Study guide
7.2 Table 8.1 Visual Inspection Criteria: Static vs. Cyclic Non-Tubular Connections
AWS D1.1 Structural Steel Endorsement Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Structure, Code Scope & General Requirements
1.1 AWS D1.1 Endorsement Exam Format & Open-Book Navigation 1.2 Clause 1 Scope, Responsibilities & Structural Classifications 1.3 Normative References, Terminology & Base Metal Scope
2 Chapter 2: Design of Welded Connections (Clause 4)
2.1 Groove and Fillet Weld Design & Effective Throat Calculations 2.2 Statically Loaded Connection Details, Geometry Limits & Transitions 2.3 Cyclically Loaded Structures, Stress Categories & Fatigue Life Design
3 Chapter 3: Prequalification of Welding Procedure Specifications (Clause 5)
3.1 Prequalified Processes, Base Metal Groups & Matching Filler Metals 3.2 Prequalified Joint Geometries, CJP/PJP Details & Backing 3.3 Prequalified Minimum Fillet Sizes & Preheat/Interpass Temperatures
4 Chapter 4: Welding Procedure Specification (WPS) Qualification (Clause 6, Part B)
4.1 WPS Qualification Requirements, PQR Coupon Testing & Mechanical Evaluation 4.2 PQR Mechanical Test Types: Tension, Guided Bend & Macroetch 4.3 WPS Essential Variables, Base Metal Ranges & Qualified Positions (Table 6.6)
5 Chapter 5: Welder, Welding Operator & Tack Welder Performance Qualification (Clause 6, Part C)
5.1 Welder Qualification Test Plates, Positions & Pipe Assemblies 5.2 Performance Test Evaluation (Visual, Guided Bend, Macroetch) & Retest Rules 5.3 Performance Essential Variables, Qualification Limits (Table 6.12) & Continuity
6 Chapter 6: Fabrication & Workmanship (Clause 7)
6.1 Base Metal Preparation, Thermal Cutting Tolerances & Fit-Up 6.2 Welding Consumable Storage, Low-Hydrogen Exposure Limits & Baking 6.3 Distortion Control, Arc Strikes, Tack Welds & Weld Repair Rules
7 Chapter 7: Visual Inspection & Acceptance Criteria (Clause 8, Parts A-C)
7.1 Inspector Responsibilities, Qualifications (CWI/SCWI) & Inspection Sequence 7.2 Table 8.1 Visual Inspection Criteria: Static vs. Cyclic Non-Tubular Connections 7.3 Weld Profiles, Undercut Tolerances, Porosity Limits & Crack Rejection
8 Chapter 8: Nondestructive Testing (NDT) Procedures & Acceptance (Clause 8, Part D)
8.1 Radiographic Testing (RT) Requirements, IQI Placement & Acceptance 8.2 Ultrasonic Testing (UT) Procedures, Calibration & Tables 8.2 / 8.3 8.3 Magnetic Particle (MT), Liquid Penetrant (PT) & Inspection Records
9 Chapter 9: Stud Welding & Tubular Structures (Clauses 9 & 10)
9.1 Clause 9 Stud Welding: Pre-Production Testing, Bend Tests & Flash Acceptance 9.2 Clause 10 Tubular Connections: T-, Y-, K-Joints, Geometry & Effective Throat 9.3 Clause 10 Tubular Qualification & Inspection: 6GR Restriction Testing & Acceptance
10 Chapter 10: Strengthening/Repair of Existing Structures & Welding Symbols (Clause 11 & AWS A2.4)
10.1 Clause 11 Evaluation, Base Metal Identification & Welding Under Load 10.2 Clause 11 Repair Workmanship, Heat Input Control & Member Restoration 10.3 AWS A2.4 Welding Symbols: Notation, Sizing, Pitch & Field Flags
7.2 Table 8.1 Visual Inspection Criteria: Static vs. Cyclic Non-Tubular Connections
Key Takeaways Explain This Topic AI
Crack prohibition is absolute across all AWS D1.1 categories: zero cracks of any size or type are permitted in either the weld metal or the heat-affected zone (HAZ).
