Study guide
Struck-By, Caught-Between, and Line-of-Fire Controls
BCSP CHST Construction Health and Safety Technician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: CHST Exam Orientation and Official Source Control
Official Sources and Credential Purpose Eligibility, Application, Fees, and Character Review Exam Format, Scoring, Beta Questions, and Blueprint Pearson VUE Scheduling, Test Day, Results, and Retakes Blueprint-Based Study Plan and Readiness
2 Chapter 2: Hazard and Risk Identification Methods, JHA, and Controls
Hierarchy of Controls and Construction Risk Logic Job Hazard Analysis and Pre-Task Planning Risk Ranking, Severity, Frequency, and Corrective Action Safety Through Design and Construction Means and Methods PPE Selection, Limitations, and Basic Monitoring Instruments Multi-Trade Coordination, Simultaneous Operations, and Interface Risk Field Observation, Documentation, and Control Verification
3 Chapter 3: High-Hazard Construction Operations I - Fall, Electrical, Excavation, Confined Space, Hot Work, Tools, and Concrete
Working at Heights: Ladders, Scaffolds, and Leading Edge Exposures Fall Protection: Arrest, Restraint, and Rescue Planning Excavation and Trenching: Soil, Protection, and Access/Egress Electrical Hazards: Temporary Power, GFCI, and LOTO Awareness Confined Space Recognition, Atmospheric Testing, and Entry Controls Hot Work: Fire Watch, Combustibles, and Permit Controls Hand and Power Tools, Powder-Actuated Tools, and Concrete Work
4 Chapter 4: High-Hazard Construction Operations II - Struck-By, Equipment, Hoisting, Rigging, Cranes, Material Handling, and Storage
Struck-By, Caught-Between, and Line-of-Fire Controls Mechanized Equipment, Mobile Equipment, and Traffic Control Hoisting, Rigging, Sling Inspection, and Load Control Crane Operations, Critical Lifts, Signaling, and Exclusion Zones Material Handling, Storage, Stacking, and Housekeeping Concrete Placement, Formwork, Rebar, and Impalement Controls Simultaneous Operations, Sequencing, and Stop-Work Decisions
5 Chapter 5: Construction Health, Environmental, Chemical, and Ergonomic Exposure Controls
Silica, Asbestos, Lead, Heavy Metals, and Dust Controls Noise, Vibration, Radiation, and Impact Exposure Control Chemical Exposure, GHS, SDS, and HazCom Field Use Heat, Cold, Extreme Climate, and Biological Hazard Controls Ergonomics, Manual Material Handling, and Work Practice Design Exposure Monitoring, PPE Limitations, and Medical Referral Triggers
6 Chapter 6: Emergency Preparedness, Incident Investigation, and Response
Emergency Action Plans, Site Mitigation, and Evacuation Fire Protection, Prevention, Hot Work, and Alarm Response Environmental Contamination, Spill Response, and Notifications Incident Command, Crisis Management, and Emergency Equipment First Aid, Medical Needs, Bloodborne Pathogens, and Universal Precautions Incident Investigation, Near Misses, Root Cause, and Corrective Action Drills, After-Action Reviews, and Return to Operations
7 Chapter 7: Safety Program Development, Implementation, and Sustainment
Site-Specific Safety Plans and Relevant Program Selection Applying Standards, Regulatory Authority, and Role Boundaries Inspections, Audits, Observations, and Corrective Action Tracking Equipment Manuals, Manufacturer Directives, and Field Compliance Risk Management, Data Gathering, Recordkeeping, and Document Control Incident Causation, Post-Incident Reporting, and Follow-Up Trends, Leading Indicators, and Program Sustainment
8 Chapter 8: Leadership, Communication, Training, and Total Worker Health
Safety Leadership, Credibility, and Field Influence Communication Strategy, Crew Briefings, and Conflict Management Training Needs, Task Analysis, and Adult Learning Delivery Toolbox Talks, Competency Verification, and Documentation Consulting Manufacturers, Suppliers, and Subject Matter Experts Confidentiality, Ethics, Document Control, and Current Information Total Worker Health, At-Risk Behavior, and Risk Reduction Activities
9 Chapter 9: Mixed CHST Construction Case Labs
Fall Protection, Scaffold, and Rescue Case Lab Excavation, Confined Space, and Atmospheric Hazard Case Lab Crane, Rigging, Equipment, and Struck-By Case Lab Hot Work, Fire, and HazCom Case Lab Silica, Noise, Heat, and Health Exposure Case Lab Incident Investigation, Program Failure, and Corrective Action Case Lab Superintendent Meeting, Training, and Stop-Work Case Lab
10 Chapter 10: Standards, References, Ethics, and Field Application
OSHA 1926 Navigation and Construction Standard Application Competent Person, Qualified Person, and Authority Boundaries Consensus Standards, Manufacturer Instructions, and Equipment Manuals BCSP Code of Ethics, Confidentiality, and Professional Conduct Exam-Style Reference Use and Best Answer Strategy
11 Chapter 11: Final Review, High-Yield Tables, and CHST Exam-Day Readiness
Blueprint Quick Reference and Domain Triage High-Yield Construction Hazard Control Tables Emergency Program Leadership and Documentation Review Final Week Practice Plan, Error Log, and Pacing Final 48 Hours, Pearson VUE Test Day, and Retake Planning
Struck-By, Caught-Between, and Line-of-Fire Controls
Key Takeaways Explain This Topic AI
Struck-by and caught-between are two of OSHA's construction Focus Four hazards, together accounting for hundreds of construction deaths per year.
