heat Treatment (PWHT) Rules, Temperatures & Holding Times 11.3 B31.1 Mandatory NDE Examination, Acceptance Standards & Pressure Leak Tests 11.4 B31.1 Bending, Forming, Assembly & Code Records
12 Chapter 12: ASME B31.3 Process Piping — Scope, Fluid Services, Materials, Design & Welding
12.1 B31.3 Scope, Fluid Service Classifications & Owner Responsibilities 12.2 B31.3 Welding, Joint Preparation, Backing Rings & Fabrication Details 12.3 B31.3 Procedure & Performance Qualification Rules and Section IX Exceptions 12.4 B31.3 Materials, Design Conditions & Pressure Design of Components
13 Chapter 13: ASME B31.3 Process Piping — Heat Treatment, Examination, Testing, Fabrication & Records
13.1 B31.3 Preheat and Postweld Heat Treatment Rules & Tables 13.2 B31.3 Inspection vs. Examination Responsibilities & Examination Extents 13.3 B31.3 Acceptance Criteria for Weld Imperfections 13.4 B31.3 Pressure Leak Testing: Hydrostatic, Pneumatic & Sensitive Leak Tests 13.5 B31.3 Bending, Forming, Assembly & Records
6.3 Welder Essential Variables: F-Numbers, Backing, and Process Transfers
Key Takeaways Explain This Topic AI
Under ASME Section IX QW-350, welder performance qualification is governed strictly by essential variables; nonessential and supplementary essential variables do not apply to welders.
Table QW-433 dictates F-Number qualification ranges: qualifying with F-No. 4 with backing qualifies F-Nos. 1, 2, 3, and 4 with backing, but does not qualify any F-Number without backing.
Qualifying with F-No. 4 without backing (open root) qualifies F-No. 4 without backing AND qualifies F-Nos. 1, 2, 3, and 4 with backing.
Under QW-402.4 and QW-408.8, the deletion of backing (solid metal backing, weld metal backing, or inert backing gas purge) is an essential variable requiring welder requalification.
Under QW-300.3, welder qualifications cannot be arbitrarily transferred between unrelated employers; an employer may accept another organization's WPQ only under strict operational control agreements or common quality programs, retaining full legal code liability.
Last updated: September 2026
6.3 Welder Essential Variables: F-Numbers, Backing, and Process Transfers
In ASME Section IX Welder Performance Qualification (Article III) , the philosophy of welding variables differs fundamentally from Procedure Qualification (Article II). While a Welding Procedure Specification (WPS) is governed by three distinct tiers of variables— Essential Variables , Supplementary Essential Variables (applicable when notch toughness is mandated), and Nonessential Variables (which may be modified without requalifying the procedure)— welders are governed exclusively by Essential Variables .
Under QW-351 , an essential variable for a welder is defined as any condition where a change in that variable will affect the mechanical dexterity or skill required to deposit sound weld metal. Nonessential variables do not exist for welders. Supplementary essential variables never apply to welders because mechanical properties such as tensile strength, ductility, and Charpy V-notch impact toughness are metallurgical phenomena governed by procedure controls (preheat, heat input, and PWHT), not by the welder's manual coordination.
Process-Specific Welder Essential Variables: QW-350 Series
Article III provides dedicated variable tables for each individual welding process in paragraphs QW-352 through QW-357 . The three most heavily tested tables on the AWS Endorsement examination are QW-353 (SMAW) , QW-355 (GMAW/FCAW) , and QW-356 (GTAW) . +-----------------------------------------------------------------------------------------+
- | WELDER ESSENTIAL VARIABLES BY PROCESS (QW-350) |
- +-----------------------------------------------------------------------------------------+
- | Paragraph | Process | Essential Variables Monitored on WPQ |
- | :-------- | :-------- | :-------------------------------------------------------------- |
- | QW-353 | SMAW | Backing (QW-402.4), Pipe OD (QW-403.16), Base Metal P-No. |
- | | | (QW-403.18), Filler F-No. (QW-404.15), Deposited t (QW-404.30), |
- | | | Position (QW-405.3), Vertical Progression (QW-405.1) |
- | QW-355 | GMAW/FCAW | Backing (QW-402.4), Pipe OD (QW-403.16), Base Metal P-No. |
- | | | (QW-403.18), Filler F-No. (QW-404.15), Deposited t (QW-404.30), |
- | | | Position (QW-405.3), Vertical Progression (QW-405.1), |
- | | | Transfer Mode (QW-409.2), Backing Gas (QW-408.8) |
- | QW-356 | GTAW | Backing (QW-402.4), Pipe OD (QW-403.16), Base Metal P-No. |
- | | | (QW-403.18), Filler Deletion/Addition (QW-404.14), |
- | | | Filler F-No. (QW-404.15), Deposited t (QW-404.30), Position |
- | | | (QW-405.3), Vertical Progression (QW-405.1), Backing Gas |
- | | | (QW-408.8), Current/Polarity (QW-409.4) |
- +-----------------------------------------------------------------------------------------+
- Notable Process-Specific Variables to Memorize
GMAW Mode of Transfer (QW-409.2): A change from spray arc, globular arc, or pulsed arc to short-circuiting transfer (GMAW-S) , or vice-versa, is an essential variable. Short-circuiting transfer operates at lower heat inputs, dramatically increasing the risk of sidewall lack of fusion ("cold lap"). Consequently, qualifying in spray transfer does not qualify a welder for short-circuiting transfer.
