Study guide

Electrical Hazards: Temporary Power, GFCI, and LOTO Awareness

BCSP CHST Construction Health and Safety Technician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: CHST Exam Orientation and Official Source Control

Official Sources and Credential Purpose Eligibility, Application, Fees, and Character Review Exam Format, Scoring, Beta Questions, and Blueprint Pearson VUE Scheduling, Test Day, Results, and Retakes Blueprint-Based Study Plan and Readiness

2 Chapter 2: Hazard and Risk Identification Methods, JHA, and Controls

Hierarchy of Controls and Construction Risk Logic Job Hazard Analysis and Pre-Task Planning Risk Ranking, Severity, Frequency, and Corrective Action Safety Through Design and Construction Means and Methods PPE Selection, Limitations, and Basic Monitoring Instruments Multi-Trade Coordination, Simultaneous Operations, and Interface Risk Field Observation, Documentation, and Control Verification

3 Chapter 3: High-Hazard Construction Operations I - Fall, Electrical, Excavation, Confined Space, Hot Work, Tools, and Concrete

Working at Heights: Ladders, Scaffolds, and Leading Edge Exposures Fall Protection: Arrest, Restraint, and Rescue Planning Excavation and Trenching: Soil, Protection, and Access/Egress Electrical Hazards: Temporary Power, GFCI, and LOTO Awareness Confined Space Recognition, Atmospheric Testing, and Entry Controls Hot Work: Fire Watch, Combustibles, and Permit Controls Hand and Power Tools, Powder-Actuated Tools, and Concrete Work

4 Chapter 4: High-Hazard Construction Operations II - Struck-By, Equipment, Hoisting, Rigging, Cranes, Material Handling, and Storage

Struck-By, Caught-Between, and Line-of-Fire Controls Mechanized Equipment, Mobile Equipment, and Traffic Control Hoisting, Rigging, Sling Inspection, and Load Control Crane Operations, Critical Lifts, Signaling, and Exclusion Zones Material Handling, Storage, Stacking, and Housekeeping Concrete Placement, Formwork, Rebar, and Impalement Controls Simultaneous Operations, Sequencing, and Stop-Work Decisions

5 Chapter 5: Construction Health, Environmental, Chemical, and Ergonomic Exposure Controls

Silica, Asbestos, Lead, Heavy Metals, and Dust Controls Noise, Vibration, Radiation, and Impact Exposure Control Chemical Exposure, GHS, SDS, and HazCom Field Use Heat, Cold, Extreme Climate, and Biological Hazard Controls Ergonomics, Manual Material Handling, and Work Practice Design Exposure Monitoring, PPE Limitations, and Medical Referral Triggers

6 Chapter 6: Emergency Preparedness, Incident Investigation, and Response

Emergency Action Plans, Site Mitigation, and Evacuation Fire Protection, Prevention, Hot Work, and Alarm Response Environmental Contamination, Spill Response, and Notifications Incident Command, Crisis Management, and Emergency Equipment First Aid, Medical Needs, Bloodborne Pathogens, and Universal Precautions Incident Investigation, Near Misses, Root Cause, and Corrective Action Drills, After-Action Reviews, and Return to Operations

7 Chapter 7: Safety Program Development, Implementation, and Sustainment

Site-Specific Safety Plans and Relevant Program Selection Applying Standards, Regulatory Authority, and Role Boundaries Inspections, Audits, Observations, and Corrective Action Tracking Equipment Manuals, Manufacturer Directives, and Field Compliance Risk Management, Data Gathering, Recordkeeping, and Document Control Incident Causation, Post-Incident Reporting, and Follow-Up Trends, Leading Indicators, and Program Sustainment

8 Chapter 8: Leadership, Communication, Training, and Total Worker Health

Safety Leadership, Credibility, and Field Influence Communication Strategy, Crew Briefings, and Conflict Management Training Needs, Task Analysis, and Adult Learning Delivery Toolbox Talks, Competency Verification, and Documentation Consulting Manufacturers, Suppliers, and Subject Matter Experts Confidentiality, Ethics, Document Control, and Current Information Total Worker Health, At-Risk Behavior, and Risk Reduction Activities

