Study guide

3.2 Recovery, Recycling & Reclaim Standards, Evacuation Levels & Deep Vacuum Procedures

Arizona HVAC Contractor License ROC R-39R/C-39/CR-39

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Arizona ROC Licensing & Legal Framework

1.1 Arizona ROC Authority & License Classifications 1.2 Application Requirements, Qualifying Party Duties & Experience Standards 1.3 Contractor Bonds, Financial Requirements & Residential Recovery Fund 1.4 Arizona Prompt Pay Act, Contracting Requirements & Mechanic's Liens 1.5 ROC Workmanship Standards, Complaint Investigation, Citations & Disciplinary Procedures

2 Chapter 2: Thermodynamics & The Vapor Compression Refrigeration Cycle

2.1 Thermodynamic Fundamentals, Heat Transfer & Pressure-Temperature Relationships 2.2 The Four Primary Cycle Components: Compressors, Condensers, Metering Devices & Evaporators 2.3 Superheat & Subcooling: Measurement, Calculation & Diagnostic Interpretation 2.4 Pressure-Enthalpy (P-h) Diagrams & System Operating Analysis 2.5 Refrigerant Characteristics, Oil Miscibility & ASHRAE Safety Classifications

3 Chapter 3: Refrigerant Management, EPA Section 608 & Environmental Compliance

3.1 EPA Clean Air Act Section 608 Regulations, Certifications & Venting Prohibitions 3.2 Recovery, Recycling & Reclaim Standards, Evacuation Levels & Deep Vacuum Procedures 3.3 Leak Detection Methods & Mandatory Repair Trigger Rates 3.4 Low-GWP Refrigerants & A2L Transition Safety Requirements 3.5 System Evacuation, Triple Evacuation Method, Vacuum Decay Testing & Moisture Removal

4 Chapter 4: Heating Systems: Gas Furnaces, Electric Heat & Combustion Safety

4.1 Fuel Gas Combustion Chemistry, Gas Burners & Orifice Sizing 4.2 Gas Furnace Components, Ignition Systems & Flame Rectification 4.3 Furnace Safety Controls & Troubleshooting Sequences 4.4 Gas Venting Categories (I-IV), Vent Sizing & Combustion Air Calculations 4.5 Electric Furnaces & Duct Heaters: Sizing, Sequencers, Thermal Cutoffs & Wiring

5 Chapter 5: Heat Pump Systems & Defrost Operation

5.1 Heat Pump Operating Principles & Reversing Valve Operation 5.2 Thermal Expansion Valves (TXVs), Electronic Expansion Valves (EEVs) & Bi-flow Metering 5.3 Defrost Systems: Time-Temperature vs. Demand Defrost Cycles & Sensor Operation 5.4 Heat Pump Balance Point Analysis, Supplemental Strip Heat Staging & Emergency Heat 5.5 Inverter-Driven Variable Capacity Systems & Desert Heat Pump Performance

6 Chapter 6: Air Distribution, Duct Design & Airflow Dynamics

6.1 Airflow Fundamentals: CFM Requirements, Velocity, Static Pressure & TESP 6.2 ACCA Manual D Duct Sizing: Equal Friction Method & Friction Rate Calculations 6.3 Duct Construction, Materials & SMACNA Support Standards 6.4 Duct Sealing (UL 181 Standards, Mastic, Tapes), Attic Insulation & Leakage Testing 6.5 Air System Balancing, Diagnostic Instruments & Grille/Register Selection

7 Chapter 7: Psychrometrics & Desert Climate HVAC Load Sizing

7.1 The Psychrometric Chart: Dry-Bulb, Wet-Bulb, Relative Humidity, Enthalpy & Dew Point 7.2 Psychrometric Air Conditioning Processes: Cooling, Heating, Humidification & Dehumidification 7.3 ACCA Manual J Residential Load Calculations: Heat Gain, Heat Loss, U-Values & SHGC 7.4 Arizona Desert Climate Design Considerations: Sensible Heat Ratios & Manual S Sizing 7.5 Evaporative Cooling Systems (Direct & Indirect Swamp Coolers): Principles & Maintenance

