Study guide

16.3 Disinfection of Mains, Storage Facilities & Repaired Components

Arizona Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Arizona Regulatory Framework & ADEQ Certification

1.1 ADEQ Operator Certification Rules & Grade Structure 1.2 Facility Classification & Operator in Direct Responsible Charge (ODRC) 1.3 Arizona Aquifer Protection Permit (APP) Program & BADCT 1.4 AZPDES Surface Water Discharges & Arizona Reclaimed Water Standards 1.5 The WPI Need-to-Know Criteria: What Is Actually on Your Exam

2 Chapter 2: Federal Drinking Water & Clean Water Act Compliance

2.1 Safe Drinking Water Act (SDWA) Primary & Secondary MCLs 2.2 Surface Water Treatment Rules & Revised Total Coliform Rule (RTCR) 2.3 Stage 1 & Stage 2 Disinfectants/Disinfection Byproducts Rules (D/DBPR)

3 Chapter 3: Source Water Assessment, Wells & Watershed Protection

3.1 Groundwater Sources, Well Components & Water Level Measurement 3.2 Surface Water Sources, Intakes & Reservoir Management 3.3 Watershed Management, Contamination Sources & Public Education 3.4 Pretreatment: Aeration, Presedimentation & Algae Control

4 Chapter 4: Source Water Quality, Coagulation & Flocculation

4.1 Arizona Source Water Quality & Arid Climate Challenges 4.2 Coagulation Chemistry, Coagulants & Jar Testing 4.3 Flocculation Basin Design & Process Control 4.4 Sedimentation Basins, Clarifiers & Solids Contact Units

5 Chapter 5: Filtration Systems & Advanced Separation

5.1 Granular Media Filtration Principles & Media Types 5.2 Filter Backwash Operations, Ripening & Filter-to-Waste 5.3 Membrane Filtration & Reverse Osmosis Desalination 5.4 Ion Exchange Softening, Arsenic Removal & GAC Adsorption

6 Chapter 6: Drinking Water Disinfection & Chemical Oxidation

6.1 Chlorine Chemistry & Break-Point Chlorination 6.2 The CT Disinfection Concept & Basin Hydraulics 6.3 Alternative Disinfectants: Chloramines, Ozone, UV & Chlorine Dioxide

7 Chapter 7: Specialized Drinking Water Treatment & Chemical Conditioning

7.1 Iron & Manganese Removal 7.2 Fluoridation: Chemicals, Dosage & Safety 7.3 Corrosion Control, Saturation Indices & the Lead and Copper Rule 7.4 Water Treatment Plant Residuals Handling & Disposal

8 Chapter 8: Water Treatment Plant Equipment Operation & Maintenance

8.1 Raw Water Intake, Screening & Pumping Equipment 8.2 Chemical Feed Equipment, Storage & Metering 8.3 Instrumentation, Online Analyzers, SCADA & Calibration 8.4 Valves, Motors, Auxiliary Systems & Maintenance Programs

9 Chapter 9: Wastewater Preliminary, Primary & Biological Treatment Principles

9.1 Wastewater Characteristics & Preliminary Treatment 9.2 Primary Clarification Design & Settling Mechanics 9.3 Biological Treatment Kinetics & Microbiology

10 Chapter 10: Activated Sludge Processes & Nutrient Removal

10.1 Activated Sludge Configurations & Operational Mass Balance 10.2 Process Control Parameters, Settleability & Troubleshooting 10.3 Biological Nutrient Removal: Nitrification, Denitrification & Phosphorus Removal

11 Chapter 11: Fixed-Film, Lagoon & Advanced Secondary Processes

11.1 Trickling Filters & Attached Growth Fundamentals 11.2 Rotating Biological Contactors & Hybrid Processes 11.3 Stabilization Ponds & Lagoon Systems 11.4 Membrane Bioreactors