Line of fire is a dynamic exposure that changes whenever equipment, loads, stored energy, or sequencing changes.
Use the hierarchy of controls: eliminate the pinch point or separate workers before relying on PPE or worker attention.
Stop work whenever a worker can be pinned, crushed, or hit before anyone can react.
Last updated: November 2026
Struck-By, Caught-Between, and Line-of-Fire Controls
Struck-by and caught-between (caught-in-or-between) are two of OSHA's construction Focus Four hazards, alongside falls and electrocution. BLS counted falls, slips, and trips as 39.2 percent of the 1,075 construction deaths in 2023, with transportation incidents second at 22.3 percent. On the Construction Health and Safety Technician (CHST) exam these scenarios appear across both the Knowledge and Skills question categories, and the tested answer almost always applies the hierarchy of controls rather than PPE or a verbal warning.
Define the Exposure Precisely
The distinction matters for picking the right control. A struck-by injury occurs when a worker is hit by a moving object that retains its energy on impact (a swinging load, a rolling pipe, a flying nail). A caught-between injury occurs when the worker is squeezed, pinned, or crushed between two objects, or between a moving object and a fixed one. OSHA draws a useful test: if the impact alone caused the injury it is struck-by; if the crushing/squeezing caused it, it is caught-between.
Line of fire is the path an object, load, tool, vehicle, or released force will travel if control is lost. Ask not only what is moving now, but what could move if a sling slips, a chain breaks, a trench wall shifts, a tire rolls, a form panel kicks out, or a hydraulic line releases stored pressure.
A Field Scan in Four Energy Categories
Moving equipment — trucks, forklifts, loaders, excavators, compactors, telehandlers, skid steers; backing and swing radius are the top killers.
Moving loads — suspended picks, pushed material, rolling pipe, stacked bundles, buckets, forks, crane blocks.
Stored (released) energy — compressed air, hydraulic pressure, springs, gravity, tensioned cable, unstable soil; control through lockout/tagout (LOTO) and blocking before opening a system.
Dropped objects — hand tools, deck materials, formwork, scaffold parts, loose hardware; controlled with toeboards, debris nets, tool tethers, and barricaded drop zones.
Match the Barrier to the Force
- Exposure Practical Control CHST Verification
- Reversing truck Spotter + backup alarm + cleared route Spotter has eye contact and no other duty
- Suspended load Exclusion zone, tag line, no worker under load Zone covers full swing radius and landing area
- Rolling pipe / round stock Chocks, cribbing, racks Chocks fit the material and cannot kick out
- Flying particles Machine guarding + shields + eye/face PPE Adjacent and downrange workers also protected
Released hydraulic energy LOTO, bleed pressure, block raised parts Zero-energy state verified before hands enter
Separation is the preferred control. A soft cone line may suffice for pedestrian routing around low-risk storage, but it is never adequate where a worker could be hit by a swinging concrete bucket or a 4,000-pound counterweight — those require hard barricades or a controlled-access zone.
Positive Communication and Stop-Work Triggers
Vague phrases like "watch out" or "be careful" do not create control. Use positive communication : who is moving, where, who signals, what channel or hand signals are used, and what single command stops the work. For mobile equipment the spotter and operator agree on a stop signal before movement; if visual contact is lost, the equipment stops. This mirrors the crane rule that any worker may give an emergency stop signal.
Stop work immediately when: an exclusion zone is missing, a spotter is distracted or doing a second job, a worker walks under a suspended load, material is not secured against rolling or falling, a reversing path is shared with pedestrians, or two crews create crossing lines of fire.
CHST Field Decisions and the Exam
Challenge any plan that puts a worker in the pinch point to save time — guiding a load by its bottom edge, standing between a truck and a dock, reaching into a nip point to clear debris. The better decision is to redesign the task with push poles, tag lines (used from a clear position, never wrapped), remote-release devices, blocking, equipment repositioning, or sequencing changes.
On the CHST exam several options will sound reasonable. The best answer controls the hazard at the source or separates the worker before relying on PPE or attention. Hard hats, high-visibility garments, and safety glasses are required, but they never justify standing under a load, walking through a backing zone, or working inside a crush point. Inspection is your early-warning system: loose guardrails, damaged barricades, dead backup alarms, broken mirrors, or weak stack cribbing all signal that the struck-by system is failing.
Common Exam Traps
Watch three recurring distractors. First, options that add a second PPE layer (thicker gloves, another hard hat) when the worker is still in the line of fire — PPE sits at the bottom of the hierarchy of controls and never substitutes for elimination or separation. Second, options that slow the equipment instead of removing the exposure; a slower crush is still a crush. Third, options that add a verbal reminder or a sign where a physical barrier is required. A reliable rule: if a single failure — a slipped sling, a missed mirror, one distracted second — can still kill the worker, the control is too weak.
Pick the answer that removes the worker from the path or eliminates the released-energy source first.