Study guide

7.3 Corrosion Control, Saturation Indices & the Lead and Copper Rule

Arizona Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Arizona Regulatory Framework & ADEQ Certification

1.1 ADEQ Operator Certification Rules & Grade Structure 1.2 Facility Classification & Operator in Direct Responsible Charge (ODRC) 1.3 Arizona Aquifer Protection Permit (APP) Program & BADCT 1.4 AZPDES Surface Water Discharges & Arizona Reclaimed Water Standards 1.5 The WPI Need-to-Know Criteria: What Is Actually on Your Exam

2 Chapter 2: Federal Drinking Water & Clean Water Act Compliance

2.1 Safe Drinking Water Act (SDWA) Primary & Secondary MCLs 2.2 Surface Water Treatment Rules & Revised Total Coliform Rule (RTCR) 2.3 Stage 1 & Stage 2 Disinfectants/Disinfection Byproducts Rules (D/DBPR)

3 Chapter 3: Source Water Assessment, Wells & Watershed Protection

3.1 Groundwater Sources, Well Components & Water Level Measurement 3.2 Surface Water Sources, Intakes & Reservoir Management 3.3 Watershed Management, Contamination Sources & Public Education 3.4 Pretreatment: Aeration, Presedimentation & Algae Control

4 Chapter 4: Source Water Quality, Coagulation & Flocculation

4.1 Arizona Source Water Quality & Arid Climate Challenges 4.2 Coagulation Chemistry, Coagulants & Jar Testing 4.3 Flocculation Basin Design & Process Control 4.4 Sedimentation Basins, Clarifiers & Solids Contact Units

5 Chapter 5: Filtration Systems & Advanced Separation

5.1 Granular Media Filtration Principles & Media Types 5.2 Filter Backwash Operations, Ripening & Filter-to-Waste 5.3 Membrane Filtration & Reverse Osmosis Desalination 5.4 Ion Exchange Softening, Arsenic Removal & GAC Adsorption

6 Chapter 6: Drinking Water Disinfection & Chemical Oxidation

6.1 Chlorine Chemistry & Break-Point Chlorination 6.2 The CT Disinfection Concept & Basin Hydraulics 6.3 Alternative Disinfectants: Chloramines, Ozone, UV & Chlorine Dioxide

7 Chapter 7: Specialized Drinking Water Treatment & Chemical Conditioning

7.1 Iron & Manganese Removal 7.2 Fluoridation: Chemicals, Dosage & Safety 7.3 Corrosion Control, Saturation Indices & the Lead and Copper Rule 7.4 Water Treatment Plant Residuals Handling & Disposal

8 Chapter 8: Water Treatment Plant Equipment Operation & Maintenance

8.1 Raw Water Intake, Screening & Pumping Equipment 8.2 Chemical Feed Equipment, Storage & Metering 8.3 Instrumentation, Online Analyzers, SCADA & Calibration 8.4 Valves, Motors, Auxiliary Systems & Maintenance Programs

9 Chapter 9: Wastewater Preliminary, Primary & Biological Treatment Principles

9.1 Wastewater Characteristics & Preliminary Treatment 9.2 Primary Clarification Design & Settling Mechanics 9.3 Biological Treatment Kinetics & Microbiology

10 Chapter 10: Activated Sludge Processes & Nutrient Removal

10.1 Activated Sludge Configurations & Operational Mass Balance 10.2 Process Control Parameters, Settleability & Troubleshooting 10.3 Biological Nutrient Removal: Nitrification, Denitrification & Phosphorus Removal

11 Chapter 11: Fixed-Film, Lagoon & Advanced Secondary Processes

11.1 Trickling Filters & Attached Growth Fundamentals 11.2 Rotating Biological Contactors & Hybrid Processes 11.3 Stabilization Ponds & Lagoon Systems 11.4 Membrane Bioreactors