12 Chapter 12: Tertiary Treatment, Wastewater Disinfection & Effluent Management

12.1 Tertiary Filtration & Advanced Effluent Polishing 12.2 Wastewater Chlorination & Dechlorination 12.3 Ultraviolet & Ozone Disinfection of Wastewater 12.4 Effluent Disposal, Reclaimed Water Reuse & Permit Compliance

13 Chapter 13: Residuals Management & Sludge Processing

13.1 Sludge Thickening & Digestion Processes 13.2 Sludge Dewatering Technologies & Drying Beds 13.3 EPA Part 503 Biosolids Rules & Arizona Beneficial Use

14 Chapter 14: Wastewater Plant Equipment Operation & Maintenance

14.1 Preliminary & Primary Treatment Equipment 14.2 Aeration Systems, Blowers, Diffusers & Dissolved Oxygen Control 14.3 Wastewater Pumps, Mixers & Chemical Dosing Equipment 14.4 Electrical Systems, Online Analyzers & Auxiliary Power

15 Chapter 15: Water Distribution Infrastructure & Hydraulic Management

15.1 Water Main Materials, Fittings & Appurtenances 15.2 Water Storage, Pressure Management & Water Age 15.3 Cross-Connection Control & Backflow Prevention 15.4 Main Maintenance, Unidirectional Flushing & Leak Detection 15.5 Distribution Hydraulics, Head Loss & C-Factor 15.6 System Mapping, GIS, Plans & Distribution SCADA

16 Chapter 16: Water Main Installation, Repair & Disinfection

16.1 Main & Service Line Installation, Tapping & Thrust Restraint 16.2 New Construction Inspection, Pressure Testing & Utility Locating 16.3 Disinfection of Mains, Storage Facilities & Repaired Components 16.4 Booster Stations, Meters & Storage Facility Inspection

17 Chapter 17: Distribution Water Quality Management & Field Testing

17.1 Distribution Chemical Feed, Dosage Adjustment & Booster Chlorination 17.2 Distribution Sampling Programs & Field Analyses 17.3 Chemical Transport, Storage & Handling in Distribution Operations 17.4 Interpreting Water Quality Data, Complaints & Nitrification Control

18 Chapter 18: Wastewater Collection Systems & Lift Stations

18.1 Gravity Sewer Design, Piping Materials & Manholes 18.2 Inflow & Infiltration (I&I) Assessment & Pipeline Rehabilitation 18.3 Wastewater Lift Stations, Pump Types & Force Mains 18.4 Hydrogen Sulfide Corrosion, Odor Control & Line Cleaning 18.5 Excavation, Heavy Equipment & Surface Restoration

19 Chapter 19: Collection System Cleaning, Inspection & Rehabilitation

19.1 Hydraulic Cleaning, Rodding & Blockage Removal 19.2 CCTV Inspection, Condition Assessment & FOG Control 19.3 Trenchless Rehabilitation: CIPP, Pipe Bursting & Lining 19.4 SSO Response, Flow Monitoring & Capacity Assurance

20 Chapter 20: Laboratory Testing, Quality Control & Monitoring

20.1 Drinking Water Analytical Methods & Compliance Testing 20.2 Wastewater Laboratory Analytics & Process Control Tests 20.3 Sampling Protocols, Chain of Custody & Laboratory QA/QC 20.4 Emerging Contaminants, PFAS & Advanced Analytical Methods

21 Chapter 21: Utility Safety Programs & Emergency Preparedness

21.1 Lockout/Tagout, Electrical Safety & Arc Flash 21.2 Personal Protective Equipment, Fall Protection & Bloodborne Pathogens 21.3 Traffic Control & Work Zone Safety 21.4 Emergency Response Planning & Disaster Recovery 21.5 Heat Illness Prevention, Respiratory Protection & Hearing Conservation

