Study guide

9.3 Excavation, Trenching & Electrical Safety

Arizona General Contractor Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & Exam Overview

1.1 Current Exam Facts 1.2 The Arizona Contractor Licensing Path 1.3 How to Use This Guide & Study Plan

2 Chapter 2: Arizona ROC & Licensing Law

2.1 The Arizona Registrar of Contractors 2.2 License Classifications 2.3 Qualifying Party & Experience Requirements 2.4 Application, Fees, Bond & Background Check 2.5 License Bonds, Cash Deposits & Bond Claims 2.6 Unlicensed Contracting: Penalties & Lost Remedies 2.7 Advertising Rules, Contract Disclosures & Workmanship Standards

3 Chapter 3: The Exams — SRE, Trade & NASCLA

3.1 The Statutes & Rules Exam (SRE) 3.2 The PSI Trade Exam 3.3 The NASCLA Commercial General Building Exam Option

4 Chapter 4: License Maintenance, Recovery Fund & Discipline

4.1 License Renewal & Continuing Education 4.2 The Residential Contractors' Recovery Fund 4.3 ROC Disciplinary Actions & Penalties

5 Chapter 5: Contract Law & Disputes

5.1 Arizona Contract Fundamentals 5.2 Construction Contract Terms & Provisions 5.3 Change Orders & Modifications 5.4 Dispute Resolution & ROC Complaints 5.5 The Arizona Prompt Payment Act

6 Chapter 6: Liens, Bonds & Insurance

6.1 Arizona Mechanics' Lien Law Overview 6.2 Lien Notices, Recording & Deadlines 6.3 Contract Bonds: Bid, Performance & Payment 6.4 Insurance Requirements

7 Chapter 7: Financial Management & Taxes

7.1 Accounting & Financial Statements 7.2 Estimating, Bidding & Markup 7.3 Taxes & Payroll

8 Chapter 8: Project Management

8.1 Scheduling & the Critical Path Method 8.2 Supervision, Subcontractors & Quality Control 8.3 Project Documentation & Closeout

9 Chapter 9: Safety & OSHA

9.1 OSHA Construction Standards Overview 9.2 Fall Protection, Scaffolds & Ladders 9.3 Excavation, Trenching & Electrical Safety 9.4 Heat Illness Prevention & Arizona Job-Site Hazards

10 Chapter 10: Building Codes, Permits & Plan Reading

10.1 IRC 2018 & IBC 2018 Fundamentals 10.2 Permits, Plan Review & Inspections 10.3 Energy Code & Accessibility 10.4 Reading Construction Drawings & Specifications 10.5 Means of Egress & Fire-Resistance-Rated Construction

11 Chapter 11: Sitework, Concrete & Masonry

11.1 Sitework: Surveying, Excavation & Grading 11.2 Concrete: Formwork, Reinforcement & Placing 11.3 Masonry: Brick, Block & Mortar 11.4 Soils, Compaction & Earthwork Testing 11.5 Concrete Materials & Mix Design 11.6 Concrete Curing, Joints, Testing & Defects 11.7 Masonry Reinforcement, Grouting & Wall Systems

12 Chapter 12: Carpentry, Metals & Building Envelope

12.1 Carpentry & Framing 12.2 Metals & Metal Framing 12.3 Thermal & Moisture Protection 12.4 Doors, Windows & Finishes 12.5 Engineered Wood, Trusses & Connectors 12.6 Structural Steel Erection & Connections 12.7 Steel Joists, Girders & Metal Deck

13 Chapter 13: Roofing, Waterproofing & Interior Finishes

13.1 Roofing Systems 13.2 Waterproofing, Flashing & Sealants 13.3 Interior Finishes: Gypsum, Stucco, Flooring & Paint

14 Chapter 14: Building Systems for the General Contractor

14.1 Mechanical & Plumbing Systems 14.2 Electrical Systems & Temporary Power

9.3 Excavation, Trenching & Electrical Safety

Key Takeaways Explain This Topic AI

Excavations and trenches 5 feet or deeper require a protective system (sloping, shoring, shielding, or benching) unless entirely in stable rock.

A competent person must inspect every excavation before workers enter each shift and after any condition-changing event.

Spoil piles, equipment, and materials must be kept at least 2 feet back from the excavation edge.

OSHA requires GFCI protection on all 120V, 15A or 20A construction-site receptacles, unless an assured equipment grounding conductor program is used.

Minimum clearance from overhead power lines up to 50 kV is 10 feet; greater voltages require 10 ft plus 0.4 in per kV over 50 kV.