Complete fusion must exist between adjacent passes of weld metal and between the weld metal and base metal, strictly prohibiting cold lap and lack of sidewall fusion.
All weld craters must be filled to their full cross section, except for the non-effective run-off ends of intermittent fillet welds.
Visual inspection for ASTM A514, A517, and A709 Grades 100/100W quenched and tempered steels must be delayed at least 48 hours post-welding to detect delayed hydrogen cracking.
Table 8.1 differentiates acceptance criteria across Statically Loaded Nontubular, Cyclically Loaded Nontubular, and Tubular Connections based on fatigue sensitivity.
Last updated: August 2026
Table 8.1 Visual Inspection Criteria: Static vs. Cyclic Connections
Table 8.1 of AWS D1.1/D1.1M:2025 is the single most critical inspection table in structural welding. It codifies the visual acceptance criteria for all production welds, establishing the precise boundary between acceptable workmanship and rejectable discontinuities.
Table 8.1 is structured into three distinct structural categories:
- Statically Loaded Nontubular Connections (buildings, standard industrial frameworks)
- Cyclically Loaded Nontubular Connections (bridges, crane runway girders, vibrating equipment supports)
- Tubular Connections (offshore jackets, tubular trusses, pipe structures)
Understanding the technical rationale, zero-tolerance rules, and service-dependent criteria within Table 8.1 is essential for every CWI and endorsement candidate.
Structural Hierarchy of Table 8.1 Visual Acceptance Criteria +-------------------------------------------------------------------------+
- | AWS D1.1 TABLE 8.1 ACCEPTANCE ARCHITECTURE |
- +-------------------------------------------------------------------------+
- | DISCONTINUITY CATEGORY | STATIC NONTUBULAR | CYCLIC NONTUBULAR |
- +--------------------------+---------------------+-----------------------+
- | 1. CRACKS | ZERO TOLERANCE (0) | ZERO TOLERANCE (0) |
- | 2. FUSION (LACK OF) | ZERO TOLERANCE (0) | ZERO TOLERANCE (0) |
- | 3. CRATER CROSS SECTION | FILLED FULLY* | FILLED FULLY* |
- | 4. WELD PROFILES | FIG 7.4 / TAB 7.9 | FIG 7.4 / TAB 7.9 |
- | 5. TIME OF INSPECTION | UPON COOLING | UPON COOLING |
- | (A514/A517/A709 100) | >= 48 HOURS DELAY | >= 48 HOURS DELAY |
- | 6. UNDERCUT | 1/32 in. / 1/16 in. | 0.01 in. / 1/32 in. |
- | 7. PIPING POROSITY | Trans. Tens.: ZERO | Trans. Tens.: ZERO |
- | | Other: <=3/8"/in., | Other: Max 1 in 4", |
- | | <=3/4"/12" | Dia <= 3/32" |
- +-------------------------------------------------------------------------+
* Exception: Ends of intermittent fillet welds outside effective length.
The Universal Zero-Tolerance Rules (Categories 1 – 3)
Regardless of whether a connection is subject to static or fatigue loading, AWS D1.1 enforces absolute zero tolerance for planar, notch-like discontinuities that cause immediate structural failure.
1. Category 1: Crack Prohibition (Table 8.1 Item 1)
Rule: Any crack shall be unacceptable , regardless of its size, orientation, or location.
Scope: Applies to longitudinal cracks, transverse cracks, root cracks, toe cracks, centerline solidification cracks, crater cracks, and micro-fissures in both the weld metal and the Heat-Affected Zone (HAZ) .
Engineering Basis: Cracks represent infinitely sharp stress risers ( K t → ∞ K_t \to \infty K t → ∞ ). Under service loads, stress intensity ( K I K_I K I ) at the crack tip immediately propagates brittle fracture or rapid fatigue crack growth.
2. Category 2: Weld/Base Metal Fusion (Table 8.1 Item 2)
Rule: Thorough fusion shall exist between adjacent layers of weld metal and between weld metal and base metal.