GTAW Filler Metal Addition or Deletion (QW-404.14): The deletion or addition of filler metal is an essential variable. A welder who qualifies autogenously (without filler wire) cannot deposit weld metal with filler rod, and vice-versa.
GTAW Current and Polarity (QW-409.4): A change from direct current electrode negative (DCEN) to alternating current (AC) or direct current electrode positive (DCEP) requires requalification.
Filler Metal F-Numbers: The Table QW-433 Qualification Matrix
Filler metals are grouped into F-Numbers (QW-432) based on their operational characteristics and usability. In welder performance qualification, QW-404.15 references Table QW-433 , which governs the substitution ranges of filler metals on production joints.
Overview of Common F-Numbers (QW-432)
F-No. 1: Heavy rutile / iron powder electrodes (e.g., AWS A5.1 E7024, E7028).
F-No. 2: Titania / rutile coated electrodes (e.g., AWS A5.1 E6012, E6013, E6014).
F-No. 3: High-cellulose sodium / potassium coated electrodes (e.g., AWS A5.1 E6010, E6011).
F-No. 4: Basic lime / low-hydrogen coated electrodes (e.g., AWS A5.1 E7015, E7016, E7018, E7048).
F-No. 5: Austenitic and duplex stainless steel coated electrodes (e.g., AWS A5.4 E308L, E309L, E316L, E2209).
F-No. 6: Bare solid wire, cored wire, and rods for GTAW, GMAW, SAW, and PAW (e.g., ER70S-6, ER308L, E71T-1).
The Table QW-433 Master Qualification Rules
Table QW-433 establishes an asymmetric hierarchy for SMAW electrodes (F-Nos. 1 through 4):
- Welder Qualified On: Qualified Production Range: With Backing Qualified Production Range: Without Backing
- F-No. 1 with Backing F-No. 1 None
- F-No. 2 with Backing F-Nos. 1, 2 None
- F-No. 3 with Backing F-Nos. 1, 2, 3 None
- F-No. 4 with Backing F-Nos. 1, 2, 3, 4 None
- F-No. 1 without Backing F-No. 1 F-No. 1
- F-No. 2 without Backing F-Nos. 1, 2 F-No. 2
- F-No. 3 without Backing F-Nos. 1, 2, 3 F-No. 3
- F-No. 4 without Backing F-Nos. 1, 2, 3, 4 F-No. 4
- F-No. 5 with Backing F-No. 5 None
- F-No. 5 without Backing F-No. 5 F-No. 5
- F-No. 6 with Backing F-No. 6 None
F-No. 6 without Backing F-No. 6 F-No. 6 +-----------------------------------------------------------------------------------------+
- | TABLE QW-433 CORE PRINCIPLES TO REMEMBER |
- +-----------------------------------------------------------------------------------------+
- | 1. F-No. 4 WITH Backing qualifies: F-1, F-2, F-3, F-4 WITH Backing ONLY |
- | 2. F-No. 4 WITHOUT Backing qualifies: F-4 WITHOUT Backing AND F-1, F-2, F-3, F-4 WITH |
- | 3. F-No. 4 NEVER qualifies F-No. 5 (Stainless steel is isolated in its own F-Number!) |
- | 4. F-No. 3 WITHOUT Backing NEVER qualifies F-No. 4 WITHOUT Backing |
- +-----------------------------------------------------------------------------------------+
Note
Why F-No. 4 is the Universal Shop Electrode: In structural and pressure vessel fabrication, welders are predominantly qualified using F-No. 4 (E7018) with backing. Under Table QW-433, this single test legally covers the welder to deposit E6010 tack welds or fill passes (F-3), E6013 cosmetic passes (F-2), and E7024 heavy fillets (F-1), provided backing is used.
Backing Variables (QW-402.4) and Inert Gas Purging (QW-408.8)
Under ASME Section IX, joint backing is defined as any material placed at the root of a weld joint to support and shield molten weld metal.
Types of Backing Recognized by Section IX
Solid Metal Backing: Commercial backing rings, permanent backing strips, or split rings.
Weld Metal Backing: Back welds or double-welded joints where the second side is deposited after back-gouging or grinding to sound metal.
Nonmetallic / Removable Backing: Ceramic backing tapes, flux backing, or copper backing shoes.
The Deletion of Backing Variable (QW-402.4)
Under QW-402.4 , the deletion of backing in a groove weld is an essential variable for welders: Tested WITH Backing ===> Qualified WITH Backing ONLY
Tested WITHOUT Backing (Open) ===> Qualified WITH and WITHOUT Backing
If a welder passes a test on a groove weld with a steel backing strip (or on a double-welded joint), that welder is legally barred from welding an open-root joint in production. Conversely, a welder who proves their ability to control root penetration and keyholing on an open-root coupon without backing is qualified to weld with backing, without backing, or on double-welded joints.
