Study guide

11.4 Membrane Bioreactors

Arizona Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Arizona Regulatory Framework & ADEQ Certification

1.1 ADEQ Operator Certification Rules & Grade Structure 1.2 Facility Classification & Operator in Direct Responsible Charge (ODRC) 1.3 Arizona Aquifer Protection Permit (APP) Program & BADCT 1.4 AZPDES Surface Water Discharges & Arizona Reclaimed Water Standards 1.5 The WPI Need-to-Know Criteria: What Is Actually on Your Exam

2 Chapter 2: Federal Drinking Water & Clean Water Act Compliance

2.1 Safe Drinking Water Act (SDWA) Primary & Secondary MCLs 2.2 Surface Water Treatment Rules & Revised Total Coliform Rule (RTCR) 2.3 Stage 1 & Stage 2 Disinfectants/Disinfection Byproducts Rules (D/DBPR)

3 Chapter 3: Source Water Assessment, Wells & Watershed Protection

3.1 Groundwater Sources, Well Components & Water Level Measurement 3.2 Surface Water Sources, Intakes & Reservoir Management 3.3 Watershed Management, Contamination Sources & Public Education 3.4 Pretreatment: Aeration, Presedimentation & Algae Control

4 Chapter 4: Source Water Quality, Coagulation & Flocculation

4.1 Arizona Source Water Quality & Arid Climate Challenges 4.2 Coagulation Chemistry, Coagulants & Jar Testing 4.3 Flocculation Basin Design & Process Control 4.4 Sedimentation Basins, Clarifiers & Solids Contact Units

5 Chapter 5: Filtration Systems & Advanced Separation

5.1 Granular Media Filtration Principles & Media Types 5.2 Filter Backwash Operations, Ripening & Filter-to-Waste 5.3 Membrane Filtration & Reverse Osmosis Desalination 5.4 Ion Exchange Softening, Arsenic Removal & GAC Adsorption

6 Chapter 6: Drinking Water Disinfection & Chemical Oxidation

6.1 Chlorine Chemistry & Break-Point Chlorination 6.2 The CT Disinfection Concept & Basin Hydraulics 6.3 Alternative Disinfectants: Chloramines, Ozone, UV & Chlorine Dioxide

7 Chapter 7: Specialized Drinking Water Treatment & Chemical Conditioning

7.1 Iron & Manganese Removal 7.2 Fluoridation: Chemicals, Dosage & Safety 7.3 Corrosion Control, Saturation Indices & the Lead and Copper Rule 7.4 Water Treatment Plant Residuals Handling & Disposal

8 Chapter 8: Water Treatment Plant Equipment Operation & Maintenance

8.1 Raw Water Intake, Screening & Pumping Equipment 8.2 Chemical Feed Equipment, Storage & Metering 8.3 Instrumentation, Online Analyzers, SCADA & Calibration 8.4 Valves, Motors, Auxiliary Systems & Maintenance Programs

9 Chapter 9: Wastewater Preliminary, Primary & Biological Treatment Principles

9.1 Wastewater Characteristics & Preliminary Treatment 9.2 Primary Clarification Design & Settling Mechanics 9.3 Biological Treatment Kinetics & Microbiology

10 Chapter 10: Activated Sludge Processes & Nutrient Removal

10.1 Activated Sludge Configurations & Operational Mass Balance 10.2 Process Control Parameters, Settleability & Troubleshooting 10.3 Biological Nutrient Removal: Nitrification, Denitrification & Phosphorus Removal

11 Chapter 11: Fixed-Film, Lagoon & Advanced Secondary Processes

11.1 Trickling Filters & Attached Growth Fundamentals 11.2 Rotating Biological Contactors & Hybrid Processes 11.3 Stabilization Ponds & Lagoon Systems 11.4 Membrane Bioreactors

12 Chapter 12: Tertiary Treatment, Wastewater Disinfection & Effluent Management

12.1 Tertiary Filtration & Advanced Effluent Polishing 12.2 Wastewater Chlorination & Dechlorination 12.3 Ultraviolet & Ozone Disinfection of Wastewater 12.4 Effluent Disposal, Reclaimed Water Reuse & Permit Compliance

13 Chapter 13: Residuals Management & Sludge Processing

13.1 Sludge Thickening & Digestion Processes 13.2 Sludge Dewatering Technologies & Drying Beds 13.3 EPA Part 503 Biosolids Rules & Arizona Beneficial Use

14 Chapter 14: Wastewater Plant Equipment Operation & Maintenance

14.1 Preliminary & Primary Treatment Equipment 14.2 Aeration Systems, Blowers, Diffusers & Dissolved Oxygen Control 14.3 Wastewater Pumps, Mixers & Chemical Dosing Equipment 14.4 Electrical Systems, Online Analyzers & Auxiliary Power