9 Chapter 9: Mixed CHST Construction Case Labs

Fall Protection, Scaffold, and Rescue Case Lab Excavation, Confined Space, and Atmospheric Hazard Case Lab Crane, Rigging, Equipment, and Struck-By Case Lab Hot Work, Fire, and HazCom Case Lab Silica, Noise, Heat, and Health Exposure Case Lab Incident Investigation, Program Failure, and Corrective Action Case Lab Superintendent Meeting, Training, and Stop-Work Case Lab

10 Chapter 10: Standards, References, Ethics, and Field Application

OSHA 1926 Navigation and Construction Standard Application Competent Person, Qualified Person, and Authority Boundaries Consensus Standards, Manufacturer Instructions, and Equipment Manuals BCSP Code of Ethics, Confidentiality, and Professional Conduct Exam-Style Reference Use and Best Answer Strategy

11 Chapter 11: Final Review, High-Yield Tables, and CHST Exam-Day Readiness

Blueprint Quick Reference and Domain Triage High-Yield Construction Hazard Control Tables Emergency Program Leadership and Documentation Review Final Week Practice Plan, Error Log, and Pacing Final 48 Hours, Pearson VUE Test Day, and Retake Planning

Electrical Hazards: Temporary Power, GFCI, and LOTO Awareness

Key Takeaways Explain This Topic AI

GFCI protection or an Assured Equipment Grounding Conductor Program is required for 120V, 15/20A receptacles used in construction; GFCIs trip at about 5 milliamps of imbalance.

Keep mechanized equipment such as concrete pumps at least 10 feet from overhead lines up to 50 kV (29 CFR 1926.600(a)(6)); cranes first apply Subpart CC's 20-foot check (50 feet over 350 kV, 1926.1409).

The general-industry LOTO standard, 29 CFR 1910.147, excludes construction; on construction sites 1926.417 requires deenergized circuits to be rendered inoperative and tagged, and a CHST must recognize stored energy and unexpected energization risks.

GFCI protection is not a repair: damaged cords, missing ground pins, and wet unlisted connections must be removed from service even when plugged into a GFCI.

Treat temporary power as live, moving infrastructure that changes as trades relocate cords, panels, and lighting.

Last updated: October 2026

Electrical Hazards on Construction Sites

Electrocution is one of OSHA's construction "Fatal Four" (now "Focus Four"), so the CHST exam tests temporary power, GFCI, overhead lines, and lockout/tagout. The CHST does not act as an electrician; the field role is to spot shock, burn, arc-flash, fire, and unexpected-energization hazards early enough for qualified or authorized workers to correct them. Remember that as little as 0.1 ampere (100 mA) through the body can be fatal, while a GFCI senses imbalance and trips at roughly 5 mA within about 1/40 of a second.

Temporary Power and Cord Management

Panels need covers, clear working space (generally 3 feet in front of a 120/240V panel), labeling, weather protection, and protection from physical damage. Cords must be the three-wire, hard-service or junior-hard-service type rated for the use, routed away from sharp edges and vehicle paths, protected from water, and kept out of pinch points. Splices outside fittings, missing ground pins, crushed insulation, exposed conductors, and taped-over damage are removal-from-service conditions.

  • Condition Field Concern Practical Action
  • Cord across roadway Crushing, insulation damage Elevate, reroute, or protect
  • Open panel space Contact with energized parts Secure cover, restrict access
  • Wet cord connection Shock and fault path Use listed weather protection
  • Daisy-chained strips Overload and fire Provide proper distribution
  • GFCI Protection and the AEGCP Option

Under 29 CFR 1926.404, the employer must protect workers using 120-volt, single-phase, 15- and 20-ampere receptacle outlets that are not part of the permanent wiring through one of two routes: ground-fault circuit interrupters (GFCIs) on all such receptacles, or a documented Assured Equipment Grounding Conductor Program (AEGCP) with continuity and terminal testing on a defined schedule. The CHST must know which route the site uses and verify it is followed. GFCI protection is essential for cord-connected tools, wet locations, outdoor work, concrete cutting, pumps, and temporary lighting, but it is not a repair method.

