Study guide

10.2 Refrigerant Copper Piping: ACR Tubing, Brazing with Nitrogen Purge & Trapping

Arizona HVAC Contractor License ROC R-39R/C-39/CR-39

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Arizona ROC Licensing & Legal Framework

1.1 Arizona ROC Authority & License Classifications 1.2 Application Requirements, Qualifying Party Duties & Experience Standards 1.3 Contractor Bonds, Financial Requirements & Residential Recovery Fund 1.4 Arizona Prompt Pay Act, Contracting Requirements & Mechanic's Liens 1.5 ROC Workmanship Standards, Complaint Investigation, Citations & Disciplinary Procedures

2 Chapter 2: Thermodynamics & The Vapor Compression Refrigeration Cycle

2.1 Thermodynamic Fundamentals, Heat Transfer & Pressure-Temperature Relationships 2.2 The Four Primary Cycle Components: Compressors, Condensers, Metering Devices & Evaporators 2.3 Superheat & Subcooling: Measurement, Calculation & Diagnostic Interpretation 2.4 Pressure-Enthalpy (P-h) Diagrams & System Operating Analysis 2.5 Refrigerant Characteristics, Oil Miscibility & ASHRAE Safety Classifications

3 Chapter 3: Refrigerant Management, EPA Section 608 & Environmental Compliance

3.1 EPA Clean Air Act Section 608 Regulations, Certifications & Venting Prohibitions 3.2 Recovery, Recycling & Reclaim Standards, Evacuation Levels & Deep Vacuum Procedures 3.3 Leak Detection Methods & Mandatory Repair Trigger Rates 3.4 Low-GWP Refrigerants & A2L Transition Safety Requirements 3.5 System Evacuation, Triple Evacuation Method, Vacuum Decay Testing & Moisture Removal

4 Chapter 4: Heating Systems: Gas Furnaces, Electric Heat & Combustion Safety

4.1 Fuel Gas Combustion Chemistry, Gas Burners & Orifice Sizing 4.2 Gas Furnace Components, Ignition Systems & Flame Rectification 4.3 Furnace Safety Controls & Troubleshooting Sequences 4.4 Gas Venting Categories (I-IV), Vent Sizing & Combustion Air Calculations 4.5 Electric Furnaces & Duct Heaters: Sizing, Sequencers, Thermal Cutoffs & Wiring

5 Chapter 5: Heat Pump Systems & Defrost Operation

5.1 Heat Pump Operating Principles & Reversing Valve Operation 5.2 Thermal Expansion Valves (TXVs), Electronic Expansion Valves (EEVs) & Bi-flow Metering 5.3 Defrost Systems: Time-Temperature vs. Demand Defrost Cycles & Sensor Operation 5.4 Heat Pump Balance Point Analysis, Supplemental Strip Heat Staging & Emergency Heat 5.5 Inverter-Driven Variable Capacity Systems & Desert Heat Pump Performance

6 Chapter 6: Air Distribution, Duct Design & Airflow Dynamics

6.1 Airflow Fundamentals: CFM Requirements, Velocity, Static Pressure & TESP 6.2 ACCA Manual D Duct Sizing: Equal Friction Method & Friction Rate Calculations 6.3 Duct Construction, Materials & SMACNA Support Standards 6.4 Duct Sealing (UL 181 Standards, Mastic, Tapes), Attic Insulation & Leakage Testing 6.5 Air System Balancing, Diagnostic Instruments & Grille/Register Selection

7 Chapter 7: Psychrometrics & Desert Climate HVAC Load Sizing

7.1 The Psychrometric Chart: Dry-Bulb, Wet-Bulb, Relative Humidity, Enthalpy & Dew Point 7.2 Psychrometric Air Conditioning Processes: Cooling, Heating, Humidification & Dehumidification 7.3 ACCA Manual J Residential Load Calculations: Heat Gain, Heat Loss, U-Values & SHGC 7.4 Arizona Desert Climate Design Considerations: Sensible Heat Ratios & Manual S Sizing 7.5 Evaporative Cooling Systems (Direct & Indirect Swamp Coolers): Principles & Maintenance