12 Chapter 12: Tertiary Treatment, Wastewater Disinfection & Effluent Management

12.1 Tertiary Filtration & Advanced Effluent Polishing 12.2 Wastewater Chlorination & Dechlorination 12.3 Ultraviolet & Ozone Disinfection of Wastewater 12.4 Effluent Disposal, Reclaimed Water Reuse & Permit Compliance

13 Chapter 13: Residuals Management & Sludge Processing

13.1 Sludge Thickening & Digestion Processes 13.2 Sludge Dewatering Technologies & Drying Beds 13.3 EPA Part 503 Biosolids Rules & Arizona Beneficial Use

14 Chapter 14: Wastewater Plant Equipment Operation & Maintenance

14.1 Preliminary & Primary Treatment Equipment 14.2 Aeration Systems, Blowers, Diffusers & Dissolved Oxygen Control 14.3 Wastewater Pumps, Mixers & Chemical Dosing Equipment 14.4 Electrical Systems, Online Analyzers & Auxiliary Power

15 Chapter 15: Water Distribution Infrastructure & Hydraulic Management

15.1 Water Main Materials, Fittings & Appurtenances 15.2 Water Storage, Pressure Management & Water Age 15.3 Cross-Connection Control & Backflow Prevention 15.4 Main Maintenance, Unidirectional Flushing & Leak Detection 15.5 Distribution Hydraulics, Head Loss & C-Factor 15.6 System Mapping, GIS, Plans & Distribution SCADA

16 Chapter 16: Water Main Installation, Repair & Disinfection

16.1 Main & Service Line Installation, Tapping & Thrust Restraint 16.2 New Construction Inspection, Pressure Testing & Utility Locating 16.3 Disinfection of Mains, Storage Facilities & Repaired Components 16.4 Booster Stations, Meters & Storage Facility Inspection

17 Chapter 17: Distribution Water Quality Management & Field Testing

17.1 Distribution Chemical Feed, Dosage Adjustment & Booster Chlorination 17.2 Distribution Sampling Programs & Field Analyses 17.3 Chemical Transport, Storage & Handling in Distribution Operations 17.4 Interpreting Water Quality Data, Complaints & Nitrification Control

18 Chapter 18: Wastewater Collection Systems & Lift Stations

18.1 Gravity Sewer Design, Piping Materials & Manholes 18.2 Inflow & Infiltration (I&I) Assessment & Pipeline Rehabilitation 18.3 Wastewater Lift Stations, Pump Types & Force Mains 18.4 Hydrogen Sulfide Corrosion, Odor Control & Line Cleaning 18.5 Excavation, Heavy Equipment & Surface Restoration

19 Chapter 19: Collection System Cleaning, Inspection & Rehabilitation

19.1 Hydraulic Cleaning, Rodding & Blockage Removal 19.2 CCTV Inspection, Condition Assessment & FOG Control 19.3 Trenchless Rehabilitation: CIPP, Pipe Bursting & Lining 19.4 SSO Response, Flow Monitoring & Capacity Assurance

20 Chapter 20: Laboratory Testing, Quality Control & Monitoring

20.1 Drinking Water Analytical Methods & Compliance Testing 20.2 Wastewater Laboratory Analytics & Process Control Tests 20.3 Sampling Protocols, Chain of Custody & Laboratory QA/QC 20.4 Emerging Contaminants, PFAS & Advanced Analytical Methods

21 Chapter 21: Utility Safety Programs & Emergency Preparedness

21.1 Lockout/Tagout, Electrical Safety & Arc Flash 21.2 Personal Protective Equipment, Fall Protection & Bloodborne Pathogens 21.3 Traffic Control & Work Zone Safety 21.4 Emergency Response Planning & Disaster Recovery 21.5 Heat Illness Prevention, Respiratory Protection & Hearing Conservation

22 Chapter 22: Security, Administration & Utility Management

22.1 Facility Security, Vulnerability Assessment & Cybersecurity 22.2 Recordkeeping, Standard Operating Procedures & Regulatory Reporting 22.3 Budgets, Procurement, Cost Analysis & Capital Improvement Planning 22.4 Asset Management, Energy Optimization & Water Loss Control 22.5 Supervision, Training, Customer Service & Public Communication