8 Chapter 8: HVAC Electrical Systems, Motors & Control Circuits

8.1 Electrical Fundamentals for HVAC: Ohm's Law, Power Formula & Single/Three-Phase Power 8.2 24VAC Control Circuits, Step-Down Transformers, Relays & Contactors 8.3 Capacitors (Start & Run), Potential Relays & Motor Starting Circuits 8.4 HVAC Motors: PSC, ECM & Three-Phase Motors 8.5 NEC Article 440 Compliance: MCA, MOCP & Disconnect Switch Rules

9 Chapter 9: Hydronics, Boilers, Chilled Water & Commercial Systems

9.1 Hydronic Heating Systems: Low-Pressure Hot Water & Steam Boilers 9.2 Hydronic Specialties: Air Separators, Expansion Tanks, Circulator Pumps & Zone Valves 9.3 Water Piping Systems, Sizing, Flow Rates & Relief Valves 9.4 Commercial Chilled Water Systems: Air-Cooled & Water-Cooled Chillers 9.5 Cooling Towers, Condenser Water Loops & Legionella Water Treatment

10 Chapter 10: Codes, Piping Systems, Safety & OSHA Standards

10.1 International Mechanical Code (IMC) & International Fuel Gas Code (IFGC) Compliance 10.2 Refrigerant Copper Piping: ACR Tubing, Brazing with Nitrogen Purge & Trapping 10.3 Fuel Gas Piping Installation: Materials, Sizing Tables & Pressure Testing 10.4 OSHA Safety Standards: Fall Protection, Scaffolding, Ladders & HazCom 10.5 OSHA Heat Illness Prevention for Arizona Outdoor Work, LOTO & Arc Flash Safety

3.2 Recovery, Recycling & Reclaim Standards, Evacuation Levels & Deep Vacuum Procedures

Key Takeaways Explain This Topic AI

Under AHRI Standard 700, 'Recover' means removing refrigerant to an external cylinder, 'Recycle' means cleaning it via oil separation and filter driers for reuse by the same owner, and 'Reclaim' means chemical reprocessing to virgin specifications verified by laboratory gas chromatography.

System-dependent (passive) recovery relies on appliance pressure or compressor operation and is restricted to appliances containing ≤ 15 lbs of refrigerant; self-contained (active) recovery uses an independent compressor.

Under 40 CFR 82.156 Table 1 the required evacuation level depends on the appliance pressure class and charge size, not the refrigerant brand: high-pressure appliances (such as R-22, R-407C, R-410A) under 200 lb require only 0 inches Hg; high-pressure appliances at 200 lb or more and medium-pressure appliances (such as R-12, R-134a) under 200 lb require 10 inches Hg; medium-pressure appliances at 200 lb or more require 15 inches Hg; and low-pressure appliances require 25 mm Hg absolute.

DOT recovery cylinders (gray body with safety yellow top) must never be filled beyond 80% liquid capacity at 77°F, calculated as (WC × SG × 0.80) + Tare Weight.

DOT recovery cylinders must undergo hydrostatic pressure retesting and recertification every 5 years.

Last updated: October 2026

The Three R's: Recover, Recycle, and Reclaim

The EPA and the Air-Conditioning, Heating, and Refrigeration Institute (AHRI) establish strict definitions for the three fundamental refrigerant management processes. Technicians and licensed HVAC contractors must distinguish between these three distinct tiers of processing: +---------------------------------------------------------------------------------------------------+

  • | THE THREE R'S (EPA & AHRI DEFINITIONS) |
  • +---------------------------------------------------------------------------------------------------+
  • | 1. RECOVER |
  • | - Definition: To remove refrigerant in any condition from an appliance and store it in an |
  • | external container without necessarily testing or processing it in any way. |
  • | - Application: Standard field procedure prior to opening any refrigeration circuit for service. |
  • +---------------------------------------------------------------------------------------------------+
  • | 2. RECYCLE |
  • | - Definition: To extract refrigerant from an appliance and clean it for reuse by separating |
  • | lubricating oil and passing it through single or multiple replaceable-core filter driers to |
  • | reduce moisture, acidity, and particulate matter. |
  • | - Ownership Rule: Recycled refrigerant may ONLY be returned to the original appliance or to |
  • | another appliance owned by the EXACT SAME customer/entity. It CANNOT be sold to another owner. |
  • +---------------------------------------------------------------------------------------------------+
  • | 3. RECLAIM |
  • | - Definition: To reprocess used refrigerant to new product chemical specifications that match |
  • | AHRI Standard 700, verified through rigorous laboratory chemical analysis (gas chromatography).|
  • | - Resale Rule: Only reclaimed refrigerant certified by an EPA-certified reclamation facility may |
  • | be sold on the open market or transferred to different equipment owners. |
  • +---------------------------------------------------------------------------------------------------+
  • Recovery Equipment Types: Active vs. Passive

