Study guide

Heat, Cold, Extreme Climate, and Biological Hazard Controls

BCSP CHST Construction Health and Safety Technician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: CHST Exam Orientation and Official Source Control

Official Sources and Credential Purpose Eligibility, Application, Fees, and Character Review Exam Format, Scoring, Beta Questions, and Blueprint Pearson VUE Scheduling, Test Day, Results, and Retakes Blueprint-Based Study Plan and Readiness

2 Chapter 2: Hazard and Risk Identification Methods, JHA, and Controls

Hierarchy of Controls and Construction Risk Logic Job Hazard Analysis and Pre-Task Planning Risk Ranking, Severity, Frequency, and Corrective Action Safety Through Design and Construction Means and Methods PPE Selection, Limitations, and Basic Monitoring Instruments Multi-Trade Coordination, Simultaneous Operations, and Interface Risk Field Observation, Documentation, and Control Verification

3 Chapter 3: High-Hazard Construction Operations I - Fall, Electrical, Excavation, Confined Space, Hot Work, Tools, and Concrete

Working at Heights: Ladders, Scaffolds, and Leading Edge Exposures Fall Protection: Arrest, Restraint, and Rescue Planning Excavation and Trenching: Soil, Protection, and Access/Egress Electrical Hazards: Temporary Power, GFCI, and LOTO Awareness Confined Space Recognition, Atmospheric Testing, and Entry Controls Hot Work: Fire Watch, Combustibles, and Permit Controls Hand and Power Tools, Powder-Actuated Tools, and Concrete Work

4 Chapter 4: High-Hazard Construction Operations II - Struck-By, Equipment, Hoisting, Rigging, Cranes, Material Handling, and Storage

Struck-By, Caught-Between, and Line-of-Fire Controls Mechanized Equipment, Mobile Equipment, and Traffic Control Hoisting, Rigging, Sling Inspection, and Load Control Crane Operations, Critical Lifts, Signaling, and Exclusion Zones Material Handling, Storage, Stacking, and Housekeeping Concrete Placement, Formwork, Rebar, and Impalement Controls Simultaneous Operations, Sequencing, and Stop-Work Decisions

5 Chapter 5: Construction Health, Environmental, Chemical, and Ergonomic Exposure Controls

Silica, Asbestos, Lead, Heavy Metals, and Dust Controls Noise, Vibration, Radiation, and Impact Exposure Control Chemical Exposure, GHS, SDS, and HazCom Field Use Heat, Cold, Extreme Climate, and Biological Hazard Controls Ergonomics, Manual Material Handling, and Work Practice Design Exposure Monitoring, PPE Limitations, and Medical Referral Triggers

6 Chapter 6: Emergency Preparedness, Incident Investigation, and Response

Emergency Action Plans, Site Mitigation, and Evacuation Fire Protection, Prevention, Hot Work, and Alarm Response Environmental Contamination, Spill Response, and Notifications Incident Command, Crisis Management, and Emergency Equipment First Aid, Medical Needs, Bloodborne Pathogens, and Universal Precautions Incident Investigation, Near Misses, Root Cause, and Corrective Action Drills, After-Action Reviews, and Return to Operations

7 Chapter 7: Safety Program Development, Implementation, and Sustainment

Site-Specific Safety Plans and Relevant Program Selection Applying Standards, Regulatory Authority, and Role Boundaries Inspections, Audits, Observations, and Corrective Action Tracking Equipment Manuals, Manufacturer Directives, and Field Compliance Risk Management, Data Gathering, Recordkeeping, and Document Control Incident Causation, Post-Incident Reporting, and Follow-Up Trends, Leading Indicators, and Program Sustainment

8 Chapter 8: Leadership, Communication, Training, and Total Worker Health

Safety Leadership, Credibility, and Field Influence Communication Strategy, Crew Briefings, and Conflict Management Training Needs, Task Analysis, and Adult Learning Delivery Toolbox Talks, Competency Verification, and Documentation Consulting Manufacturers, Suppliers, and Subject Matter Experts Confidentiality, Ethics, Document Control, and Current Information Total Worker Health, At-Risk Behavior, and Risk Reduction Activities