23 Chapter 23: Applied Operator Mathematics, Pumping Hydraulics & Utility Safety

23.1 Chemical Feed Calculations & Dosage Problem Solving 23.2 Geometric Volumes, Hydraulic Loading & Detention Time Math 23.3 Pumping Mechanics, System Head & Horsepower Calculations 23.4 Plant Safety: Confined Spaces, Chemical Hazards & OSHA Standards 23.5 Unit Conversions & Using the Supplied Formula/Conversion Table 23.6 Percent Removal, Process Efficiency & Solution Blending

7.3 Corrosion Control, Saturation Indices & the Lead and Copper Rule

Key Takeaways Explain This Topic AI

A positive Langelier Saturation Index means water tends to deposit calcium carbonate scale, a negative index means it tends to dissolve it and is corrosive, and zero means the water is at equilibrium.

The Lead and Copper Rule action levels are 0.015 mg/L for lead and 1.3 mg/L for copper at the 90th percentile of first-draw tap samples, and an action level is not a maximum contaminant level.

Lead and copper compliance samples are first-draw, one-liter samples collected after at least six hours of stagnation from taps at high-risk sites.

Orthophosphate is the most widely used corrosion inhibitor because it forms a low-solubility lead and copper phosphate film on pipe walls.

The Lead and Copper Rule Revisions add a 0.010 mg/L trigger level, mandatory service line inventories, and school and childcare sampling, all of which raise the operational stakes on stable water chemistry.

Last updated: September 2026

7.3 Corrosion Control, Saturation Indices & the Lead and Copper Rule

Corrosion is the deterioration of a material by reaction with its environment. In a water system it is simultaneously an asset problem (pipe failures, red water, loss of capacity) and a public health problem (lead and copper leaching into drinking water at the tap). The Need-to-Know Criteria list "corrosion control chemicals (e.g., phosphates)" among the chemicals to ensure proper use of, and "corrosion control (e.g., Langelier Saturation Index, phosphate)" among laboratory analyses.

What Drives Corrosion

  • Factor Effect
  • Low pH Strongly increases corrosivity; the single most influential factor
  • Low alkalinity Poor buffering, so pH swings easily; less carbonate available to form protective scale
  • High dissolved oxygen Supports the cathodic reaction
  • High temperature Roughly doubles reaction rate per 10°C rise; hot water lines corrode faster
  • High total dissolved solids and chloride Increases conductivity, accelerating electrochemical corrosion
  • High velocity Erosion corrosion, especially at elbows and in copper
  • Dissimilar metals in contact Galvanic corrosion — the less noble metal sacrifices
  • Microbial activity Microbiologically influenced corrosion; sulfate-reducing bacteria under tubercles

Galvanic corrosion deserves particular attention because it is common at partial repairs. When copper is joined directly to galvanized steel or to a lead service line, the more active metal corrodes preferentially. A dielectric union breaks the electrical path and is the standard remedy.

  • Common Corrosion Indicators at the Tap
  • Blue-green staining on fixtures → copper corrosion
  • Red-brown water and staining → iron corrosion, often from unlined cast iron
  • Black water → often manganese, but can be sulfide corrosion
  • Metallic taste → copper or iron
  • Pinhole leaks in copper tubing → pitting corrosion, sometimes velocity-driven
  • Saturation Indices

The classic tool is the Langelier Saturation Index (LSI) , which compares actual pH to the pH at which the water would be exactly saturated with calcium carbonate. LSI = pH − pH s \text{LSI} = \text{pH} - \text{pH}_s LSI = pH − pH s ​

where pH_s is the saturation pH computed from calcium hardness, total alkalinity, total dissolved solids, and temperature.