Defects Prohibited: Lack of sidewall fusion, lack of interpass fusion, lack of root penetration, and overlap (cold lap) .
Verification: Weld toes must blend smoothly into the base metal without rolling over unfused base metal.
3. Category 3: Crater Cross Section (Table 8.1 Item 3)
Rule: All craters shall be filled to the full cross section of the weld.
Intermittent Fillet Weld Exception: The only exception permitted by code applies to the terminations of intermittent fillet welds outside their specified effective length .
Engineering Basis: Unfilled craters develop deep crater pipes and radial shrinkage star cracks during pool solidification due to high volumetric contraction.
Category 5: Time of Inspection & The 48-Hour Delay Rule
AWS D1.1 Table 8.1 Item 5 specifies when visual inspection may officially be performed and signed off. +-------------------------------------------------------------------------+
- | TIME OF VISUAL INSPECTION (TABLE 8.1 ITEM 5) |
- +-------------------------------------------------------------------------+
- | |
- | [ STANDARD CARBON & LOW-ALLOY STEELS ] (ASTM A36, A572, A992, A588) |
- | --> Visual inspection may begin IMMEDIATELY after weld cools to |
- | ambient shop/site temperature. |
- | |
- | [ HIGH-STRENGTH QUENCHED & TEMPERED STEELS ] |
- | (ASTM A514, ASTM A517, ASTM A709 Grades 100 & 100W - Fy = 100 ksi) |
- | --> Visual inspection SHALL NOT BE PERFORMED until AT LEAST |
- | 48 HOURS AFTER COMPLETION OF WELDING! |
- | |
- +-------------------------------------------------------------------------+
- Technical Rationale for the 48-Hour Delay
Quenched and tempered high-yield-strength steels ( F y = 100 ksi F_y = 100\text{ ksi} F y = 100 ksi [ 690 MPa 690\text{ MPa} 690 MPa ]) possess high hardenability. When welded, the coarse-grained HAZ forms a highly stressed, untempered martensitic microstructure.
Any diffusible hydrogen ( H + H^+ H + ) present in the weld matrix slowly migrates toward areas of high triaxial tensile stress.
Delayed Hydrogen-Assisted Cracking (HAC) —also known as underbead cold cracking—typically incubates and propagates over a period of 12 to 48 hours after the joint cools.
Inspecting welds before the 48-hour incubation window elapses risks approving welds containing hidden or emerging sub-surface and toe cracks.
Detailed Side-by-Side Comparison: Static vs. Cyclic Criteria
- Discontinuity / Criterion Statically Loaded Nontubular Cyclically Loaded Nontubular Tubular Connections
- 1. Cracks None permitted (Zero) None permitted (Zero) None permitted (Zero)
- 2. Weld/Base Metal Fusion Thorough fusion required Thorough fusion required Thorough fusion required
3. Crater Cross Section Filled full (except intermittent ends) Filled full (except intermittent ends) Filled full (except intermittent ends)
4. Weld Profiles Conforms to Fig 7.4 / Tab 7.9 Conforms to Fig 7.4 / Tab 7.9 Conforms to Table 10.14
5. Time of Inspection Ambient cooling; ≥ 48 hr \ge 48\text{ hr} ≥ 48 hr for A514/A517 Ambient cooling; ≥ 48 hr \ge 48\text{ hr} ≥ 48 hr for A514/A517 Ambient cooling; ≥ 48 hr \ge 48\text{ hr} ≥ 48 hr for A514/A517
6. Undercut t < 1 in. t < 1\text{ in.} t < 1 in. : ≤ 1 / 32 in. \le 1/32\text{ in.} ≤ 1/32 in. ; allowable ≤ 1 / 16 in. \le 1/16\text{ in.} ≤ 1/16 in. for 2 in. 2\text{ in.} 2 in. in 12 in. 12\text{ in.} 12 in. ; t ≥ 1 in. t \ge 1\text{ in.} t ≥ 1 in. : ≤ 1 / 16 in. \le 1/16\text{ in.} ≤ 1/16 in. any length Primary transverse tension: ≤ 0.01 in. \le 0.01\text{ in.} ≤ 0.01 in. [ 0.25 mm 0.25\text{ mm} 0.25 mm ]; All other: ≤ 1 / 32 in. \le 1/32\text{ in.} ≤ 1/32 in. [ 1.0 mm 1.0\text{ mm} 1.0 mm ] t ≤ 5 / 8 in. t \le 5/8\text{ in.} t ≤ 5/8 in. : ≤ 1 / 32 in. \le 1/32\text{ in.} ≤ 1/32 in. ; t > 5 / 8 in. t > 5/8\text{ in.} t > 5/8 in. : ≤ 1 / 16 in. \le 1/16\text{ in.} ≤ 1/16 in.