22 Chapter 22: Security, Administration & Utility Management

22.1 Facility Security, Vulnerability Assessment & Cybersecurity 22.2 Recordkeeping, Standard Operating Procedures & Regulatory Reporting 22.3 Budgets, Procurement, Cost Analysis & Capital Improvement Planning 22.4 Asset Management, Energy Optimization & Water Loss Control 22.5 Supervision, Training, Customer Service & Public Communication

23 Chapter 23: Applied Operator Mathematics, Pumping Hydraulics & Utility Safety

23.1 Chemical Feed Calculations & Dosage Problem Solving 23.2 Geometric Volumes, Hydraulic Loading & Detention Time Math 23.3 Pumping Mechanics, System Head & Horsepower Calculations 23.4 Plant Safety: Confined Spaces, Chemical Hazards & OSHA Standards 23.5 Unit Conversions & Using the Supplied Formula/Conversion Table 23.6 Percent Removal, Process Efficiency & Solution Blending

16.3 Disinfection of Mains, Storage Facilities & Repaired Components

Key Takeaways Explain This Topic AI

New and repaired mains must be disinfected and cleared bacteriologically before being returned to service, following AWWA C651 for mains and C652 for storage facilities.

The continuous feed method holds 25 mg/L free chlorine for 24 hours, while the tablet method places calcium hypochlorite tablets in the pipe during assembly for a 24-hour contact period.

Slug application moves a short column of 100 mg/L chlorine through the main so every surface receives at least 3 hours of contact.

Highly chlorinated water must be neutralized before disposal, because discharging it to a wash or storm drain kills aquatic life.

Two consecutive satisfactory bacteriological samples taken at least 24 hours apart are required before a new main is placed in service.

Last updated: September 2026

16.3 Disinfection of Mains, Storage Facilities & Repaired Components

Any time the distribution system is opened, contamination can enter. The Need-to-Know Criteria list "clean and disinfect the finished water storage facilities" and "disinfect components used during install/repairs" as scored operator tasks. The governing standards are AWWA C651 for mains and AWWA C652 for storage facilities.

Before Disinfection: Cleanliness and Flushing

Disinfection cannot compensate for a dirty pipe. Organic material and soil exert chlorine demand and physically shield organisms from contact.

Keep pipe interiors clean during construction and plug open ends whenever work stops.

Swab pipe interiors with a hypochlorite solution as they are laid where the specification requires.

Flush the completed main at a velocity sufficient to carry debris out — commonly at least 2.5 to 3.0 ft/s . Flushing flow for 2.5 ft/s ≈ 2.5 × A × 448.8 \text{Flushing flow for 2.5 ft/s} \approx 2.5 \times A \times 448.8 Flushing flow for 2.5 ft/s ≈ 2.5 × A × 448.8

For an 8-inch main, area is 0.785 × 0.667² = 0.349 ft², so 2.5 × 0.349 × 448.8 ≈ 392 gpm .

The Three AWWA C651 Methods

Method Chlorine concentration Contact time Application

Continuous feed 25 mg/L free chlorine throughout the main 24 hours , retaining at least 10 mg/L at the end The standard method for most new mains

Tablet Calcium hypochlorite tablets affixed inside the pipe during assembly 24 hours Short runs; pipe must be kept dry during construction

Slug 100 mg/L free chlorine in a moving column At least 3 hours of contact with every surface Long transmission mains where filling the whole line at 25 mg/L is impractical

Continuous Feed

Fill the main slowly from a potable source while injecting chlorine so the entire length reaches 25 mg/L free chlorine . Operate every valve and hydrant on the section so chlorinated water contacts all appurtenances. Hold 24 hours , then verify at least 10 mg/L free chlorine remains at the far end. A residual below 10 mg/L means demand exceeded expectation — indicating contamination or debris — and the procedure must be repeated.