EPA regulations categorize recovery equipment based on its operating mechanism:

1. Self-Contained (Active) Recovery Equipment

Operating Principle: Contains its own onboard hermetic or semi-hermetic compressor, electric motor, condenser coil, and oil separator.

Function: Draws refrigerant vapor/liquid out of the appliance independently of the appliance's operating state or compressor.

Requirement: Mandatory for all field servicing on systems containing more than 15 lbs of refrigerant and all standard commercial/residential field service.

2. System-Dependent (Passive) Recovery Equipment

Operating Principle: Lacks an internal mechanical compressor. Relies entirely on the appliance's internal compressor, the natural pressure difference of the refrigerant, or external heat application (heating the evaporator/coils) to drive refrigerant vapor into an unpressurized or evacuated container/recovery bag.

Limitations: EPA regulations restrict system-dependent recovery strictly to small appliances containing 15 lbs or less of refrigerant (Type I).

Mandatory EPA Evacuation Levels (40 CFR § 82.156, Table 1)

Before opening a refrigeration circuit, technicians must evacuate to the level in Table 1 of 40 CFR § 82.156 . The table is organized by the appliance's pressure class and full charge , not by refrigerant trade name, and the vacuum figures are inches of Hg vacuum relative to standard atmospheric pressure of 29.9 inches Hg :

Type of Appliance (Table 1 category) Equipment made BEFORE Nov 15, 1993 Equipment made ON OR AFTER Nov 15, 1993

  • Very high-pressure appliance (R-13, R-23, R-503) 0 0
  • High-pressure appliance, or isolated component, full charge less than 200 lb 0 0
  • High-pressure appliance, or isolated component, full charge 200 lb or more 4 10
  • Medium-pressure appliance, or isolated component, full charge less than 200 lb 4 10
  • Medium-pressure appliance, or isolated component, full charge 200 lb or more 4 15
  • Low-pressure appliance (R-11, R-123, R-113) 25 mm Hg absolute 25 mm Hg absolute
  • Reading the Table Correctly

High-pressure appliance means one using a refrigerant with a liquid-phase saturation pressure between 170 and 355 psia at 104 °F (40 CFR 82.152) — EPA's examples are R-22, R-407A, R-407C, R-410A and R-502. Medium-pressure appliance means 45 to 170 psia at 104 °F (R-12, R-114, R-124, R-134a, R-500). Very high-pressure is above 355 psia or a critical temperature below 104 °F (R-13, R-23, R-503); low-pressure is below 45 psia (R-11, R-113, R-123, R-245fa).

Exam Trap: Nearly all field HVAC work — residential splits, heat pumps, rooftop units, walk-ins — is a high-pressure appliance with well under 200 lb of charge , so the required level under Table 1 is 0 inches Hg (0 psig) , not 10 inches. The 10-inch requirement kicks in only at 200 lb or more of a high-pressure refrigerant, or on a medium-pressure appliance under 200 lb.

Non-major service (§ 82.156(a)(1)): Where the appliance will not be evacuated to atmosphere afterward and the work is not a major repair, a medium-, high- or very high-pressure appliance need only be evacuated to no higher than 0 psig ; a low-pressure appliance is pressurized to no higher than 0 psig; and for oil changes, 5 psig.

Leaking appliances (§ 82.156(a)(2)): Where leaks make Table 1 levels unattainable or would substantially contaminate the recovered refrigerant, isolate leaking from non-leaking components, evacuate the non-leaking components to Table 1 levels, and evacuate the leaking components to the lowest attainable level — which may not exceed 0 psig .