8 Chapter 8: HVAC Electrical Systems, Motors & Control Circuits

8.1 Electrical Fundamentals for HVAC: Ohm's Law, Power Formula & Single/Three-Phase Power 8.2 24VAC Control Circuits, Step-Down Transformers, Relays & Contactors 8.3 Capacitors (Start & Run), Potential Relays & Motor Starting Circuits 8.4 HVAC Motors: PSC, ECM & Three-Phase Motors 8.5 NEC Article 440 Compliance: MCA, MOCP & Disconnect Switch Rules

9 Chapter 9: Hydronics, Boilers, Chilled Water & Commercial Systems

9.1 Hydronic Heating Systems: Low-Pressure Hot Water & Steam Boilers 9.2 Hydronic Specialties: Air Separators, Expansion Tanks, Circulator Pumps & Zone Valves 9.3 Water Piping Systems, Sizing, Flow Rates & Relief Valves 9.4 Commercial Chilled Water Systems: Air-Cooled & Water-Cooled Chillers 9.5 Cooling Towers, Condenser Water Loops & Legionella Water Treatment

10 Chapter 10: Codes, Piping Systems, Safety & OSHA Standards

10.1 International Mechanical Code (IMC) & International Fuel Gas Code (IFGC) Compliance 10.2 Refrigerant Copper Piping: ACR Tubing, Brazing with Nitrogen Purge & Trapping 10.3 Fuel Gas Piping Installation: Materials, Sizing Tables & Pressure Testing 10.4 OSHA Safety Standards: Fall Protection, Scaffolding, Ladders & HazCom 10.5 OSHA Heat Illness Prevention for Arizona Outdoor Work, LOTO & Arc Flash Safety

10.2 Refrigerant Copper Piping: ACR Tubing, Brazing with Nitrogen Purge & Trapping

Key Takeaways Explain This Topic AI

ACR copper tubing (ASTM B280) is dehydrated, nitrogen-purged, sealed with protective caps, and measured by Outside Diameter (OD), whereas plumbing copper (ASTM B88 Types K, L, M) is measured by Nominal Inside Diameter (ID = OD - 1/8 in.).

Brazing occurs above 840°F (typically 1,190°F to 1,500°F); AWS BCuP series (5%–15% silver) is self-fluxing on copper-to-copper, while BAg silver alloys require white fluoride flux when joining copper to brass, steel, or cast iron.

A continuous dry nitrogen purge at 1 to 3 SCFH (2 to 5 psig) during brazing is mandatory to displace atmospheric oxygen and eliminate internal black cupric oxide (Cu2O) scale formation that destroys TXVs and compressor oil pumps.

Suction risers require minimum vapor velocities of 1,000 to 1,500 FPM for positive oil return to the compressor crankcase, requiring P-traps at the base of vertical risers exceeding 8 feet and intermediate traps every 20 feet.

Liquid lines must maintain velocities of 100 to 300 FPM; vertical liquid risers experience a static pressure loss of ~0.5 psi per foot of lift, requiring sufficient system subcooling to prevent liquid flashing before the TXV.

Last updated: August 2026

Refrigerant Copper Piping, Brazing & Oil Management

Refrigerant piping in vapor-compression HVAC/R systems must fulfill two opposing fluid dynamic functions simultaneously: it must convey high-pressure liquid and low-pressure superheated vapor with minimal friction pressure drop (to preserve compressor capacity and system efficiency) while maintaining sufficient vapor velocity to continuously transport entrained lubricating oil (POE or PVE synthetic oils) through the circuit and back to the compressor crankcase.

Technicians in Arizona must understand the exact physical specifications of copper tubing, the thermodynamic and chemical requirements of high-temperature silver brazing under dry nitrogen, and the hydrodynamic engineering behind suction and liquid line sizing.