9 Chapter 9: Mixed CHST Construction Case Labs

Fall Protection, Scaffold, and Rescue Case Lab Excavation, Confined Space, and Atmospheric Hazard Case Lab Crane, Rigging, Equipment, and Struck-By Case Lab Hot Work, Fire, and HazCom Case Lab Silica, Noise, Heat, and Health Exposure Case Lab Incident Investigation, Program Failure, and Corrective Action Case Lab Superintendent Meeting, Training, and Stop-Work Case Lab

10 Chapter 10: Standards, References, Ethics, and Field Application

OSHA 1926 Navigation and Construction Standard Application Competent Person, Qualified Person, and Authority Boundaries Consensus Standards, Manufacturer Instructions, and Equipment Manuals BCSP Code of Ethics, Confidentiality, and Professional Conduct Exam-Style Reference Use and Best Answer Strategy

11 Chapter 11: Final Review, High-Yield Tables, and CHST Exam-Day Readiness

Blueprint Quick Reference and Domain Triage High-Yield Construction Hazard Control Tables Emergency Program Leadership and Documentation Review Final Week Practice Plan, Error Log, and Pacing Final 48 Hours, Pearson VUE Test Day, and Retake Planning

Heat, Cold, Extreme Climate, and Biological Hazard Controls

Key Takeaways Explain This Topic AI

Heat illness risk depends on workload, clothing, humidity, radiant heat, hydration, acclimatization, and medical factors; heat stroke is a true emergency.

OSHA's acclimatization rule of thumb: new workers start at 20% of normal duration and increase ~20% per day; returning workers ramp over several days.

Cold stress can occur above freezing when workers are wet or wind-exposed; confusion plus shivering signals possible hypothermia.

Biological hazards (sewage, mold, bloodborne pathogens, bird/bat droppings, ticks) are governed in part by the Bloodborne Pathogens standard, 29 CFR 1910.1030.

Escalate immediately for heat stroke signs, hypothermia, frostbite, uncontrolled sewage, extensive mold, sharps injuries, or symptoms after biological exposure.

Last updated: June 2026

  • Heat, Cold, Extreme Climate, and Biological Hazard Controls
  • Heat illness and acclimatization

Heat exposure is more than weather. Workload, radiant heat, humidity, direct sun, air movement, protective clothing, respirators, hydration, acclimatization, medications, alcohol, and recent illness all raise risk. New workers, returning workers, and anyone assigned heavy work after time off are most vulnerable because the body needs days to adapt.

Heat disorders run from heat rash and cramps to heat exhaustion and heat stroke . Warning signs include heavy sweating, weakness, dizziness, headache, nausea, and - the red flags - confusion, loss of coordination, collapse, and hot, dry skin . Heat stroke is a medical emergency: call EMS, begin aggressive cooling, and do not wait for a perfect diagnosis when a worker shows altered mental status.

A testable rule is OSHA's acclimatization guidance for the "Rule of 20%": for new workers, begin at no more than 20% of the normal work duration on day one and add about 20% each day ; for workers returning after a week or more away, ramp up over at least four days (commonly 50%, 60%, 80%, 100%). Controls include scheduling heavy work for cooler periods, shade, mandatory rest/water cycles, mechanical assistance, reduced pace, buddy systems, cooling areas, and emergency planning. The heat index is a useful trigger tool: caution rises sharply above roughly 91 degrees F and danger above about 103 degrees F.

  • Condition Risk factor Useful control
  • Hot, humid work Poor sweat evaporation Rest, shade, water, acclimatization ramp
  • Radiant heat Sun, roofing, hot equipment Barriers, scheduling, cooling breaks
  • Encapsulating PPE Reduced heat loss Shorter cycles, cooling, medical review
  • Wildfire smoke Fine particles (PM2.5), gases Air-quality (AQI) review, relocation, respirators
  • Cold, storms, and environmental extremes

