Study guide
8.1 Raw Water Intake, Screening & Pumping Equipment
Arizona Water/Wastewater Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Arizona Regulatory Framework & ADEQ Certification
1.1 ADEQ Operator Certification Rules & Grade Structure 1.2 Facility Classification & Operator in Direct Responsible Charge (ODRC) 1.3 Arizona Aquifer Protection Permit (APP) Program & BADCT 1.4 AZPDES Surface Water Discharges & Arizona Reclaimed Water Standards 1.5 The WPI Need-to-Know Criteria: What Is Actually on Your Exam
2 Chapter 2: Federal Drinking Water & Clean Water Act Compliance
2.1 Safe Drinking Water Act (SDWA) Primary & Secondary MCLs 2.2 Surface Water Treatment Rules & Revised Total Coliform Rule (RTCR) 2.3 Stage 1 & Stage 2 Disinfectants/Disinfection Byproducts Rules (D/DBPR)
3 Chapter 3: Source Water Assessment, Wells & Watershed Protection
3.1 Groundwater Sources, Well Components & Water Level Measurement 3.2 Surface Water Sources, Intakes & Reservoir Management 3.3 Watershed Management, Contamination Sources & Public Education 3.4 Pretreatment: Aeration, Presedimentation & Algae Control
4 Chapter 4: Source Water Quality, Coagulation & Flocculation
4.1 Arizona Source Water Quality & Arid Climate Challenges 4.2 Coagulation Chemistry, Coagulants & Jar Testing 4.3 Flocculation Basin Design & Process Control 4.4 Sedimentation Basins, Clarifiers & Solids Contact Units
5 Chapter 5: Filtration Systems & Advanced Separation
5.1 Granular Media Filtration Principles & Media Types 5.2 Filter Backwash Operations, Ripening & Filter-to-Waste 5.3 Membrane Filtration & Reverse Osmosis Desalination 5.4 Ion Exchange Softening, Arsenic Removal & GAC Adsorption
6 Chapter 6: Drinking Water Disinfection & Chemical Oxidation
6.1 Chlorine Chemistry & Break-Point Chlorination 6.2 The CT Disinfection Concept & Basin Hydraulics 6.3 Alternative Disinfectants: Chloramines, Ozone, UV & Chlorine Dioxide
7 Chapter 7: Specialized Drinking Water Treatment & Chemical Conditioning
7.1 Iron & Manganese Removal 7.2 Fluoridation: Chemicals, Dosage & Safety 7.3 Corrosion Control, Saturation Indices & the Lead and Copper Rule 7.4 Water Treatment Plant Residuals Handling & Disposal
8 Chapter 8: Water Treatment Plant Equipment Operation & Maintenance
8.1 Raw Water Intake, Screening & Pumping Equipment 8.2 Chemical Feed Equipment, Storage & Metering 8.3 Instrumentation, Online Analyzers, SCADA & Calibration 8.4 Valves, Motors, Auxiliary Systems & Maintenance Programs
9 Chapter 9: Wastewater Preliminary, Primary & Biological Treatment Principles
9.1 Wastewater Characteristics & Preliminary Treatment 9.2 Primary Clarification Design & Settling Mechanics 9.3 Biological Treatment Kinetics & Microbiology
10 Chapter 10: Activated Sludge Processes & Nutrient Removal
10.1 Activated Sludge Configurations & Operational Mass Balance 10.2 Process Control Parameters, Settleability & Troubleshooting 10.3 Biological Nutrient Removal: Nitrification, Denitrification & Phosphorus Removal
11 Chapter 11: Fixed-Film, Lagoon & Advanced Secondary Processes
11.1 Trickling Filters & Attached Growth Fundamentals 11.2 Rotating Biological Contactors & Hybrid Processes 11.3 Stabilization Ponds & Lagoon Systems 11.4 Membrane Bioreactors
12 Chapter 12: Tertiary Treatment, Wastewater Disinfection & Effluent Management
12.1 Tertiary Filtration & Advanced Effluent Polishing 12.2 Wastewater Chlorination & Dechlorination 12.3 Ultraviolet & Ozone Disinfection of Wastewater 12.4 Effluent Disposal, Reclaimed Water Reuse & Permit Compliance
13 Chapter 13: Residuals Management & Sludge Processing
13.1 Sludge Thickening & Digestion Processes 13.2 Sludge Dewatering Technologies & Drying Beds 13.3 EPA Part 503 Biosolids Rules & Arizona Beneficial Use