1. ACR Tubing vs. Plumbing Copper & Tube Tempers

Refrigerant piping requires strict metallurgical purity, cleanliness, and mechanical ductility that standard domestic water plumbing pipe cannot provide. +---------------------------------------------------------------------------------------------------+

  • | ACR COPPER VS. PLUMBING COPPER CLASSIFICATIONS |
  • +---------------------------------------------------------------------------------------------------+
  • | SPECIFICATION / PARAMETER | ACR COPPER TUBING (ASTM B280) | PLUMBING COPPER (ASTM B88) |
  • +-----------------------------+-----------------------------------+---------------------------------+
  • | Measurement Standard | Outside Diameter (OD) Actual Size | Nominal Inside Diameter (Nom ID)|
  • | Nominal vs. Actual Rule | 7/8 in. ACR = 7/8 in. Actual OD | 3/4 in. Nom. = 7/8 in. Actual OD|
  • | Internal Condition | Dehydrated, degreased, purged | May contain residual drawing oil|
  • | Sealing & Delivery | Factory pressurized & capped ends | Open, unsealed bundle ends |
  • | Alloy Grades Available | UNS C12200 (Phosphorized Copper) | Types K (Green), L (Blue), M(Red
  • | Wall Thickness Rank | Matches Type L (Rigid/Annealed) | K (Thickest) > L (Med) > M(Thin)|
  • +-----------------------------+-----------------------------------+---------------------------------+
  • The Sizing Distinction: OD vs. ID

ACR Copper Tubing (ASTM B280): Sized and designated strictly by its Outside Diameter (OD) . A piece of 3 / 4 inch 3/4\text{ inch} 3/4 inch ACR tubing measures exactly 0.750 inches 0.750\text{ inches} 0.750 inches on its outer surface.

Plumbing Copper Pipe (ASTM B88): Designated by its nominal internal diameter , which is approximately 1 / 8 inch 1/8\text{ inch} 1/8 inch smaller than its actual outside diameter: Plumbing Actual OD = Nominal ID + 1 8 inch = Nominal ID + 0.125 in \text{Plumbing Actual OD} = \text{Nominal ID} + \frac{1}{8}\text{ inch} = \text{Nominal ID} + 0.125\text{ in} Plumbing Actual OD = Nominal ID + 8 1 ​ inch = Nominal ID + 0.125 in

Critical Comparison: A 3 / 4 inch 3/4\text{ inch} 3/4 inch nominal Type L plumbing pipe has an actual OD of 7 / 8 inch 7/8\text{ inch} 7/8 inch ( 0.875 in 0.875\text{ in} 0.875 in ), making it physically identical in outside dimension to 7 / 8 inch 7/8\text{ inch} 7/8 inch ACR tubing.

Tube Tempers: Soft Annealed vs. Hard Drawn

Soft Annealed Copper: Thermally annealed at the factory to maximize ductility. Sold in 50 ft 50\text{ ft} 50 ft or 100 ft 100\text{ ft} 100 ft coiled rolls. Can be bent easily with mechanical lever benders and flared using 45 ∘ 45^\circ 4 5 ∘ flaring tools. Used primarily for underground linesets, mini-split connections, and compact residential runs. Has lower burst pressure than hard drawn copper of identical wall thickness.

Hard Drawn Copper: Cold-worked rigid straight lengths (typically 20 ft 20\text{ ft} 20 ft sticks). High tensile strength and rigid structural support. Cannot be bent with standard hand benders without kinking; directional changes require brazed wrought-copper elbows, tees, or swaged joints.