Last updated: August 2026

Excavation and Trenching Standards (29 CFR 1926.650–652)

Excavation and trenching are among the most hazardous construction operations, responsible for dozens of fatalities each year from cave-ins. The OSHA excavation standards are in Subpart P of 29 CFR 1926:

  • 1926.650 — scope, application, and definitions
  • 1926.651 — specific excavation requirements (access/egress, spoil piles, utilities)
  • 1926.652 — protective systems (sloping, shoring, shielding)
  • Key Definitions
  • Excavation — any human-made cut, cavity, trench, or depression in the earth's surface formed by earth removal
  • Trench — a narrow excavation (depth greater than width) that is no more than 15 feet wide at the bottom

Competent person — one who is capable of identifying existing and predictable hazards in the surroundings or working conditions and is authorized to take prompt corrective action to eliminate them

The Competent Person

Every excavation must be inspected daily by a competent person before workers enter. The competent person must:

  • Inspect excavations, adjacent areas, and protective systems daily before work begins
  • Inspect after rainstorms, hazardous substance leaks, or any occurrence that could change conditions
  • Remove employees from the excavation immediately if a hazard is found
  • Determine the appropriate protective system based on soil classification and site conditions

Quick Answer: A competent person must inspect every excavation before workers enter each shift and after any event that could change conditions, and must have authority to stop work and remove workers.

Soil Classification

OSHA classifies soils into four types, which determine the required sloping angle:

  • Soil Type Description Maximum Allowable Slope (for excavations <20 ft deep)
  • Stable Rock Natural solid mineral matter that can stay vertical Vertical (90°)

Type A Cohesive soils (clay, hardpan, silty clay) with high compressive strength; not previously disturbed 3/4H:1V (53°)

Type B Cohesive but less stable; granular cohesionless soils; previously disturbed soils 1H:1V (45°)

Type C Granular soils including gravel, sand, loamy sand, submerged soil, rock that is not stable 1-1/2H:1V (34°)

Trench Protective Systems

For trenches 5 feet or deeper , one of the following protective systems is required (unless the excavation is entirely in stable rock):

System Description Best Suited For

Sloping Cutting the trench wall back to a safe angle per soil type Open sites with room to cut back; Type A or B soils

Shoring Installing hydraulic, timber, or screw-jack support to prevent wall collapse Restricted sites where sloping is not feasible

Shielding Using a trench box or trench shield to protect workers from cave-ins Common in urban utility work; does not prevent collapse but protects workers

Benching Excavating in horizontal steps Type A or B soils (not allowed in Type C soil)

For excavations deeper than 20 feet , a registered professional engineer must design the protective system.

Access, Egress, and Spoil Piles

Access/egress: Ramps, ladders, or stairways must be located so no worker has to travel more than 25 feet laterally to exit any trench 4 feet or deeper

Spoil piles, equipment, and materials: Must be kept at least 2 feet back from the edge of the excavation to prevent material from falling onto workers

Utilities: Must be located and identified before excavation begins; in Arizona, contact the utility locator service (Arizona 811 / Blue Stake) at least two full working days before digging

Surface water: Must be controlled; dewatering used as needed; competent person re-inspects after rain

Hazardous atmospheres: Test for oxygen deficiency, flammable gases, and toxic fumes in excavations deeper than 4 feet where oxygen deficiency or hazardous atmosphere could exist

Electrical Safety (29 CFR 1926, Subpart K)

Electrical hazards cause both electrocution (a Focus Four hazard) and construction-site fires. Subpart K covers installation safety, grounding, and safe work practices for both temporary wiring and permanent installations.

Lockout/Tagout (LOTO)

Before any maintenance or service work on energized systems where workers could be exposed to unexpected start-up or stored energy, lockout/tagout (LOTO) procedures must be applied:

  • Notify all affected employees
  • Identify and isolate the energy source
  • Lock and tag the isolating device with the worker's unique lock and tag
  • Dissipate or restrain any stored energy (capacitors, springs, hydraulic pressure)
  • Verify isolation before beginning work — try to start the equipment
  • Remove locks and tags only when work is complete, and only by the person who applied them
  • GFCI and Assured Equipment Grounding

OSHA requires protection against ground-fault hazards on construction sites through one of two methods:

Method Requirement

Ground-Fault Circuit Interrupters (GFCI) Required on all 120V, single-phase, 15A and 20A receptacles used for construction tools and equipment; most common and simplest compliance method

Assured Equipment Grounding Conductor Program A written, employer-administered program that tests all cord sets, receptacles, and cord-and-plug-connected equipment for continuous grounding continuity at regular intervals

Quick Answer: OSHA requires GFCI protection on all 120V, 15A and 20A construction-site receptacles. An assured equipment grounding conductor program is the only alternative.

Overhead Power-Line Clearance

When equipment (cranes, ladders, scaffolds, long-handled tools) may come near overhead power lines, the employer must either de-energize and ground the lines , maintain the minimum required clearance , or use physical barriers and a dedicated spotter .

  • Line Voltage Minimum Clearance
  • Up to 50 kV 10 feet
  • Over 50 kV 10 ft + 0.4 in per kV over 50 kV

For example, a 138 kV line requires 10 ft + (138 − 50) × 0.4 in = 10 ft + 35.2 in ≈ 12 ft 11 in of clearance. When in doubt, treat every overhead line as energized until the utility confirms otherwise.