  • LSI Interpretation
  • Positive (> 0) Supersaturated; water tends to deposit calcium carbonate scale
  • Zero At equilibrium; balanced
  • Negative (< 0) Undersaturated; water tends to dissolve calcium carbonate and is corrosive

Worked example. Finished water has pH 7.4 and a calculated pH_s of 8.1. LSI = 7.4 − 8.1 = − 0.7 \text{LSI} = 7.4 - 8.1 = -0.7 LSI = 7.4 − 8.1 = − 0.7

The water is undersaturated and corrosive. Raising pH toward 8.1 with caustic soda, lime, or soda ash moves it toward balance.

Important

LSI predicts a tendency , not a rate, and it says nothing directly about lead. A slightly positive LSI is the usual target, but a strongly positive index causes scaling that reduces pipe capacity and fouls water heaters. Related indices you may see include the Ryznar Stability Index and the Aggressiveness Index , which is used for asbestos-cement pipe.

The Lead and Copper Rule

Lead in drinking water almost never comes from the source. It comes from lead service lines, lead solder (banned in 1986 but present in older plumbing), and brass fixtures . Copper comes from copper tubing. Because the metal enters the water in the customer's plumbing, the rule is written around tap sampling , not plant sampling.

Action Levels

  • Metal Action level Basis
  • Lead 0.015 mg/L (15 ppb) 90th percentile of first-draw tap samples
  • Copper 1.3 mg/L 90th percentile of first-draw tap samples

Warning

An action level is not a maximum contaminant level. Exceeding it is not automatically a violation; it triggers required actions — corrosion control treatment steps, public education, water quality parameter monitoring, and in some circumstances service line replacement. The maximum contaminant level goal for lead is zero, because no level of lead exposure is considered safe.

Sampling Protocol

Compliance samples must be:

  • First-draw , collected after the water has stood motionless in the plumbing for at least 6 hours
  • One liter in volume
  • Taken from a cold water tap normally used for drinking, typically the kitchen or bathroom

Collected from high-risk (Tier 1) sites : homes with lead service lines, copper piping with lead solder installed before the 1986 ban, or known lead pipe

Do not remove or clean the aerator before sampling , and do not flush the line first — both defeat the purpose of capturing the water that actually sat against the plumbing. The 90th percentile is computed from the set of results, so one high house does not by itself create an exceedance, and a well-designed site pool matters.

  • Corrosion Control Treatment
  • pH and Alkalinity Adjustment

Raising pH and alkalinity reduces lead and copper solubility and supports formation of a protective carbonate scale. Chemicals used:

  • Sodium hydroxide (caustic soda) — raises pH, adds no hardness
  • Lime (calcium hydroxide) — raises pH and adds calcium
  • Soda ash (sodium carbonate) — raises pH and alkalinity
  • Carbon dioxide — used to lower pH when overshoot occurs
  • Corrosion Inhibitors

Orthophosphate is the workhorse. It forms a low-solubility lead phosphate and copper phosphate film on the pipe wall. Typical doses run about 1 to 3 mg/L as PO₄, and maintaining pH in the effective range matters as much as the dose itself.

Blended ortho-polyphosphate provides both film formation and some sequestration of iron and manganese.

Silicates are used less commonly.

Note

The passivating film takes weeks to months to establish and it is fragile. Changing source water or disinfectant type without evaluating the corrosion chemistry can destabilize an existing film and release accumulated lead. This is the mechanism behind the most serious lead-in-water incidents in the United States, and it is why any source change, or a switch between free chlorine and chloramine, demands a corrosion control review first.

The Lead and Copper Rule Revisions

The LCRR added requirements operators must know:

A trigger level of 0.010 mg/L for lead, below the 0.015 mg/L action level, which initiates planning and optimization before an exceedance occurs

  • A mandatory service line material inventory , made publicly accessible
  • Find-and-fix requirements when an individual sample exceeds the action level
  • Sampling in schools and childcare facilities
  • Revised service line replacement obligations, with an emphasis on full rather than partial replacement

Partial lead service line replacement can temporarily increase lead release by disturbing the pipe and creating a galvanic couple between the new copper and the remaining lead, which is why full replacement is strongly preferred.

Loading diagram... Corrosion control logic and Lead and Copper Rule response