Study guide

5.4 Heat Pump Balance Point Analysis, Supplemental Strip Heat Staging & Emergency Heat

Arizona HVAC Contractor License ROC R-39R/C-39/CR-39

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Arizona ROC Licensing & Legal Framework

1.1 Arizona ROC Authority & License Classifications 1.2 Application Requirements, Qualifying Party Duties & Experience Standards 1.3 Contractor Bonds, Financial Requirements & Residential Recovery Fund 1.4 Arizona Prompt Pay Act, Contracting Requirements & Mechanic's Liens 1.5 ROC Workmanship Standards, Complaint Investigation, Citations & Disciplinary Procedures

2 Chapter 2: Thermodynamics & The Vapor Compression Refrigeration Cycle

2.1 Thermodynamic Fundamentals, Heat Transfer & Pressure-Temperature Relationships 2.2 The Four Primary Cycle Components: Compressors, Condensers, Metering Devices & Evaporators 2.3 Superheat & Subcooling: Measurement, Calculation & Diagnostic Interpretation 2.4 Pressure-Enthalpy (P-h) Diagrams & System Operating Analysis 2.5 Refrigerant Characteristics, Oil Miscibility & ASHRAE Safety Classifications

3 Chapter 3: Refrigerant Management, EPA Section 608 & Environmental Compliance

3.1 EPA Clean Air Act Section 608 Regulations, Certifications & Venting Prohibitions 3.2 Recovery, Recycling & Reclaim Standards, Evacuation Levels & Deep Vacuum Procedures 3.3 Leak Detection Methods & Mandatory Repair Trigger Rates 3.4 Low-GWP Refrigerants & A2L Transition Safety Requirements 3.5 System Evacuation, Triple Evacuation Method, Vacuum Decay Testing & Moisture Removal

4 Chapter 4: Heating Systems: Gas Furnaces, Electric Heat & Combustion Safety

4.1 Fuel Gas Combustion Chemistry, Gas Burners & Orifice Sizing 4.2 Gas Furnace Components, Ignition Systems & Flame Rectification 4.3 Furnace Safety Controls & Troubleshooting Sequences 4.4 Gas Venting Categories (I-IV), Vent Sizing & Combustion Air Calculations 4.5 Electric Furnaces & Duct Heaters: Sizing, Sequencers, Thermal Cutoffs & Wiring

5 Chapter 5: Heat Pump Systems & Defrost Operation

5.1 Heat Pump Operating Principles & Reversing Valve Operation 5.2 Thermal Expansion Valves (TXVs), Electronic Expansion Valves (EEVs) & Bi-flow Metering 5.3 Defrost Systems: Time-Temperature vs. Demand Defrost Cycles & Sensor Operation 5.4 Heat Pump Balance Point Analysis, Supplemental Strip Heat Staging & Emergency Heat 5.5 Inverter-Driven Variable Capacity Systems & Desert Heat Pump Performance

6 Chapter 6: Air Distribution, Duct Design & Airflow Dynamics

6.1 Airflow Fundamentals: CFM Requirements, Velocity, Static Pressure & TESP 6.2 ACCA Manual D Duct Sizing: Equal Friction Method & Friction Rate Calculations 6.3 Duct Construction, Materials & SMACNA Support Standards 6.4 Duct Sealing (UL 181 Standards, Mastic, Tapes), Attic Insulation & Leakage Testing 6.5 Air System Balancing, Diagnostic Instruments & Grille/Register Selection

7 Chapter 7: Psychrometrics & Desert Climate HVAC Load Sizing

7.1 The Psychrometric Chart: Dry-Bulb, Wet-Bulb, Relative Humidity, Enthalpy & Dew Point 7.2 Psychrometric Air Conditioning Processes: Cooling, Heating, Humidification & Dehumidification 7.3 ACCA Manual J Residential Load Calculations: Heat Gain, Heat Loss, U-Values & SHGC 7.4 Arizona Desert Climate Design Considerations: Sensible Heat Ratios & Manual S Sizing 7.5 Evaporative Cooling Systems (Direct & Indirect Swamp Coolers): Principles & Maintenance

8 Chapter 8: HVAC Electrical Systems, Motors & Control Circuits

8.1 Electrical Fundamentals for HVAC: Ohm's Law, Power Formula & Single/Three-Phase Power 8.2 24VAC Control Circuits, Step-Down Transformers, Relays & Contactors 8.3 Capacitors (Start & Run), Potential Relays & Motor Starting Circuits 8.4 HVAC Motors: PSC, ECM & Three-Phase Motors 8.5 NEC Article 440 Compliance: MCA, MOCP & Disconnect Switch Rules