7. Piping Porosity (CJP Transverse Tension) None permitted (Zero) None permitted (Zero) None permitted (Zero)
8. Piping Porosity (Other Welds) ≤ 3 / 8 in. \le 3/8\text{ in.} ≤ 3/8 in. in any linear inch; ≤ 3 / 4 in. \le 3/4\text{ in.} ≤ 3/4 in. in any 12 in. 12\text{ in.} 12 in. Max 1 pore in 4 in. 4\text{ in.} 4 in. ; Max diameter = 3 / 32 in. = 3/32\text{ in.} = 3/32 in. Max 1 pore in 4 in. 4\text{ in.} 4 in. ; Max diameter = 3 / 32 in. = 3/32\text{ in.} = 3/32 in.
- Worked Example: Static vs. Cyclic Inspection Determination
- Problem Statement
A fabricator completes two identical Complete Joint Penetration (CJP) groove welds using E7018 on 1-1/2 in. [38 mm] thick ASTM A572 Grade 50 plate:
Weld A is installed in a building roof truss tension chord (statically loaded).
Weld B is installed in a dynamic overhead bridge crane runway girder flange subject to transverse cyclic tension.
During visual inspection, the CWI notes the following on each weld:
A localized undercut measuring 0.045 in. [1.14 mm] deep over a length of 1.5 in.
One isolated surface piping porosity pore measuring 1/16 in. [1.6 mm] in diameter.
Evaluate the code acceptance of Weld A and Weld B under Table 8.1.
Step-by-Step Code Evaluation
Evaluate Weld A (Statically Loaded Nontubular):
Undercut: Plate thickness t = 1.5 in. ≥ 1.0 in. t = 1.5\text{ in.} \ge 1.0\text{ in.} t = 1.5 in. ≥ 1.0 in.
Under Table 8.1 Item 7(A), for t ≥ 1 in. t \ge 1\text{ in.} t ≥ 1 in. , undercut ≤ 1 / 16 in. \le 1/16\text{ in.} ≤ 1/16 in. ( 0.0625 in. 0.0625\text{ in.} 0.0625 in. ) is acceptable for any length.
Measured undercut = 0.045 in. < 0.0625 in. = 0.045\text{ in.} < 0.0625\text{ in.} = 0.045 in. < 0.0625 in. ; Undercut is ACCEPTABLE.
Piping Porosity: Weld A is a CJP butt joint in a tension chord (transverse to computed tensile stress).
Under Table 8.1 Item 8(A), CJP groove welds in butt joints transverse to computed tensile stress shall have NO visible piping porosity .
Result for Weld A: REJECTED due to the presence of visible piping porosity in a transverse tension butt joint.
Evaluate Weld B (Cyclically Loaded Nontubular):
Undercut: Primary member under transverse tensile stress.
Under Table 8.1 Item 7(B), undercut shall not exceed 0.01 in. [0.25 mm] .
Measured undercut = 0.045 in. > 0.010 in. = 0.045\text{ in.} > 0.010\text{ in.} = 0.045 in. > 0.010 in. ; Undercut is REJECTABLE.
Piping Porosity: CJP groove weld in transverse cyclic tension.
Under Table 8.1 Item 8(B), NO visible piping porosity is permitted.
Result for Weld B: REJECTED on two independent grounds (undercut exceeding 0.01 in. and presence of piping porosity).