2. Brazing Metallurgy, Alloy Chemistry & Flux Protocols

Brazing is the primary method of joining refrigerant piping in split and commercial air conditioning systems. The American Welding Society (AWS) establishes the technical distinction between soldering and brazing:

Soldering: A joining process using filler metal with a liquidus temperature below 840 ∘ F 840^\circ\text{F} 84 0 ∘ F ( 450 ∘ C 450^\circ\text{C} 45 0 ∘ C ) without melting the base metals (e.g., 95 / 5 95/5 95/5 Tin-Antimony solder operating at 450 ∘ F– 464 ∘ F 450^\circ\text{F}\text{--}464^\circ\text{F} 45 0 ∘ F – 46 4 ∘ F ).

Brazing: A joining process using filler metal with a liquidus temperature above 840 ∘ F 840^\circ\text{F} 84 0 ∘ F ( 450 ∘ C 450^\circ\text{C} 45 0 ∘ C ) (typically operating between 1 , 190 ∘ F 1,190^\circ\text{F} 1 , 19 0 ∘ F and 1 , 500 ∘ F 1,500^\circ\text{F} 1 , 50 0 ∘ F ). +---------------------------------------------------------------------------------------------------+

  • | BRAZING FILLER METAL ALLOY COMPARISON |
  • +---------------------------------------------------------------------------------------------------+
  • | AWS ALLOY CLASS | CHEMICAL COMPOSITION | MELT / FLOW RANGE | FLUX REQUIREMENT |
  • +------------------+----------------------------------+-----------------------+---------------------+
  • | AWS BCuP-2 | 0% Ag, 7.0% P, 93.0% Cu | 1,310°F to 1,460°F | NO FLUX on Copper |
  • | AWS BCuP-3 | 5.0% Ag, 6.0% P, 89.0% Cu | 1,190°F to 1,495°F | NO FLUX on Copper |
  • | AWS BCuP-5 | 15.0% Ag, 5.0% P, 80.0% Cu | 1,190°F to 1,475°F | NO FLUX on Copper |
  • | AWS BAg-7 | 56.0% Ag, 22% Cu, 17% Zn, 5% Sn | 1,145°F to 1,205°F | WHITE FLUX MANDATORY|
  • | AWS BAg-24 | 50.0% Ag, 20% Cu, 28% Zn, 2% Ni | 1,220°F to 1,305°F | WHITE FLUX MANDATORY|
  • +------------------+----------------------------------+-----------------------+---------------------+
  • The Copper-Phosphorus Mechanism (BCuP Series)

The BCuP series of brazing alloys contains phosphorus ( 5 % to 7 % 5\%\text{ to }7\% 5% to 7% ). When heated in the presence of pure copper, phosphorus reacts with atmospheric and base-metal copper oxide to form copper phosphate glass, acting as a chemical self-fluxing agent .

Universal Rule: When brazing copper-to-copper joints using BCuP alloys (such as Sil-Fos 15 or Stay-Silv 5/15), chemical paste flux is strictly prohibited . Adding flux introduces acid residues that can enter the refrigeration loop.

Dissimilar Metals & Silver Alloys (BAg Series)

When joining copper tubing to brass valves, steel compressor stubs, bronze service ports, or cast iron :

The self-fluxing action of phosphorus does not work on non-copper metals.

Technicians must use a high-silver AWS BAg alloy ( 45 % to 56 % 45\%\text{ to }56\% 45% to 56% silver) and an approved AWS Type FB3-A white fluoride paste flux .

Application Rule: Paste flux must be applied sparingly only to the male tube insertion surface . Applying flux inside the female socket pushes surplus flux into the interior of the refrigerant pipe, where it reacts with POE synthetic lubricant to form hydrofluoric acid and sludge.