9 Chapter 9: Hydronics, Boilers, Chilled Water & Commercial Systems

9.1 Hydronic Heating Systems: Low-Pressure Hot Water & Steam Boilers 9.2 Hydronic Specialties: Air Separators, Expansion Tanks, Circulator Pumps & Zone Valves 9.3 Water Piping Systems, Sizing, Flow Rates & Relief Valves 9.4 Commercial Chilled Water Systems: Air-Cooled & Water-Cooled Chillers 9.5 Cooling Towers, Condenser Water Loops & Legionella Water Treatment

10 Chapter 10: Codes, Piping Systems, Safety & OSHA Standards

10.1 International Mechanical Code (IMC) & International Fuel Gas Code (IFGC) Compliance 10.2 Refrigerant Copper Piping: ACR Tubing, Brazing with Nitrogen Purge & Trapping 10.3 Fuel Gas Piping Installation: Materials, Sizing Tables & Pressure Testing 10.4 OSHA Safety Standards: Fall Protection, Scaffolding, Ladders & HazCom 10.5 OSHA Heat Illness Prevention for Arizona Outdoor Work, LOTO & Arc Flash Safety

5.4 Heat Pump Balance Point Analysis, Supplemental Strip Heat Staging & Emergency Heat

Key Takeaways Explain This Topic AI

The thermal balance point is the exact outdoor ambient temperature where the structure's heat loss equals the heat pump's maximum heating capacity without auxiliary heat.

The economic balance point is the outdoor ambient temperature where the operating cost per delivered BTU of heat pump heating equals the cost of auxiliary heating fuels (gas, propane, or electric strip).

Supplemental electric resistance strip heat is staged using outdoor thermostats (OT-1, OT-2) set at and below the balance point to prevent high-kW electric heaters from energizing when the heat pump can carry the load alone.

Emergency Heat ('E' terminal) locks out the heat pump compressor entirely, powering 100% supplemental heat to provide comfort during mechanical compressor failure or refrigerant loss.

Last updated: August 2026

5.4 Heat Pump Balance Point Analysis, Supplemental Strip Heat Staging & Emergency Heat

Because the heating output of an air-source heat pump declines as outdoor ambient temperature drops—while the building's heating load simultaneously increases—every heat pump installation exhibits a specific temperature crossover known as the balance point . Sizing supplemental heating equipment, staging electric strip heat with outdoor thermostats, and understanding emergency heat controls are critical competencies tested on the Arizona HVAC Contractor License Exam.

1. Thermal Balance Point Analysis & Graphical Determination

The thermal balance point is defined as the outdoor ambient temperature at which the heat pump's heating capacity exactly matches the total building heat loss without any supplemental heat assistance. THERMAL BALANCE POINT GRAPH

  • Heating Capacity / Load (BTU/hr)
  • ▲
  • │ Building Heat Loss Line
  • │ / (Heating Deficit - Requires (Slopes UP as temp drops)
  • 50k│ / Supplemental Strip Heat) /
  • │/ /
  • 40k│\ /
  • │ \ /
  • 30k│ \ /
  • │ \◄─── THERMAL BALANCE POINT ────X
  • 20k│ \ (e.g., 32°F Ambient) / \
  • │ \ / \ Heat Pump Capacity Line
  • 10k│ \ / \ (Slopes DOWN as temp drops)
  • │ \ / \
  • 0 └────────┴───────────┴─────────┴─────────┴──────────► Outdoor Temp (°F)
  • 0°F 15°F 30°F 45°F 65°F
  • Mathematical Formulation

Building Heat Loss Line: Calculated according to ACCA Manual J. Heat loss increases linearly as outdoor temperature drops below the indoor setpoint ( T indoor T_{\text{indoor}} T indoor ​ , typically 70°F): Heat Loss (BTU/hr) = Design Heat Loss × ( T indoor − T outdoor T indoor − T design ) \text{Heat Loss (BTU/hr)} = \text{Design Heat Loss} \times \left(\frac{T_{\text{indoor}} - T_{\text{outdoor}}}{T_{\text{indoor}} - T_{\text{design}}}\right) Heat Loss (BTU/hr) = Design Heat Loss × ( T indoor ​ − T design ​ T indoor ​ − T outdoor ​ ​ )

Heat Pump Heating Capacity Curve: Published in manufacturer expanded heating tables (AHRI ratings at 47°F and 17°F). Capacity decreases as ambient drops.