15 Chapter 15: Water Distribution Infrastructure & Hydraulic Management

15.1 Water Main Materials, Fittings & Appurtenances 15.2 Water Storage, Pressure Management & Water Age 15.3 Cross-Connection Control & Backflow Prevention 15.4 Main Maintenance, Unidirectional Flushing & Leak Detection 15.5 Distribution Hydraulics, Head Loss & C-Factor 15.6 System Mapping, GIS, Plans & Distribution SCADA

16 Chapter 16: Water Main Installation, Repair & Disinfection

16.1 Main & Service Line Installation, Tapping & Thrust Restraint 16.2 New Construction Inspection, Pressure Testing & Utility Locating 16.3 Disinfection of Mains, Storage Facilities & Repaired Components 16.4 Booster Stations, Meters & Storage Facility Inspection

17 Chapter 17: Distribution Water Quality Management & Field Testing

17.1 Distribution Chemical Feed, Dosage Adjustment & Booster Chlorination 17.2 Distribution Sampling Programs & Field Analyses 17.3 Chemical Transport, Storage & Handling in Distribution Operations 17.4 Interpreting Water Quality Data, Complaints & Nitrification Control

18 Chapter 18: Wastewater Collection Systems & Lift Stations

18.1 Gravity Sewer Design, Piping Materials & Manholes 18.2 Inflow & Infiltration (I&I) Assessment & Pipeline Rehabilitation 18.3 Wastewater Lift Stations, Pump Types & Force Mains 18.4 Hydrogen Sulfide Corrosion, Odor Control & Line Cleaning 18.5 Excavation, Heavy Equipment & Surface Restoration

19 Chapter 19: Collection System Cleaning, Inspection & Rehabilitation

19.1 Hydraulic Cleaning, Rodding & Blockage Removal 19.2 CCTV Inspection, Condition Assessment & FOG Control 19.3 Trenchless Rehabilitation: CIPP, Pipe Bursting & Lining 19.4 SSO Response, Flow Monitoring & Capacity Assurance

20 Chapter 20: Laboratory Testing, Quality Control & Monitoring

20.1 Drinking Water Analytical Methods & Compliance Testing 20.2 Wastewater Laboratory Analytics & Process Control Tests 20.3 Sampling Protocols, Chain of Custody & Laboratory QA/QC 20.4 Emerging Contaminants, PFAS & Advanced Analytical Methods

21 Chapter 21: Utility Safety Programs & Emergency Preparedness

21.1 Lockout/Tagout, Electrical Safety & Arc Flash 21.2 Personal Protective Equipment, Fall Protection & Bloodborne Pathogens 21.3 Traffic Control & Work Zone Safety 21.4 Emergency Response Planning & Disaster Recovery 21.5 Heat Illness Prevention, Respiratory Protection & Hearing Conservation

22 Chapter 22: Security, Administration & Utility Management

22.1 Facility Security, Vulnerability Assessment & Cybersecurity 22.2 Recordkeeping, Standard Operating Procedures & Regulatory Reporting 22.3 Budgets, Procurement, Cost Analysis & Capital Improvement Planning 22.4 Asset Management, Energy Optimization & Water Loss Control 22.5 Supervision, Training, Customer Service & Public Communication

23 Chapter 23: Applied Operator Mathematics, Pumping Hydraulics & Utility Safety

23.1 Chemical Feed Calculations & Dosage Problem Solving 23.2 Geometric Volumes, Hydraulic Loading & Detention Time Math 23.3 Pumping Mechanics, System Head & Horsepower Calculations 23.4 Plant Safety: Confined Spaces, Chemical Hazards & OSHA Standards 23.5 Unit Conversions & Using the Supplied Formula/Conversion Table 23.6 Percent Removal, Process Efficiency & Solution Blending

11.4 Membrane Bioreactors

Key Takeaways Explain This Topic AI

An MBR replaces the secondary clarifier with membrane filtration, so solids separation no longer depends on how well the sludge settles.

Because separation is physical, MBRs run at mixed liquor concentrations of 8,000 to 12,000 mg/L or higher, roughly three to four times conventional activated sludge.

Transmembrane pressure is the primary fouling indicator, and a rising TMP at constant flux means the membranes need cleaning.

Fine screening at 1 to 3 mm ahead of the bioreactor is mandatory, because hair and fibrous material braid onto membrane fibers and cause irreversible damage.

Maintenance cleaning is a frequent short chemical soak, while recovery cleaning is an infrequent intensive clean that restores permeability after fouling has accumulated.

Last updated: September 2026

11.4 Membrane Bioreactors

A membrane bioreactor (MBR) is activated sludge in which the secondary clarifier has been replaced by membrane filtration . That single substitution changes almost everything about how the process is operated.

Why Removing the Clarifier Matters

In conventional activated sludge, everything downstream depends on whether the sludge settles . Bulking, poor settleability, and rising sludge limit how much mixed liquor you can carry, because the clarifier must be able to separate it.