3. The Chemistry & Physics of Nitrogen Purging

When copper is heated above 800 ∘ F 800^\circ\text{F} 80 0 ∘ F ( 427 ∘ C 427^\circ\text{C} 42 7 ∘ C ) in the presence of atmospheric air (which contains ≈ 21 % \approx 21\% ≈ 21% oxygen), rapid chemical oxidation occurs on both the exterior and interior surfaces of the tubing: 4 Cu + O 2 → Δ > 800 ∘ F 2 Cu 2 O (Cuprous Oxide - Red/Black Scale) 4\text{Cu} + \text{O}_2 \xrightarrow{\Delta > 800^\circ\text{F}} 2\text{Cu}_2\text{O} \text{ (Cuprous Oxide - Red/Black Scale)} 4 Cu + O 2 ​ Δ > 80 0 ∘ F ​ 2 Cu 2 ​ O (Cuprous Oxide - Red/Black Scale) 2 Cu 2 O + O 2 → Δ 4 CuO (Cupric Oxide - Black Flaking Scale) 2\text{Cu}_2\text{O} + \text{O}_2 \xrightarrow{\Delta} 4\text{CuO} \text{ (Cupric Oxide - Black Flaking Scale)} 2 Cu 2 ​ O + O 2 ​ Δ ​ 4 CuO (Cupric Oxide - Black Flaking Scale) +---------------------------------------------------------------------------------------------------+

  • | CONSEQUENCES OF BRAZING WITHOUT DRY NITROGEN PURGE |
  • +---------------------------------------------------------------------------------------------------+
  • | SYSTEM COMPONENT | FAILURE MECHANISM INDUCED BY COPPER OXIDE SCALE |
  • +-----------------------------+---------------------------------------------------------------------+
  • | Thermal Expansion Valve | Scale flakes lodge in 0.020 in. metering orifice, causing starve/jam|
  • | Liquid Line Filter-Drier | Drier core clogs with black soot, creating high pressure drop (ΔP) |
  • | Compressor Crankcase | POE oil strips scale off walls; abrasive slurry grinds bearings |
  • | Reversing Valve (Heat Pump)| Scale scratches slide valve Teflon seals, causing bypass leakage |
  • | Compressor Oil Pump Screen | Suction inlet screen blinds over, starving pump and throwing rods |
  • +-----------------------------+-----------------------------------+---------------------------------+
  • Nitrogen Purging Field Protocol

To completely eliminate oxidation, an inert shield of Dry Nitrogen must flow through the tubing assembly during the entire brazing operation:

Flow Rate & Pressure: Connect a nitrogen cylinder equipped with a high-accuracy flowmeter or two-stage regulator. Regulate flow to 1 to 3 SCFH 1\text{ to }3\text{ SCFH} 1 to 3 SCFH (Standard Cubic Feet per Hour) , which equates to approximately 2 to 5 psig 2\text{ to }5\text{ psig} 2 to 5 psig of line pressure.

Atmospheric Displacement: The nitrogen flow must be established before torch heat is applied to displace all trapped air. A slight whisper of gas should be felt at the exit port.

Continuous Purge: Maintain flow throughout heating and brazing until the joint has cooled below 600 ∘ F 600^\circ\text{F} 60 0 ∘ F (dark cherry red heat completely dissipated).

Never Braze a Sealed Loop: Always provide an open exit relief port (such as an open Schrader valve with core removed). Brazing a closed pipe creates thermal pressure expansion that blows molten alloy out of the joint socket, creating microscopic pinholes.

4. Hydrodynamic Line Sizing & Oil Return Dynamics

Refrigerant oil (mineral, alkylbenzene, or polyolester/POE) continuously circulates through the refrigeration system. Because oil mixes with liquid refrigerant in the condenser but separates as refrigerant evaporates into vapor in the evaporator, the suction line vapor must travel at sufficient velocity to drag oil droplets upward against gravity. +---------------------------------------------------------------------------------------------------+

