Study guide

Concrete Placement, Formwork, Rebar, and Impalement Controls

BCSP CHST Construction Health and Safety Technician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: CHST Exam Orientation and Official Source Control

Official Sources and Credential Purpose Eligibility, Application, Fees, and Character Review Exam Format, Scoring, Beta Questions, and Blueprint Pearson VUE Scheduling, Test Day, Results, and Retakes Blueprint-Based Study Plan and Readiness

2 Chapter 2: Hazard and Risk Identification Methods, JHA, and Controls

Hierarchy of Controls and Construction Risk Logic Job Hazard Analysis and Pre-Task Planning Risk Ranking, Severity, Frequency, and Corrective Action Safety Through Design and Construction Means and Methods PPE Selection, Limitations, and Basic Monitoring Instruments Multi-Trade Coordination, Simultaneous Operations, and Interface Risk Field Observation, Documentation, and Control Verification

3 Chapter 3: High-Hazard Construction Operations I - Fall, Electrical, Excavation, Confined Space, Hot Work, Tools, and Concrete

Working at Heights: Ladders, Scaffolds, and Leading Edge Exposures Fall Protection: Arrest, Restraint, and Rescue Planning Excavation and Trenching: Soil, Protection, and Access/Egress Electrical Hazards: Temporary Power, GFCI, and LOTO Awareness Confined Space Recognition, Atmospheric Testing, and Entry Controls Hot Work: Fire Watch, Combustibles, and Permit Controls Hand and Power Tools, Powder-Actuated Tools, and Concrete Work

4 Chapter 4: High-Hazard Construction Operations II - Struck-By, Equipment, Hoisting, Rigging, Cranes, Material Handling, and Storage

Struck-By, Caught-Between, and Line-of-Fire Controls Mechanized Equipment, Mobile Equipment, and Traffic Control Hoisting, Rigging, Sling Inspection, and Load Control Crane Operations, Critical Lifts, Signaling, and Exclusion Zones Material Handling, Storage, Stacking, and Housekeeping Concrete Placement, Formwork, Rebar, and Impalement Controls Simultaneous Operations, Sequencing, and Stop-Work Decisions

5 Chapter 5: Construction Health, Environmental, Chemical, and Ergonomic Exposure Controls

Silica, Asbestos, Lead, Heavy Metals, and Dust Controls Noise, Vibration, Radiation, and Impact Exposure Control Chemical Exposure, GHS, SDS, and HazCom Field Use Heat, Cold, Extreme Climate, and Biological Hazard Controls Ergonomics, Manual Material Handling, and Work Practice Design Exposure Monitoring, PPE Limitations, and Medical Referral Triggers

6 Chapter 6: Emergency Preparedness, Incident Investigation, and Response

Emergency Action Plans, Site Mitigation, and Evacuation Fire Protection, Prevention, Hot Work, and Alarm Response Environmental Contamination, Spill Response, and Notifications Incident Command, Crisis Management, and Emergency Equipment First Aid, Medical Needs, Bloodborne Pathogens, and Universal Precautions Incident Investigation, Near Misses, Root Cause, and Corrective Action Drills, After-Action Reviews, and Return to Operations

7 Chapter 7: Safety Program Development, Implementation, and Sustainment

Site-Specific Safety Plans and Relevant Program Selection Applying Standards, Regulatory Authority, and Role Boundaries Inspections, Audits, Observations, and Corrective Action Tracking Equipment Manuals, Manufacturer Directives, and Field Compliance Risk Management, Data Gathering, Recordkeeping, and Document Control Incident Causation, Post-Incident Reporting, and Follow-Up Trends, Leading Indicators, and Program Sustainment

8 Chapter 8: Leadership, Communication, Training, and Total Worker Health

Safety Leadership, Credibility, and Field Influence Communication Strategy, Crew Briefings, and Conflict Management Training Needs, Task Analysis, and Adult Learning Delivery Toolbox Talks, Competency Verification, and Documentation Consulting Manufacturers, Suppliers, and Subject Matter Experts Confidentiality, Ethics, Document Control, and Current Information Total Worker Health, At-Risk Behavior, and Risk Reduction Activities

9 Chapter 9: Mixed CHST Construction Case Labs

Fall Protection, Scaffold, and Rescue Case Lab Excavation, Confined Space, and Atmospheric Hazard Case Lab Crane, Rigging, Equipment, and Struck-By Case Lab Hot Work, Fire, and HazCom Case Lab Silica, Noise, Heat, and Health Exposure Case Lab Incident Investigation, Program Failure, and Corrective Action Case Lab Superintendent Meeting, Training, and Stop-Work Case Lab

10 Chapter 10: Standards, References, Ethics, and Field Application

OSHA 1926 Navigation and Construction Standard Application Competent Person, Qualified Person, and Authority Boundaries Consensus Standards, Manufacturer Instructions, and Equipment Manuals BCSP Code of Ethics, Confidentiality, and Professional Conduct Exam-Style Reference Use and Best Answer Strategy

11 Chapter 11: Final Review, High-Yield Tables, and CHST Exam-Day Readiness

Blueprint Quick Reference and Domain Triage High-Yield Construction Hazard Control Tables Emergency Program Leadership and Documentation Review Final Week Practice Plan, Error Log, and Pacing Final 48 Hours, Pearson VUE Test Day, and Retake Planning

Concrete Placement, Formwork, Rebar, and Impalement Controls

Key Takeaways Explain This Topic AI

Concrete and masonry construction is governed by 29 CFR 1926 Subpart Q; formwork must be designed, inspected, and removed only on competent direction.