Balance Point Determination: The intersection of the Heat Loss line and the Heat Pump Capacity curve defines the thermal balance point (typically between 28°F and 38°F for properly sized residential systems in Arizona).

Above Balance Point: Heat pump capacity exceeds building heat loss. The heat pump cycles or modulates to satisfy the thermostat; auxiliary heat is not required.

Below Balance Point: Building heat loss exceeds heat pump capacity. The heat pump runs continuously, and supplemental heat must energize to make up the heating deficit.

2. Economic Balance Point Calculations

The economic balance point is the outdoor temperature at which the cost to operate the heat pump per delivered BTU equals the cost of operating an auxiliary heating system (such as a natural gas furnace, propane burner, or electric resistance strip):

Formulas for Heating Fuel Cost per 100,000 BTU (1 Therm)

Electric Resistance Heat ( COP = 1.0 \text{COP} = 1.0 COP = 1.0 ): Cost electric strip = ( 100 , 000 BTU 3 , 412 BTU/kWh ) × Electric Rate ($/kWh) = 29.308 × Rate elec \text{Cost}_{\text{electric strip}} = \left(\frac{100,000\text{ BTU}}{3,412\text{ BTU/kWh}}\right) \times \text{Electric Rate (\$/kWh)} = 29.308 \times \text{Rate}_{\text{elec}} Cost electric strip ​ = ( 3 , 412 BTU/kWh 100 , 000 BTU ​ ) × Electric Rate ($/kWh) = 29.308 × Rate elec ​

Heat Pump ( C O P > 1.0 COP > 1.0 COP > 1.0 ): Cost heat pump = ( 100 , 000 BTU COP × 3 , 412 BTU/kWh ) × Rate elec = 29.308 × Rate elec COP \text{Cost}_{\text{heat pump}} = \left(\frac{100,000\text{ BTU}}{\text{COP} \times 3,412\text{ BTU/kWh}}\right) \times \text{Rate}_{\text{elec}} = \frac{29.308 \times \text{Rate}_{\text{elec}}}{\text{COP}} Cost heat pump ​ = ( COP × 3 , 412 BTU/kWh 100 , 000 BTU ​ ) × Rate elec ​ = COP 29.308 × Rate elec ​ ​

Natural Gas Furnace (AFUE %): Cost gas furnace = Gas Rate ($/Therm) AFUE \text{Cost}_{\text{gas furnace}} = \frac{\text{Gas Rate (\$/Therm)}}{\text{AFUE}} Cost gas furnace ​ = AFUE Gas Rate ($/Therm) ​

Economic Crossover Formula

Equating Heat Pump Cost to Gas Furnace Cost yields the critical COP where both systems cost the exact same to operate: COP economic crossover = 29.308 × Rate elec ( $ / kWh ) Gas Rate ($/Therm) AFUE \text{COP}_{\text{economic crossover}} = \frac{29.308 \times \text{Rate}_{\text{elec}} (\$/\text{kWh})}{\frac{\text{Gas Rate (\$/Therm)}}{\text{AFUE}}} COP economic crossover ​ = AFUE Gas Rate ($/Therm) ​ 29.308 × Rate elec ​ ( $/ kWh ) ​

When outdoor temperatures drop to the point where the heat pump's operating COP falls below COP economic crossover \text{COP}_{\text{economic crossover}} COP economic crossover ​ , it becomes cheaper to shut off the heat pump and run the gas furnace exclusively.

3. Supplemental Electric Strip Heat Staging & Outdoor Thermostats

Supplemental electric resistance heating elements (open nichrome wire coils) are installed in the indoor air handler or supply duct plenum. Each kilowatt (kW) of electric heat generates 3,412 BTU/hr of sensible heat: Heating Output (BTU/hr) = kW × 3 , 412 \text{Heating Output (BTU/hr)} = \text{kW} \times 3,412 Heating Output (BTU/hr) = kW × 3 , 412 SUPPLEMENTAL HEAT STAGING WITH OUTDOOR THERMOSTATS