  • | REFRIGERANT LINE VELOCITY DESIGN BOUNDARIES |
  • +---------------------------------------------------------------------------------------------------+
  • | LINE APPLICATION | MINIMUM VELOCITY (OIL RETURN) | MAXIMUM VELOCITY (NOISE/EROSION)|
  • +-----------------------------+-----------------------------------+---------------------------------+
  • | Horizontal Suction Line | 500 to 700 FPM (2.5 to 3.5 m/s) | 2,000 to 2,500 FPM (12.7 m/s) |
  • | Vertical Suction Riser | 1,000 to 1,500 FPM (5.1 to 7.6 m/s)| 3,000 to 4,000 FPM (20.3 m/s) |
  • | Discharge (Hot Gas) Line | 500 FPM (Horizontal) / 1,000 FPM | 3,500 FPM (17.8 m/s) |
  • | Liquid Line | N/A (Liquid miscible with oil) | 100 to 300 FPM (1.5 m/s Max) |
  • +-----------------------------+-----------------------------------+---------------------------------+
  • Suction Line Trapping Principles

Horizontal Pitch: Horizontal suction piping must slope downward in the direction of refrigerant flow toward the compressor at a minimum rate of 1 / 2 inch 1/2\text{ inch} 1/2 inch per 10 feet 10\text{ feet} 10 feet of run ( 1 / 4 in. per 10 ft 1/4\text{ in. per }10\text{ ft} 1/4 in. per 10 ft absolute minimum) to allow gravity to assist oil movement.

P-Trap at Riser Base: Whenever an evaporator is located below the compressor, an oil trap (P-trap) must be installed at the base of any vertical suction riser exceeding 8 feet 8\text{ feet} 8 feet in height .

Intermediate Traps: In tall vertical suction risers, intermediate P-traps must be installed every 20 feet 20\text{ feet} 20 feet of vertical elevation .

Inverted Trap (Gooseneck): An inverted P-trap must be installed at the top of the vertical riser before tying into the horizontal main. This prevents oil collected in the horizontal run from draining back into the evaporator coil during off-cycle periods. VERTICAL SUCTION RISER TRAPPING

  • Horizontal Line to Compressor (Sloped 1/2" per 10')
  • ▲
  • │ ┌─────────┐
  • └─┘ Inverted│ Inverted Top Trap (Gooseneck)
  • Trap │ (Prevents off-cycle oil drainage)
  • │
  • │
  • │ Vertical Riser Height
  • │ (Max 20 ft between traps)
  • │ Vapor Velocity ≥ 1,200 FPM
  • │
  • │
  • │
  • Evaporator Outlet ───────────────┘
  • │ ┌───┐
  • └───────────────────────┘ P ├─── P-Trap at Base of Riser
  • Trap (Captures oil droplet slug)
  • Liquid Line Sizing & Vertical Static Head Loss

Liquid lines must be sized to prevent excessive pressure drop that causes liquid refrigerant to boil prematurely before entering the expansion device—a destructive condition known as flash gas .

Static Pressure Loss in Liquid Risers: When liquid refrigerant travels vertically upward, it loses static head pressure due to the physical weight of the liquid column. For R-410A and R-22, this static head loss equals approximately: Δ P static ≈ 0.50 psi per vertical foot of lift \Delta P_{\text{static}} \approx 0.50\text{ psi per vertical foot of lift} Δ P static ​ ≈ 0.50 psi per vertical foot of lift

Subcooling Requirement: If an outdoor condenser sits 30 feet 30\text{ feet} 30 feet below a rooftop evaporator coil, the static head loss alone is: Δ P head = 30 ft × 0.50 psi ft = 15.0 psi \Delta P_{\text{head}} = 30\text{ ft} \times 0.50\frac{\text{psi}}{\text{ft}} = 15.0\text{ psi} Δ P head ​ = 30 ft × 0.50 ft psi ​ = 15.0 psi Adding 5.0 psi 5.0\text{ psi} 5.0 psi of piping friction yields a total pressure drop of 20.0 psi 20.0\text{ psi} 20.0 psi . Technicians must ensure the condensing unit provides enough liquid subcooling (typically 10 ∘ F to 15 ∘ F 10^\circ\text{F}\text{ to }15^\circ\text{F} 1 0 ∘ F to 1 5 ∘ F ) so that saturation pressure is never reached before the TXV inlet.

Loading diagram... Nitrogen Purge Setup & Vertical Refrigerant Riser Trapping Architecture