Study guide
Fall Protection: Arrest, Restraint, and Rescue Planning
BCSP CHST Construction Health and Safety Technician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: CHST Exam Orientation and Official Source Control
Official Sources and Credential Purpose Eligibility, Application, Fees, and Character Review Exam Format, Scoring, Beta Questions, and Blueprint Pearson VUE Scheduling, Test Day, Results, and Retakes Blueprint-Based Study Plan and Readiness
2 Chapter 2: Hazard and Risk Identification Methods, JHA, and Controls
Hierarchy of Controls and Construction Risk Logic Job Hazard Analysis and Pre-Task Planning Risk Ranking, Severity, Frequency, and Corrective Action Safety Through Design and Construction Means and Methods PPE Selection, Limitations, and Basic Monitoring Instruments Multi-Trade Coordination, Simultaneous Operations, and Interface Risk Field Observation, Documentation, and Control Verification
3 Chapter 3: High-Hazard Construction Operations I - Fall, Electrical, Excavation, Confined Space, Hot Work, Tools, and Concrete
Working at Heights: Ladders, Scaffolds, and Leading Edge Exposures Fall Protection: Arrest, Restraint, and Rescue Planning Excavation and Trenching: Soil, Protection, and Access/Egress Electrical Hazards: Temporary Power, GFCI, and LOTO Awareness Confined Space Recognition, Atmospheric Testing, and Entry Controls Hot Work: Fire Watch, Combustibles, and Permit Controls Hand and Power Tools, Powder-Actuated Tools, and Concrete Work
4 Chapter 4: High-Hazard Construction Operations II - Struck-By, Equipment, Hoisting, Rigging, Cranes, Material Handling, and Storage
Struck-By, Caught-Between, and Line-of-Fire Controls Mechanized Equipment, Mobile Equipment, and Traffic Control Hoisting, Rigging, Sling Inspection, and Load Control Crane Operations, Critical Lifts, Signaling, and Exclusion Zones Material Handling, Storage, Stacking, and Housekeeping Concrete Placement, Formwork, Rebar, and Impalement Controls Simultaneous Operations, Sequencing, and Stop-Work Decisions
5 Chapter 5: Construction Health, Environmental, Chemical, and Ergonomic Exposure Controls
Silica, Asbestos, Lead, Heavy Metals, and Dust Controls Noise, Vibration, Radiation, and Impact Exposure Control Chemical Exposure, GHS, SDS, and HazCom Field Use Heat, Cold, Extreme Climate, and Biological Hazard Controls Ergonomics, Manual Material Handling, and Work Practice Design Exposure Monitoring, PPE Limitations, and Medical Referral Triggers
6 Chapter 6: Emergency Preparedness, Incident Investigation, and Response
Emergency Action Plans, Site Mitigation, and Evacuation Fire Protection, Prevention, Hot Work, and Alarm Response Environmental Contamination, Spill Response, and Notifications Incident Command, Crisis Management, and Emergency Equipment First Aid, Medical Needs, Bloodborne Pathogens, and Universal Precautions Incident Investigation, Near Misses, Root Cause, and Corrective Action Drills, After-Action Reviews, and Return to Operations
7 Chapter 7: Safety Program Development, Implementation, and Sustainment
Site-Specific Safety Plans and Relevant Program Selection Applying Standards, Regulatory Authority, and Role Boundaries Inspections, Audits, Observations, and Corrective Action Tracking Equipment Manuals, Manufacturer Directives, and Field Compliance Risk Management, Data Gathering, Recordkeeping, and Document Control Incident Causation, Post-Incident Reporting, and Follow-Up Trends, Leading Indicators, and Program Sustainment
8 Chapter 8: Leadership, Communication, Training, and Total Worker Health
Safety Leadership, Credibility, and Field Influence Communication Strategy, Crew Briefings, and Conflict Management Training Needs, Task Analysis, and Adult Learning Delivery Toolbox Talks, Competency Verification, and Documentation Consulting Manufacturers, Suppliers, and Subject Matter Experts Confidentiality, Ethics, Document Control, and Current Information Total Worker Health, At-Risk Behavior, and Risk Reduction Activities
9 Chapter 9: Mixed CHST Construction Case Labs
Fall Protection, Scaffold, and Rescue Case Lab Excavation, Confined Space, and Atmospheric Hazard Case Lab Crane, Rigging, Equipment, and Struck-By Case Lab Hot Work, Fire, and HazCom Case Lab Silica, Noise, Heat, and Health Exposure Case Lab Incident Investigation, Program Failure, and Corrective Action Case Lab Superintendent Meeting, Training, and Stop-Work Case Lab
10 Chapter 10: Standards, References, Ethics, and Field Application
OSHA 1926 Navigation and Construction Standard Application Competent Person, Qualified Person, and Authority Boundaries Consensus Standards, Manufacturer Instructions, and Equipment Manuals BCSP Code of Ethics, Confidentiality, and Professional Conduct Exam-Style Reference Use and Best Answer Strategy
11 Chapter 11: Final Review, High-Yield Tables, and CHST Exam-Day Readiness
Blueprint Quick Reference and Domain Triage High-Yield Construction Hazard Control Tables Emergency Program Leadership and Documentation Review Final Week Practice Plan, Error Log, and Pacing Final 48 Hours, Pearson VUE Test Day, and Retake Planning
Fall Protection: Arrest, Restraint, and Rescue Planning
Key Takeaways Explain This Topic AI
Fall restraint prevents reaching the edge; fall arrest accepts a fall and must stop it without contact with a lower level, so the two are designed differently.