Vertical rebar and other projections require guarding to prevent impalement under 1926.701(b); ordinary mushroom caps may not be impalement-rated.

Wet concrete is highly alkaline (pH around 12-13) and causes chemical burns; cured-concrete cutting generates silica (PEL 50 ug/m3, AL 25).

Pump lines can whip when air enters or a blockage clears; keep workers clear of the discharge end and out from under suspended buckets.

Last updated: October 2026

Concrete Placement, Formwork, Rebar, and Impalement Controls

Concrete work looks routine because pours happen often, but the hazards are high-energy and time-sensitive. The controlling standard is 29 CFR 1926 Subpart Q (Concrete and Masonry Construction), with 1926.701 covering general requirements, 1926.703 covering formwork and shoring, and 1926.706 covering masonry walls. Wet concrete is heavy (about 150 lb per cubic foot, so a single cubic yard weighs roughly 4,000 lb), pump lines can whip, buckets swing, ready-mix trucks back through tight areas, and forms can fail.

The CHST views placement as one coordinated operation involving equipment, temporary works, access, communication, chemical protection, and rescue.

Pre-Pour Planning

Before placement, confirm the pour plan matches the field: truck routes, pump location, hose route, crane-bucket path, washout area, worker access, lighting, fall protection, rebar protection, and emergency access. Verify that workers know the placement sequence, the rate-of-placement limits that the formwork was designed for, the stop command, and who may pause the pour.

Ready-mix delivery creates traffic risk — trucks have blind spots, rotating drums, chutes, pinch points, and washout concerns; control backing with spotters or designated routes. Pump trucks need stable setup, full outrigger support, overhead clearance (including the 29 CFR 1926.600(a)(6) power-line clearance: 10 feet from lines up to 50 kV, plus 0.4 inch per kV above that), line inspection, and direct communication between the pump operator and the placement crew.

Pump Hose, Buckets, and Formwork

A concrete pump hose can whip violently if air enters the line, a blockage clears, or pressure surges. Workers must not straddle the hose, stand in front of the discharge, or wrap the hose around their body; the crew keeps controlled footing and keeps the hose away from edges and openings. Concrete buckets are suspended loads — use controlled lift paths, exclusion zones, clear signals, and landing methods that keep workers from under the bucket and out of pinch points; no riding buckets, and tag lines only from a clear position.

Formwork and shoring are temporary structures that must carry construction loads until the concrete is self-supporting. Under 1926.703 they must be designed by a qualified designer, erected and braced per drawings, inspected by a competent person, and not removed until the concrete has gained sufficient strength (often verified by job-cured cylinder tests or a strength schedule in the plan).

Issue Why it matters CHST response

Missing or loose form tie Lateral form pressure may exceed capacity Stop placement in that area until corrected

  • Soft base under a shore Settlement overloads adjacent supports Require correction before loading
  • Excessive pour rate Lateral pressure on forms rises Hold to design rate and competent direction
  • Early or unauthorized stripping Concrete may not yet carry the load Stop and get qualified review

Impalement, Chemical, and Silica Hazards

Vertical rebar , anchor bolts, dowels, and form stakes can impale a worker who trips or falls. Under 1926.701(b) , all protruding reinforcing steel onto and into which employees could fall must be guarded to eliminate the hazard of impalement . Note the exam trap: ordinary plastic mushroom caps provide scratch protection only and are not impalement-rated unless the manufacturer certifies them with a steel insert for fall heights. Effective controls include engineered troughs, wood/steel-reinforced covers, bending the bar over (where the design allows), or rated impalement caps.

Pay attention to rebar near ladders, edges, deck openings, and finishing routes; rebar mats also create trip and unstable-surface hazards, so provide planks or walkways.

Wet concrete is strongly alkaline ( pH about 12-13 ) and causes serious chemical (caustic) burns, especially when it gets inside boots or gloves and stays in contact — workers need protective gloves, boots, eye protection, and prompt washing; remove contaminated clothing. Cutting, grinding, or drilling cured concrete generates respirable crystalline silica , regulated by 29 CFR 1926.1153 at a permissible exposure limit (PEL) of 50 micrograms per cubic meter as an 8-hour TWA and an action level of 25 .

Control with Table 1 methods — wet cutting, local exhaust/HEPA vacuums, and respiratory protection where required — and never dry sweep silica dust.

Stop-Work and Exam Focus

Stop the pour when formwork shows distress, pump communication fails, a worker enters the bucket fall zone, rebar impalement hazards are unprotected, trucks back without control, or the pour rate exceeds the design. On the exam, choose controls that address the actual source : engineered temporary works, controlled equipment movement, exclusion zones, impalement-rated guarding, and exposure prevention. PPE supports the plan but never replaces form inspections, pump control, or guarded protruding steel.

Limited-Access and Lift-Slab Rules

Subpart Q includes two specifics the exam likes. First, limited-access zones : under 1926.706 a masonry wall over 8 feet tall must have a limited-access zone established before construction begins, on the unscaffolded side, equal to the wall height plus 4 feet, with entry restricted to the crew building the wall — and the wall must be braced against collapse until permanent supports are in place. Second, lift-slab operations under 1926.705 require an engineered plan and prohibit workers in the building while jacks lift the slabs, a rule written after fatal lift-slab collapses.

Also remember that no employee may be permitted to work under concrete buckets while they are being elevated or traveled (1926.701(e)), reinforcing the suspended-load exclusion zone for bucket pours.