  • Thermostat Call for Heat (W1 / Y) ──► Compressor Runs Continuously
  • │
  • Room Temp Drops 1.5°F Below Setpoint ──► Thermostat Closes 2nd Stage (W2)
  • │
  • ┌────────────────────┴────────────────────┐
  • ▼ ▼
  • [ Outdoor Thermostat OT-1 ] [ Outdoor Thermostat OT-2 ]
  • Set at Balance Point Set 7°F Below Balance Point
  • (e.g., Closes at ≤32°F) (e.g., Closes at ≤25°F)
  • │ │
  • ▼ ▼
  • Bank 1 Strip Heat (5 kW) Bank 2 Strip Heat (5 kW)
  • Outdoor Thermostat (OT) Functions & Code Rules

Preventing Unnecessary Electric Demand: In mild winter weather (45°F to 60°F), if a homeowner raises the thermostat setpoint by 3°F, a standard two-stage thermostat would call for 2nd stage heat (W2), energizing 10 kW to 15 kW of strip heat (34,120 to 51,180 BTU/hr). This causes severe electric utility demand spikes and high power bills.

Outdoor Thermostat Staging:

OT-1: Wired in series with the first bank of supplemental electric heat; calibrated to close only when outdoor ambient drops below the thermal balance point (e.g., ≤ 32°F).

OT-2: Wired in series with the second bank of electric heat; calibrated to close at approximately 5°F to 10°F below OT-1 (e.g., ≤ 25°F).

Minimum Airflow Requirement: Electric heat packages require a minimum airflow of 45 to 50 CFM per kW (approx. 450 to 500 CFM for a 10 kW strip) to prevent tripping internal automatic reset high-limit thermal switches (140°F–160°F) or blowing one-time thermal fusible links (200°F–220°F).

4. Coefficient of Performance (COP) & Efficiency Standards

Coefficient of Performance (COP): The dimensionless ratio of total useful thermal heat output to the total electrical energy input, both expressed in identical energy units: COP = Heating Output (Watts) Electrical Input (Watts) = Heating Output (BTU/hr) Electrical Input (Watts) × 3.412 \text{COP} = \frac{\text{Heating Output (Watts)}}{\text{Electrical Input (Watts)}} = \frac{\text{Heating Output (BTU/hr)}}{\text{Electrical Input (Watts)} \times 3.412} COP = Electrical Input (Watts) Heating Output (Watts) ​ = Electrical Input (Watts) × 3.412 Heating Output (BTU/hr) ​

Pure electric resistance heat has a fixed COP = 1.0 \text{COP} = 1.0 COP = 1.0 .

Modern air-source heat pumps achieve COP = 3.5 to 4.5 \text{COP} = 3.5\text{ to }4.5 COP = 3.5 to 4.5 at 47°F ambient, and COP = 1.8 to 2.4 \text{COP} = 1.8\text{ to }2.4 COP = 1.8 to 2.4 at 17°F ambient.

HSPF2 (Heating Seasonal Performance Factor 2): Established under federal test procedure AHRI Standard 210/240-2023 (Appendix M1). Represents total seasonal heating output in BTUs divided by total electrical energy consumed in Watt-hours across standardized regional climate bins (Region IV national average and Region V cold climate).

5. Emergency Heat ('E' Terminal) Controls & Diagnostics

Thermostats designed for heat pump applications feature an explicit "Emergency Heat" (EM HT / E) mode: AUXILIARY HEAT vs. EMERGENCY HEAT LOGIC

AUXILIARY HEAT (Normal Operation Below Balance Point):

- Thermostat Terminal: 'W2' or 'AUX'

- Operation: Compressor AND Electric Resistance Heat run SIMULTANEOUSLY.

- Control: Automatic staging via thermostat second stage or outdoor thermostats.

EMERGENCY HEAT (Manual User Switch):

- Thermostat Terminal: 'E'

- Operation: Compressor contactor circuit ('Y') is LOCKED OUT / DE-ENERGIZED.

- Heating Source: 100% Electric Resistance Strip Heat (or Backup Gas Furnace).

- Purpose: Provides emergency heating during mechanical compressor breakdown,

refrigerant leak, or reversing valve failure.

Exam Trap: Emergency Heat should never be selected for routine comfort heating. Because electric resistance heat operates at COP = 1.0 \text{COP} = 1.0 COP = 1.0 , running in Emergency Heat mode triples or quadruples the homeowner's electric utility bill compared to normal heat pump operation.

Loading diagram... Thermal vs Economic Balance Point Comparison