An MBR separates solids by physical exclusion through a membrane , so settleability becomes irrelevant to compliance. The consequences:

  • Consequence Detail
  • High MLSS 8,000 to 12,000 mg/L and above, versus 2,000 to 4,000 mg/L conventional
  • Small footprint Higher biomass per unit volume plus no clarifier
  • Complete solids removal Effluent TSS essentially non-detectable; turbidity below 0.2 NTU

Disinfection benefit Membranes physically remove bacteria and protozoa, providing substantial log removal credit

  • Long SRT decoupled from HRT Sludge age is set by wasting alone, independent of settling
  • Reliable nitrification Long achievable sludge age retains nitrifiers
  • Reuse quality Effluent is well suited to reclaimed water production

Trade-offs are real: higher energy consumption, membrane replacement cost every several years, greater operational complexity , and sensitivity to fouling.

Configurations

Submerged (immersed) : membrane modules sit directly in the bioreactor or in a separate membrane tank. Permeate is drawn through under vacuum. The dominant configuration.

Sidestream (external) : mixed liquor is pumped through membrane modules outside the tank under pressure. Higher energy; used for industrial applications.

Membrane formats are hollow fiber and flat sheet , generally in the microfiltration to ultrafiltration range, with pore sizes around 0.04 to 0.4 micron.

Core Operating Parameters

Flux Flux = Permeate Flow Membrane Area \text{Flux} = \frac{\text{Permeate Flow}}{\text{Membrane Area}} Flux = Membrane Area Permeate Flow ​

Expressed in gallons per square foot per day (gfd) or liters per square meter per hour (LMH). Operating above the sustainable flux accelerates fouling disproportionately.

Transmembrane Pressure

TMP is the pressure difference driving water across the membrane. It is the primary fouling indicator. Permeability = Flux TMP \text{Permeability} = \frac{\text{Flux}}{\text{TMP}} Permeability = TMP Flux ​

Important

Rising TMP at constant flux means fouling. Equivalently, falling permeability means fouling. Trend TMP daily. A slow rise is normal and is addressed by routine maintenance cleaning; a rapid rise signals a specific problem such as a screening failure, a solids excursion, or a sludge quality change.

Relaxation and Backpulsing

Membranes are operated cyclically, not continuously — for example nine minutes of filtration followed by one minute of relaxation (permeate pump off while air scour continues), or brief backpulsing in which permeate is pushed backward through the membrane. Both dislodge the cake layer and are essential to sustained operation.

Air Scour

Coarse-bubble air is directed along the membrane surface to scour accumulated solids. This is separate from the process aeration that supplies oxygen to the biology, and it is a major share of an MBR's energy consumption.

Fouling and Cleaning

  • Fouling type Cause Removed by
  • Cake layer Solids accumulating on the surface Air scour, relaxation, backpulse
  • Organic/biofouling Extracellular polymeric substances, biofilm Sodium hypochlorite cleaning
  • Inorganic scaling Calcium carbonate, struvite, iron Citric or oxalic acid cleaning
  • Irreversible Pore plugging, physical damage Not recoverable; requires replacement
  • Two Levels of Chemical Cleaning
  • Maintenance cleaning Recovery cleaning
  • Frequency Weekly to monthly Every 6 to 12 months, or when permeability drops below a threshold
  • Duration Short, often under an hour Extended soak, several hours
  • Concentration Low High
  • Location Usually in place In place or in a separate tank
  • Purpose Prevent fouling accumulation Restore lost permeability

Both typically use hypochlorite for organic fouling and an acid for scaling. Never mix them — sequence them with a rinse between, since hypochlorite and acid together liberate chlorine gas.

  • Protecting the Membranes
  • Fine Screening Is Mandatory

1 to 3 mm fine screening ahead of the bioreactor is not optional. Hair, lint, and fibrous material braid around hollow fibers, forming ropes that abrade and eventually sever them. This damage is irreversible , and a screening bypass during a high-flow event can cost a membrane cassette.

Other Protections

Fats, oils, and grease coat membranes and are poorly removed by cleaning; upstream FOG control matters more at an MBR than at a conventional plant.

Foaming is aggravated by high MLSS; control with defoamer, sludge age adjustment, and by addressing filamentous causes.

Membrane integrity testing — typically a pressure decay test — verifies that no fibers are broken, which matters because integrity underpins the pathogen removal credit.

Do not let membranes dry out. A membrane allowed to dry may suffer permanent permeability loss. Follow the manufacturer's preservation procedure for any extended outage.

Aeration at High MLSS

Oxygen transfer efficiency declines as mixed liquor concentration rises, because the thicker mixed liquor is more viscous and resists bubble dispersion. The correction factor applied to oxygen transfer, commonly called alpha, drops significantly at MBR solids concentrations. Operators therefore cannot assume that the blower capacity adequate for a 3,000 mg/L conventional basin will deliver equivalent oxygen at 10,000 mg/L, and dissolved oxygen must be monitored directly rather than inferred from airflow.