Inert Gas Purge / Backing Gas (QW-408.8)
In GTAW and GMAW processes—particularly when welding stainless steels (P-No. 8), nickel alloys (P-No. 4X), and low-alloy chrome-moly steels (P-No. 4, 5A)—internal purging with an inert gas (such as argon or nitrogen) is mandatory to prevent severe root oxidation, commonly known as "sugaring" .
Under QW-408.8 , the deletion of backing gas is an essential variable:
If a welder qualifies a GTAW open-root joint using an argon purge (backing gas), the welder cannot weld in production without an argon purge.
However, the addition of backing gas is not an essential variable for welders (it makes root shielding easier, not harder).
Welder Performance Qualification Transfers (QW-300.3) & Third-Party Testing
A critical administrative aspect of ASME Section IX is the principle of Manufacturer Responsibility established in QW-103 and QW-300.2 :
Important
The Cardinal Rule of ASME Qualifications: Each manufacturer or contractor is responsible for the welding done by their organization and shall conduct the tests required to qualify the welding procedures, welders, and welding operators .
Can Welder Qualifications Be Transferred Between Employers? (QW-300.3)
Historically, when a welder changed employers, their qualification expired immediately; the new employer had to re-test the welder. However, ASME Section IX QW-300.3 permits the acceptance of performance qualifications across organizations under strictly controlled conditions:
Operational Control Agreements: Two or more companies with identical or unified Quality Management Systems (such as a parent company and subsidiaries, or a formal joint venture consortium) may share welder performance qualifications, provided a single designated quality program governs the welding operations.
Common Qualification Programs: When an employer participates in an accredited, industry-wide welder qualification program (such as the AWS National Welder Certification program or an owner-managed refinery contractor qualification database), the employer may accept another organization's WPQ provided:
The new employer obtains the original WPQ record from the qualifying organization.
The employer verifies that the welder's continuity has been maintained without a lapse exceeding six months under QW-322.1 .
The employer's designated representative signs and dates the accepted WPQ, accepting full legal and code responsibility for the welder's production work.
Third-Party Testing Laboratory Limitations
A commercial independent testing laboratory or third-party inspection agency may:
Prepare test specimens (machining bend straps, tensile specimens).
Perform mechanical testing (bending coupons, pulling tensiles).
Conduct non-destructive examination (radiography, ultrasonic testing).
Record raw test results on a certified lab test report.
However, the testing agency CANNOT qualify the welder on behalf of the manufacturer! The manufacturer's or contractor's own supervisory personnel must observe the test coupon welding, verify compliance with the qualified WPS, and sign the official WPQ Form QW-484. A WPQ bearing only the signature of an outside testing agency without the manufacturer's operational acceptance is completely invalid under ASME Section IX.
- Real-World Inspection Scenario & Common Exam Traps
- Scenario: The Pipeline Tie-In Open-Root Violation
A mechanical contractor is prefabricating natural gas station piping designed under ASME B31.3 Normal Fluid Service. The qualified WPS specifies an open-root joint using AWS A5.1 E6010 (F-No. 3) for the root pass, followed by AWS A5.1 E7018 (F-No. 4) for the hot pass, fill, and cap passes.
The contractor hires three welders whose WPQ records show they were qualified by their previous employer on an NPS 6 pipe coupon in the 6G position using AWS A5.1 E7018 (F-No. 4) with a steel backing strip . The contractor's QC manager reasons that:
The 6G test qualifies all positions.
Under Table QW-433, F-No. 4 qualifies F-Nos. 1, 2, 3, and 4.
Therefore, the welders are qualified to weld the entire open-root joint.
The Certified Welding Inspector (CWI) halts fabrication and rejects the WPQs on two major code violations:
Violation 1 (Backing): The welders tested with backing . Under QW-402.4 and Table QW-433, testing with backing qualifies them to weld with backing only . They have zero qualification to weld an open-root joint without backing.
Violation 2 (F-Number Root Progression): Table QW-433 states that qualifying with F-No. 4 with backing qualifies F-No. 3 with backing only . To weld an open-root E6010 pass, a welder must test on an open-root coupon using F-No. 3 (or F-No. 4 without backing).
Common Exam Traps to Avoid
The F-No. 4 to F-No. 5 Fallacy: Assuming that because F-No. 4 is the highest carbon steel manual electrode, it qualifies stainless steel (F-No. 5). It does not; F-No. 5 is an independent filler metal family.
The Open-Root Assumption: Assuming that passing an open-root F-No. 3 (E6010) test qualifies open-root F-No. 4 (E7018). It does not; Table QW-433 explicitly limits F-3 without backing to F-3 without backing, and F-1, F-2, F-3 with backing.
The Purge Gas Addition Trap: Thinking that adding backing gas to a GTAW weld requires requalifying the welder. Under QW-408.8, only the deletion of backing gas requires requalification.
The Testing Lab Signature Trap: Believing a WPQ is legally valid because an accredited testing laboratory signed it. Without the employing manufacturer's operational signature, the document has zero standing under ASME Section IX.