14 Chapter 14: Wastewater Plant Equipment Operation & Maintenance
14.1 Preliminary & Primary Treatment Equipment 14.2 Aeration Systems, Blowers, Diffusers & Dissolved Oxygen Control 14.3 Wastewater Pumps, Mixers & Chemical Dosing Equipment 14.4 Electrical Systems, Online Analyzers & Auxiliary Power
15 Chapter 15: Water Distribution Infrastructure & Hydraulic Management
15.1 Water Main Materials, Fittings & Appurtenances 15.2 Water Storage, Pressure Management & Water Age 15.3 Cross-Connection Control & Backflow Prevention 15.4 Main Maintenance, Unidirectional Flushing & Leak Detection 15.5 Distribution Hydraulics, Head Loss & C-Factor 15.6 System Mapping, GIS, Plans & Distribution SCADA
16 Chapter 16: Water Main Installation, Repair & Disinfection
16.1 Main & Service Line Installation, Tapping & Thrust Restraint 16.2 New Construction Inspection, Pressure Testing & Utility Locating 16.3 Disinfection of Mains, Storage Facilities & Repaired Components 16.4 Booster Stations, Meters & Storage Facility Inspection
17 Chapter 17: Distribution Water Quality Management & Field Testing
17.1 Distribution Chemical Feed, Dosage Adjustment & Booster Chlorination 17.2 Distribution Sampling Programs & Field Analyses 17.3 Chemical Transport, Storage & Handling in Distribution Operations 17.4 Interpreting Water Quality Data, Complaints & Nitrification Control
18 Chapter 18: Wastewater Collection Systems & Lift Stations
18.1 Gravity Sewer Design, Piping Materials & Manholes 18.2 Inflow & Infiltration (I&I) Assessment & Pipeline Rehabilitation 18.3 Wastewater Lift Stations, Pump Types & Force Mains 18.4 Hydrogen Sulfide Corrosion, Odor Control & Line Cleaning 18.5 Excavation, Heavy Equipment & Surface Restoration
19 Chapter 19: Collection System Cleaning, Inspection & Rehabilitation
19.1 Hydraulic Cleaning, Rodding & Blockage Removal 19.2 CCTV Inspection, Condition Assessment & FOG Control 19.3 Trenchless Rehabilitation: CIPP, Pipe Bursting & Lining 19.4 SSO Response, Flow Monitoring & Capacity Assurance
20 Chapter 20: Laboratory Testing, Quality Control & Monitoring
20.1 Drinking Water Analytical Methods & Compliance Testing 20.2 Wastewater Laboratory Analytics & Process Control Tests 20.3 Sampling Protocols, Chain of Custody & Laboratory QA/QC 20.4 Emerging Contaminants, PFAS & Advanced Analytical Methods
21 Chapter 21: Utility Safety Programs & Emergency Preparedness
21.1 Lockout/Tagout, Electrical Safety & Arc Flash 21.2 Personal Protective Equipment, Fall Protection & Bloodborne Pathogens 21.3 Traffic Control & Work Zone Safety 21.4 Emergency Response Planning & Disaster Recovery 21.5 Heat Illness Prevention, Respiratory Protection & Hearing Conservation
22 Chapter 22: Security, Administration & Utility Management
22.1 Facility Security, Vulnerability Assessment & Cybersecurity 22.2 Recordkeeping, Standard Operating Procedures & Regulatory Reporting 22.3 Budgets, Procurement, Cost Analysis & Capital Improvement Planning 22.4 Asset Management, Energy Optimization & Water Loss Control 22.5 Supervision, Training, Customer Service & Public Communication
23 Chapter 23: Applied Operator Mathematics, Pumping Hydraulics & Utility Safety
23.1 Chemical Feed Calculations & Dosage Problem Solving 23.2 Geometric Volumes, Hydraulic Loading & Detention Time Math 23.3 Pumping Mechanics, System Head & Horsepower Calculations 23.4 Plant Safety: Confined Spaces, Chemical Hazards & OSHA Standards 23.5 Unit Conversions & Using the Supplied Formula/Conversion Table 23.6 Percent Removal, Process Efficiency & Solution Blending
8.1 Raw Water Intake, Screening & Pumping Equipment
Key Takeaways Explain This Topic AI
Net positive suction head available must always exceed net positive suction head required, or the pump will cavitate and destroy its impeller.