A damaged cord, cracked tool housing, missing strain relief, or wet unlisted connection is removed from service even if plugged into a GFCI. A GFCI that repeatedly trips is reporting a real fault and must never be bypassed.

Overhead and Underground Hazards

Overhead power lines threaten cranes, concrete pumps, dump trucks, aerial lifts, ladders, and long material. For mechanized equipment covered by Subpart O, such as concrete pumps, 29 CFR 1926.600(a)(6) sets a minimum clearance of 10 feet from lines rated 50 kV or less, plus 0.4 inch for each 1 kV over 50 kV (about 4 inches per 10 kV). Cranes and derricks follow Subpart CC instead: if any part of the equipment, load line or load could get within 20 feet of a line (50 feet if the line is over 350 kV up to 1,000 kV, 29 CFR 1926.1409), the employer must have the line de-energized and grounded, keep that 20-foot (or 50-foot) distance with encroachment precautions, or keep the Table A distance for the voltage (10 feet up to 50 kV) with those precautions (29 CFR 1926.1408). Establish clearances, barricades, spotters, and utility de-energization or insulation where needed, and stay alert to boom swing and load drift during normal operation, not just when parked. Underground utilities create electrical hazards during excavation, drilling, sawcutting, and driving ground rods; locate conservatively and stop when an unmarked conduit is found.

LOTO Awareness

Lockout/tagout (LOTO) in general industry is governed by 29 CFR 1910.147, which states that it does not cover construction employment (1910.147(a)(1)(ii)(A)). On construction sites, 29 CFR 1926.417 requires controls that are deactivated during work to be tagged and deenergized equipment or circuits to be rendered inoperative and tagged at all points where they can be energized, and 1926.20(b)(3) requires noncompliant machinery or equipment to be tagged or locked out of use, or removed. Many contractors still run written energy-control procedures carried out by authorized employees ; a CHST applies locks only if trained and assigned, but must recognize when energy control is needed. Examples: maintenance on conveyors, pumps, mixers, crushers, temporary elevators, HVAC, panels, and powered gates. Stored energy lingers in capacitors, hydraulic and pneumatic systems, springs, gravity-loaded parts, and rotating components, so verification of zero energy is mandatory before work. Awareness questions:

Could equipment start while someone is servicing it?

Is there stored pressure, elevated material, or gravity energy?

Are multiple trades sharing the same disconnect or panel?

Has zero energy been verified by the authorized worker?

Are tags being used only as communication, or as part of a real lockout?

Approach Boundaries and Arc Flash

For work on or near exposed energized parts, the CHST should recognize the NFPA 70E approach boundaries : the limited approach boundary , the restricted approach boundary (which requires a qualified person and an energized work permit to cross), and the arc flash boundary , inside which arc-rated PPE is required to limit incident energy to a survivable 1.2 calories per square centimeter at the boundary.

Construction sites usually de-energize and lock out rather than work hot, but live troubleshooting, energized panel work, and connecting temporary service are exceptions that demand qualified workers, an energized electrical work permit, and arc-rated clothing. Recognizing that an unqualified worker is too close to an energized bus is a core CHST observation.

Bonding, Grounding, and Generators

Temporary generators are a frequent source of confusion. A portable generator powering only cord-and-plug equipment plugged directly into its receptacles may use the frame as the grounding reference (a bonded neutral) and does not require a separate driven ground rod, but once the generator feeds a structure's wiring through a transfer switch it becomes a separately derived system that must be grounded per the National Electrical Code. The CHST should verify that the site follows the manufacturer and a qualified electrician's guidance rather than improvising ground rods or defeating the bonding jumper.

Backfeeding a building through a dryer outlet or a male-to-male cord (a "suicide cord") is a serious hazard that can energize utility lines and kill linemen.

Electrical controls work only when the site treats power as a managed system. Trace the full path: source, panel, breaker, distribution, cord, connection, GFCI, tool, environment, and worker task. Weakness at any point can create a serious exposure.