Tablet Method

Calcium hypochlorite tablets are attached to the inside top of each pipe section with an approved adhesive as the pipe is laid. When the main is filled, the tablets dissolve and produce the disinfecting concentration. The critical constraint: the pipe must be kept dry during construction , because premature wetting dissolves the tablets before the main is complete. This method also cannot be used where the main cannot be kept clean.

Slug Method

A continuously moving slug of water dosed to 100 mg/L free chlorine is passed slowly through the main so that every interior surface receives at least 3 hours of contact. Chlorine is re-dosed as needed to keep the slug above 100 mg/L as it travels. Used on long transmission mains where holding the entire volume at 25 mg/L would require an impractical quantity of chemical.

Final Flushing and Bacteriological Clearance

After the contact period, flush the highly chlorinated water out until the residual matches that of the distribution system entering the main.

Bacteriological clearance then requires two consecutive sets of satisfactory samples taken at least 24 hours apart , collected from the new main after final flushing. Samples are analyzed for total coliform and, if total coliform is present, for E. coli . Any positive result requires re-disinfection and re-sampling.

Important

The main does not go into service on the strength of the chlorine residual alone. Passing bacteriological results are the release condition, and they cannot be rushed — the 24-hour spacing between sample sets is a minimum, not a target. Sampling must use approved procedures with a sterile bottle containing sodium thiosulfate to neutralize residual chlorine so the sample reflects conditions at collection rather than continued disinfection in the bottle.

Disposal of Highly Chlorinated Water

Warning

Water at 25 to 100 mg/L free chlorine is acutely toxic to aquatic life and must never be discharged to a wash, storm drain, canal, or any water body without neutralization. Arizona's ephemeral washes still support aquatic and riparian ecosystems, and a discharge can also violate AZPDES stormwater requirements.

Neutralization options include sodium bisulfite, sodium metabisulfite, sodium thiosulfate, sodium sulfite, and ascorbic acid , applied to reduce the residual to a level acceptable for discharge. Alternatives are discharge to the sanitary sewer with the treatment plant's permission, containment and hauling, or land application at a rate that will not run off. Dechlorination diffusers on flushing outlets are now common practice.

Erosion control is a companion requirement: the discharge must be directed so that it does not scour the receiving channel, which typically means a diffuser, splash pad, or energy dissipation device.

Storage Facility Disinfection (AWWA C652)

Storage tanks are disinfected after construction, after painting or major repair, and after any entry or cleaning.

  • Method Description
  • Method 1 Fill the entire tank with water dosed to 10 mg/L free chlorine and hold 6 hours

Method 2 Spray or brush all interior surfaces with a 200 mg/L solution, hold 30 minutes , then fill with potable water

Method 3 Fill about 5 percent of tank volume with 50 mg/L chlorinated water, hold 6 hours , then fill the remainder with potable water and hold 24 hours

Method 2 is common because it uses far less chemical and produces less waste to dispose of, and Method 3 is a middle path where full-volume dosing is impractical.

Tank cleaning before disinfection removes accumulated sediment, and confined space entry procedures apply to any tank entry — a point covered in the safety chapter but worth flagging here, since tank interiors are permit-required confined spaces.

Emergency Repairs

A main break under pressure is a different situation. AWWA C651 recognizes abbreviated procedures because the system cannot wait 48 hours for clearance.

Practical measures during an emergency repair:

Keep the trench dewatered and keep the pipe ends out of standing water; contaminated water entering an open main is the principal risk.

Swab or spray the interior of the repair components and the pipe ends with a hypochlorite solution — typically 1 to 5 percent — before assembly.

Maintain positive pressure in the main where at all possible; if pressure is lost, treat it as a higher-risk event.

Flush thoroughly after the repair until clear water and normal chlorine residual return.

Collect bacteriological samples after the repair, even though the main returns to service before results are available.

If the main was depressurized and contaminated , the utility must evaluate whether a precautionary boil-water advisory is warranted, in consultation with the primacy agency.

Loading diagram... Main disinfection methods and clearance sequence