A personal fall arrest system limits arresting force to 1,800 lbf, free fall to 6 feet, and deceleration distance to 3.5 feet, with anchors at 5,000 lbf or a 2:1 design factor.
Required fall clearance must add free fall, deceleration, harness stretch, D-ring shift, worker height, and a safety margin; swing fall must also be checked.
A rescue plan must retrieve a suspended worker promptly to prevent suspension trauma, not just call 911.
Inspect harnesses and connectors before each use and remove any system involved in a fall from service.
Last updated: June 2026
Fall Protection Systems and Field Decisions
Fall protection is a set of choices that must fit the surface, edge distance, anchor availability, fall clearance, rescue capability, and crew movement. The CHST should push the team up the hierarchy of controls : eliminate the exposure, then guard it passively, then restrain, and only then arrest. Passive guardrails and covers protect everyone in the area and do not depend on each worker clipping to the right point every time, which is why they outrank personal systems on the exam.
Restraint Versus Arrest
The best control keeps the worker away from the hazard. Fall restraint uses a lanyard length and anchor location that physically stop the worker before the edge. If a 6-foot lanyard lets the worker step past the edge, it is not restraint. Personal fall arrest is different: it accepts that a fall may occur and depends on the system stopping it before the worker strikes a lower level, structure, equipment, or stored material.
- Control Type Field Strength Field Weakness
- Guardrail Protects everyone in the area Removed for access or material handling
- Cover Controls holes and skylights Must be secured, marked, load-rated 2x
- Restraint Prevents edge access Requires correct length and anchor location
- Arrest Allows mobility Requires clearance, rescue, compatible parts
- Arrest System Specifications to Recall
A personal fall arrest system normally includes an anchorage, connectors, a full-body harness, and a lanyard or self-retracting lifeline (SRL). Memorize the OSHA 1926.502(d) limits, which are frequent exam items:
Maximum arresting force on the body: 1,800 lbf with a shock-absorbing lanyard and full-body harness.
Maximum free fall : 6 feet, and never contact a lower level.
Maximum deceleration distance : 3.5 feet.
Anchorage : capable of 5,000 lb per worker, or designed with a safety factor of at least 2 under the supervision of a qualified person.
Body belts are prohibited for arrest; only full-body harnesses are allowed.
Clearance is the most missed calculation. Required fall clearance = lanyard length + deceleration distance + harness stretch + D-ring shift + worker height + safety margin (commonly 2 to 3 feet). A 6-foot lanyard can easily need roughly 18.5 feet of clearance below the anchor before the worker can be safely arrested without striking the ground. Swing fall must also be checked: a worker anchored far to one side can swing into columns, rebar, or a lower structure even when vertical clearance seems adequate, and impact speed at the bottom of the arc can exceed the vertical fall.
Restraint, Positioning, and Inspection
Positioning devices support a worker on a vertical surface such as rebar assembly or formwork but limit free fall to 2 feet and may still require a separate arrest system. Inspect harnesses and connectors before each use for cuts, burns, chemical or paint contamination, missing labels, corrosion, deformation, pulled stitching, damaged buckles, and deployed shock packs. Any component involved in arresting a fall is removed from service until evaluated by a competent person. Storage matters: gear thrown into gang boxes with sharp tools, wet concrete, welding slag, or solvents can degrade unseen.
Rescue Planning
A rescue plan cannot be just "call 911." A suspended worker can develop suspension trauma (orthostatic intolerance) within minutes as blood pools in the legs, so prompt retrieval is essential. The plan identifies who responds, how they reach the worker, what equipment is staged, how the area is controlled, and how rescuers are themselves protected from the same fall hazard.
A good field rescue plan answers:
Can a lift, ladder, stair tower, or pre-staged rescue kit reach the suspended worker within minutes?
Who on this shift is trained and available?
How will the worker call for help if alone or out of sight?
What lower-level hazards must be cleared before work starts?
How will the system be preserved for incident review after rescue?
Connectors, Compatibility, and Anchorage
Component compatibility is a tested concept. Snap hooks must be self-closing and self-locking , and you must never connect two snap hooks to one D-ring or tie back a snap hook to its own lifeline unless the hook is rated for tie-back, because side loading or roll-out can let the gate open under load. Horizontal lifelines must be designed by a qualified person and maintained with a safety factor of at least 2. Anchorages used for arrest must support 5,000 pounds per attached worker or be designed by a qualified person to at least twice the maximum arresting force.
A pipe, conduit, small-diameter rebar, or a guardrail post is not an acceptable anchor unless engineered for the load; "it looks strong" is never the standard.
Self-Retracting Lifelines and Leading Edge SRLs
A self-retracting lifeline (SRL) reduces free fall by locking quickly, but a standard overhead SRL is not rated for foot-level or sharp-edge anchorage. Leading-edge work below the anchor requires a leading-edge-rated SRL (Class 2 / SRL-LE) with an energy absorber and an edge-tested lifeline, because a standard SRL's webbing or cable can be cut by a sharp edge or generate excessive arresting force at the edge. The CHST should verify the SRL class matches the application, that the lifeline retracts smoothly without hesitation, and that the load indicator has not deployed.
Fall protection succeeds when the crew can use it while doing real work. If the system forces repeated disconnection, climbing over lines, or work without enough clearance, the plan is incomplete and the CHST must catch the mismatch before exposure begins.