Cavitation sounds like gravel passing through the pump and is corrected by raising suction pressure, lowering suction lift, or reducing the flow rate, never by throttling the suction valve.
Throttle a centrifugal pump on the discharge side only; throttling the suction starves the impeller and induces cavitation.
Rising differential head loss across an intake screen means the screen is blinding and needs cleaning before the low-lift pumps lose suction.
Vertical turbine pumps are the standard for wells and wet pits because the bowl assembly stays submerged and self-primed.
Last updated: September 2026
8.1 Raw Water Intake, Screening & Pumping Equipment
The Need-to-Know Criteria require Water Treatment operators to inspect, maintain, and operate "raw water intake, screening, and pumping," to "operate and maintain pumps, drivers, and auxiliary equipment," and to "perform efficiency tests on pumps and related equipment (e.g., pump curves)." Pumping questions appear on all four discipline exams, so this material pays off no matter which test you sit.
Intake Structures and Screening
- Component Purpose Operator attention
- Trash rack Excludes logs, branches, large debris Rake or clear; watch differential
- Bar screen Excludes intermediate debris Manual or mechanically raked
Traveling water screen Continuous fine screening on a moving belt Spray wash pressure, belt tracking, drive chain
- Intake tower ports and gates Depth selection Gate operator lubrication, position indication, stem alignment
- Low-lift (raw water) pumps Move raw water to the plant Suction conditions, bearing and seal condition
Differential head loss across a screen is the primary diagnostic. As debris, algae, or mussels blind the screen, the water level upstream rises relative to downstream. Left alone, the differential eventually starves the low-lift pumps of suction and causes cavitation or loss of prime — and in extreme cases can structurally damage the screen panel.
Arizona-specific concerns: quagga mussel colonization on screen faces, guides, and in raw water piping from Colorado River water; algal mats during summer; and debris surges during monsoon runoff.
Pump Types in Raw Water Service
- Type Description Typical use
- Horizontal centrifugal (end suction) Impeller in a volute casing, horizontal shaft General plant service
- Split case centrifugal Casing splits for access; often double suction High-flow raw and finished water pumping
Vertical turbine Multiple bowl-and-impeller stages on a vertical shaft, bowls submerged Wells and wet pits — self-primed because the bowls stay under water
- Submersible Motor and pump both submerged Wells, wet wells, sumps
- Axial flow (propeller) Moves large volumes at low head Raw water lifts, flood pumping
- Positive displacement Fixed volume per stroke or revolution Chemical metering and sludge
Vertical turbines dominate well and wet-pit service for one practical reason: the bowl assembly is always submerged, so the pump never needs priming and never loses suction as long as the water level stays above the bowls.
- Pump Theory Operators Must Apply
- Head Terms
Static suction lift : the pump is above the water source; the pump must lift water to itself.
Static suction head : the source is above the pump centerline; water flows in under pressure.
Static discharge head : elevation the water must be raised on the discharge side.
Total static head : total elevation difference from source surface to discharge surface.
Friction head : pressure lost to pipe wall friction, fittings, and valves.