Definition of Major Repair: Under 40 CFR § 82.152, "major maintenance, service, or repair" means service involving the removal of the appliance's compressor, condenser, evaporator, or auxiliary heat exchanger coil .

Recovery Cylinder DOT Safety Standards & 80% Fill Limit Rule

Department of Transportation ( DOT 4BA or DOT 4BW ) certified recovery cylinders are engineered specifically for pressurized refrigerant handling:

Color Code Standard: Yellow top/collar and shoulder, with an industrial gray body.

Hydrostatic Retest Schedule: Must be hydrostatically pressure tested and date-stamped every 5 years .

Pressure Relief Setting: Equipped with a mechanical spring-loaded relief valve typically set to 600 psig for R-410A rated tanks (400 psig for older R-22 rated tanks). +---------------------------------------------------------------------------------------------------+

  • | RECOVERY CYLINDER COLOR & SAFETY CODES |
  • +---------------------------------------------------------------------------------------------------+
  • | [ YELLOW TOP / COLLAR & SHOULDER ] <--- Identifies Recovery Tank (DOT 4BA/4BW) |
  • | +--------------------------------+ |
  • | | | |
  • | | GRAY BODY CASING | <--- 80% Maximum Liquid Capacity at 77°F |
  • | | | <--- Hydrostatic Retest Required Every 5 Years |
  • | | | |
  • | +--------------------------------+ |
  • +---------------------------------------------------------------------------------------------------+
  • The 80% Liquid Fill Calculation Formula

Refrigerant liquids expand dramatically when exposed to ambient temperature increases. To prevent hydrostatic liquid lock (which causes catastrophic cylinder rupture), cylinders must never be filled beyond 80% of their total liquid volume at 77°F (25°C). Maximum Gross Weight (lbs) = ( WC × SG × 0.80 ) + TW \text{Maximum Gross Weight (lbs)} = (\text{WC} \times \text{SG} \times 0.80) + \text{TW} Maximum Gross Weight (lbs) = ( WC × SG × 0.80 ) + TW

Where:

WC \text{WC} WC = Water Capacity stamped on cylinder collar (pounds of water cylinder can hold)

SG \text{SG} SG = Specific Gravity of the refrigerant liquid at 77°F (from AHRI tables; e.g., R-22 = 1.19, R-410A = 1.06, R-134a = 1.20)

  • 0.80 0.80 0.80 = 80% maximum legal liquid volume safety coefficient
  • TW \text{TW} TW = Tare Weight (empty weight of cylinder and dual valve assembly stamped on collar)
  • Step-by-Step Worked Calculation Example

Problem: A technician is recovering R-410A ( S G = 1.06 SG = 1.06 SG = 1.06 ) into a DOT recovery cylinder. The cylinder collar has the following stamped specifications:

  • WC = 47.6 lbs \text{WC} = 47.6\text{ lbs} WC = 47.6 lbs
  • TW = 28.2 lbs \text{TW} = 28.2\text{ lbs} TW = 28.2 lbs

Calculate the maximum allowable gross scale weight before recovery must be stopped. Net Max Refrigerant Weight = 47.6 × 1.06 × 0.80 = 50.456 × 0.80 = 40.36 lbs \text{Net Max Refrigerant Weight} = 47.6 \times 1.06 \times 0.80 = 50.456 \times 0.80 = 40.36\text{ lbs} Net Max Refrigerant Weight = 47.6 × 1.06 × 0.80 = 50.456 × 0.80 = 40.36 lbs Maximum Gross Scale Weight = 40.36 lbs + 28.2 lbs (TW) = 68.56 lbs \text{Maximum Gross Scale Weight} = 40.36\text{ lbs} + 28.2\text{ lbs (TW)} = \mathbf{68.56\text{ lbs}} Maximum Gross Scale Weight = 40.36 lbs + 28.2 lbs (TW) = 68.56 lbs

Result: The recovery process must be terminated when the scale reaches 68.56 lbs (or approx. 68.5 lbs).

Exam Trap: Never combine different types of refrigerants into a single recovery cylinder. Mixed refrigerants cannot be separated by standard fractional distillation at reclamation facilities and must be shipped to hazardous waste thermal incinerators at extraordinary expense to the contractor.