Cold stress can occur above freezing when workers are wet, wind-exposed, fatigued, or touching cold surfaces. Wind chill, not air temperature alone, drives frostbite risk. Outcomes include hypothermia, frostbite, trench foot, and reduced dexterity. Confusion plus shivering, clumsiness, slurred speech, or pale, waxy skin signals possible hypothermia - remove the worker from exposure, warm gradually, and get medical evaluation. Controls: layered clothing, wind protection, dry gloves and socks, heated break shelters, warm fluids, and task rotation. Extreme weather also includes lightning (the 30-30 rule: seek shelter at 30 seconds between flash and thunder, wait 30 minutes after the last thunder), high wind that grounds crane and lift operations, flooding, and ice. Field plans must name who monitors weather, the thresholds that change work, where workers shelter, and how to communicate if power or cellular service fails.

Biological hazards and the Bloodborne Pathogens standard

Biological hazards appear during demolition, renovation, utility work, disaster response, wastewater work, landscaping, and excavation. Sources include sewage, blood and other potentially infectious materials (OPIM), used needles, mold, bird and bat droppings (Histoplasma, Cryptococcus risk), rodents and ticks, contaminated soil, and stagnant water (Legionella in cooling towers). The Bloodborne Pathogens standard, 29 CFR 1910.1030 , applies when occupational exposure to blood or OPIM is reasonably anticipated, requiring an exposure control plan, hepatitis B vaccination offered within 10 working days of assignment, engineering and work-practice controls, and post-exposure evaluation and follow-up after a sharps injury.

Controls focus on avoiding contact, containing contamination, and preventing transfer: isolation, restricted access, wet methods, HEPA vacuuming, negative-pressure containment for significant mold work, puncture-resistant sharps containers , handwashing facilities, and decontamination. Never use compressed air to clean contaminated dust from clothing. PPE may include gloves, goggles, face shields, coveralls, boots, cut-resistant gloves for sharps, and respirators; it must be doffed without self-contamination. Workers need instruction on hand hygiene, wound covering, and reporting bites, needle sticks, sewage contact, rashes, or fever.

Documentation and escalation

Document heat and cold plans, weather monitoring, water and rest provisions, acclimatization ramps, biological hazard assessments, cleanup methods, waste disposal, and medical referrals. Escalate immediately for suspected heat stroke, hypothermia, frostbite, lightning exposure, uncontrolled sewage, extensive mold, unknown infectious material, needle sticks, animal bites, or symptoms after biological exposure. The CHST makes sure the emergency plan is active, not merely written.

Distinguishing heat exhaustion from heat stroke

The exam reliably tests the difference between heat exhaustion and heat stroke because the response is radically different. Heat exhaustion presents with heavy sweating, cool and clammy skin, weakness, nausea, headache, and a normal or slightly elevated mental state; the worker is still oriented. The response is to move the worker to shade, give cool water, loosen clothing, and monitor. Heat stroke presents with altered mental status, confusion, slurred speech, seizures, or collapse , and skin that may be hot and either dry or sweaty; core temperature is dangerously high. The response is to call EMS immediately and cool aggressively (cold water immersion or ice packs to the neck, armpits, and groin) - water alone is not enough and waiting is fatal. A trap answer offers "give the worker a drink and let them rest" for what the scenario describes as confusion and collapse; that is the heat-exhaustion response misapplied to a heat-stroke emergency.

Worked scenario: floodwater utility repair

A crew enters a flooded vault to repair a utility line. The water is sewage-contaminated, the air is humid, and there is mold on the walls. The CHST layers controls across all three hazard families. For biological exposure, the work meets the conditions for the Bloodborne Pathogens program if blood or OPIM are anticipated, so the exposure control plan, hepatitis B vaccination offer, and post-exposure follow-up apply; gloves, boots, eye protection, and respirators are selected, and no compressed air is used to clean contaminated surfaces. For heat, encapsulating PPE traps heat, so work cycles shorten, water and shade are staged, and the acclimatization ramp applies to anyone new to the task. For the confined, flooded space, atmospheric testing precedes entry. The lesson the exam reinforces is that real construction exposures rarely arrive one at a time, and the CHST must integrate climate, biological, and atmospheric controls into a single plan rather than solving only the most obvious hazard.