Total dynamic head (TDH) : total static head plus friction head plus velocity head — the actual work the pump does. TDH = Total Static Head + Friction Head + Velocity Head \text{TDH} = \text{Total Static Head} + \text{Friction Head} + \text{Velocity Head} TDH = Total Static Head + Friction Head + Velocity Head 1 psi = 2.31 ft of head 1 ft of head = 0.433 psi 1\text{ psi} = 2.31\text{ ft of head} \qquad 1\text{ ft of head} = 0.433\text{ psi} 1 psi = 2.31 ft of head 1 ft of head = 0.433 psi
Net Positive Suction Head and Cavitation
Net positive suction head available (NPSHA) is the absolute pressure at the pump suction above the vapor pressure of the liquid. Net positive suction head required (NPSHR) is what the pump needs to avoid vaporizing the liquid at the impeller eye, and it comes from the manufacturer's curve. NPSHA must always exceed NPSHR. \textbf{NPSHA must always exceed NPSHR.} NPSHA must always exceed NPSHR.
When it does not, water flashes to vapor at the impeller eye and the bubbles collapse violently as pressure recovers across the impeller. That is cavitation .
- Cavitation sign Detail
- Sound Like gravel or marbles passing through the pump — the classic description
- Vibration Rough, erratic running
- Gauges Fluctuating discharge pressure and flow
- Damage Pitting and erosion of the impeller vanes and casing
Corrective actions: raise the suction water level, lower the pump elevation, shorten and enlarge the suction piping, clean a blinded screen or clogged suction strainer, open a partially closed suction valve, or reduce the flow rate.
Warning
Never throttle a centrifugal pump on the suction side. Throttling suction reduces NPSHA and directly causes the cavitation you are trying to avoid. All throttling is done on the discharge valve. This is one of the most frequently tested operating rules in the entire pump section.
Priming
A centrifugal pump moves water, not air. If the casing contains air, the pump spins without developing head — it is air bound . Suction-lift installations must be primed by a foot valve with fill connection, a vacuum priming system, or a self-priming pump design. Submerged installations such as vertical turbines and submersibles are self-primed.
Pump Curves and Efficiency
The manufacturer's curve plots head against flow. As flow increases, head decreases. The operating point is where the pump curve intersects the system head curve .
Best efficiency point (BEP) is where the pump runs most efficiently and with the least vibration and bearing load. Running far off BEP shortens life.
Shutoff head is head at zero flow; running against a closed discharge valve for more than a moment overheats the pump.
Pumps in series add head. Pumps in parallel add flow.
Affinity Laws
For a change in speed (N): Q 2 = Q 1 ( N 2 N 1 ) H 2 = H 1 ( N 2 N 1 ) 2 P 2 = P 1 ( N 2 N 1 ) 3 Q_2 = Q_1\left(\frac{N_2}{N_1}\right) \qquad H_2 = H_1\left(\frac{N_2}{N_1}\right)^2 \qquad P_2 = P_1\left(\frac{N_2}{N_1}\right)^3 Q 2 = Q 1 ( N 1 N 2 ) H 2 = H 1 ( N 1 N 2 ) 2 P 2 = P 1 ( N 1 N 2 ) 3
Flow varies directly with speed, head with the square, and power with the cube . This cubic relationship is why variable frequency drives save so much energy: dropping to 80% speed cuts power to about 51%.
Routine Maintenance
Item Task
Packing (stuffing box) Should drip slowly, roughly 30 to 60 drops per minute, to lubricate and cool. A packed gland that is bone dry is over-tightened and will score the shaft sleeve
Mechanical seals Should not leak at all; any visible leakage means seal failure
Bearings Lubricate on schedule; monitor temperature and vibration; over-greasing is as damaging as under-greasing
- Coupling alignment Check with dial indicator or laser; misalignment destroys bearings and seals
- Vibration analysis Trending identifies imbalance, misalignment, looseness, and bearing wear before failure
- Suction strainer Clean; monitor differential
- Motor Amperage draw trending, insulation resistance testing, ventilation, cleanliness
Rising amperage at constant flow and head signals mechanical binding or a failing bearing. Falling flow at constant speed signals impeller wear, a partially blocked suction, or an increase in system head.