Study guide

3.5 Site Research, Site Surveys, and Multi-Site Evaluation

BICSI DCDC Data Center Design Consultant

Track your progress as you read

Finished sections get a check mark.

1 Introduction

About the BICSI DCDC Exam (DCDC-004)

2 Chapter 1: Project Initiation & Design Requirements

1.1 Owner's Project Requirements (OPR) and Basis of Design (BOD) 1.2 Stakeholder Coordination and Needs Assessment 1.3 Applicable Codes, Standards, and Regulatory Frameworks

3 Chapter 2: Data Center Models & Reliability Classifications

2.1 Data Center Business Models: Enterprise, Colocation, Cloud, Edge, and Modular 2.2 ANSI/BICSI 002 Availability and Reliability Classifications (Class 0 through Class 4) 2.3 Comparative Reliability Frameworks: Uptime Institute Tiers and TIA-942 Ratings

4 Chapter 3: Site Selection & Environmental Feasibility

3.1 Geographic and Environmental Risk Assessment 3.2 Proximity Hazards, Flight Paths, EMF, and Vibration Analysis 3.3 Utility Infrastructure Assessment 3.4 Site Access, Zoning, Permitting, and Physical Boundary Constraints 3.5 Site Research, Site Surveys, and Multi-Site Evaluation 3.6 Site Selection Financial Analysis, Incentives, and the Feasibility Report

5 Chapter 4: Capacity Planning, Financial Modeling & Risk Assessment

4.1 IT Load Forecasting and Power/Cooling Density Projections 4.2 Financial Modeling: CapEx, OpEx, Total Cost of Ownership (TCO), and ROI 4.3 Efficiency Metrics: PUE, WUE, CUE, and Energy Star Benchmarking 4.4 Risk Assessment Methodologies: Single Points of Failure, Fault Trees, and Reliability Calculations

6 Chapter 5: Architectural Spaces & Structural Layout

5.1 Structural Requirements: Floor Loading, Ceiling Clearances, and Seismic Bracing 5.2 Data Center Spatial Allocation: Computer Room and Support Spaces 5.3 Raised Floor Systems, Airflow Management Tiles, Slab Floors, Ramps, and Airlock Vestibules 5.4 Personnel Requirements, Support Space Adjacencies, and Circulation

7 Chapter 6: Mechanical Cooling & Thermal Management

6.1 Heat Load Calculations: Sensible vs Latent Heat and Refrigeration Capacity 6.2 Cooling Technologies: DX, Chilled Water, Evaporative, and Economizers 6.3 Airflow Containment Strategies: Hot/Cold Aisle, CAC vs HAC, and Airflow Management 6.4 Environmental Criteria and Close-Coupled/Liquid Cooling: ASHRAE TC 9.9, In-Row, RDHx, and Liquid/Immersion

8 Chapter 7: Electrical Distribution & Power Conditioning

7.1 Utility Service Entrance, Transformers, Switchgear, and Transfer Switches 7.2 Standby and Emergency Generator Systems: Fuel Systems, Paralleling Switchgear, and Load Testing 7.3 Uninterruptible Power Supply Systems, Battery Chemistries, and Runtime Sizing 7.4 Power Distribution Architectures, Redundancy Topologies, and Earthing/Bonding

9 Chapter 8: IT Infrastructure & Network Topologies

8.1 Server, Compute, and Storage Architectures: EIA-310, Blade, and Hyperconverged Systems 8.2 Network Topologies: Traditional 3-Tier vs Spine-Leaf Clos Architecture 8.3 Switching Architectures: Top-of-Rack, Middle-of-Row, and End-of-Row

10 Chapter 9: Fire Protection & Building Automation Systems

9.1 Fire Detection Systems: High-Sensitivity Smoke Detection (HSSD/VESDA) and Multi-Criteria Sensing 9.2 Fire Suppression Systems: Clean Agents and Pre-Action Sprinklers 9.3 Room Integrity, Pressure Relief Venting, and Enclosure Testing 9.4 Building Automation Systems, Environmental Monitoring, and DCIM

11 Chapter 10: Communications Connectivity & Structured Cabling

10.1 Structured Cabling Standards and Functional Spaces per ANSI/BICSI 002 and TIA-942 10.2 Transmission Media: Balanced Twisted-Pair Copper and Optical Fiber 10.3 High-Density Optical Fiber Connectivity, Multi-Fiber Push-On (MPO/MTP), and Polarity Methods 10.4 Cable Pathways, Cable Trays, Fill Ratios, Bend Radius, and Separation from Power 10.5 Site Communications Requirements, Access Provider Diversity, and RCDD Coordination

12 Chapter 11: Operational Procedures & Maintenance Programs

11.1 Operational Documentation: Standard Operating Procedures, Methods of Procedure, and Emergency Operating Procedures 11.2 Change Management and Configuration Management Processes 11.3 Maintenance Strategies: Preventive, Predictive, and Corrective Maintenance 11.4 Data Center Assessments: Optimization Studies, Current-State Evaluation, and the Findings Report

13 Chapter 12: Capacity, Lifecycle & Safety Management

12.1 Continuous Capacity Management: Space, Power, Cooling, and Network Utilization 12.2 Equipment Lifecycle, Asset Tracking, and Decommissioning Workflows 12.3 Electrical Safety, Arc Flash Hazards (NFPA 70E), Lockout/Tagout, and Live Work

14 Chapter 13: Concentric Physical Security & Access Control

13.1 Layered Defense-in-Depth Architecture: Perimeter, Facility, Internal, Whitespace, and Cabinet Levels 13.2 Physical Barriers, Fencing, Gates, Bollards (ASTM Crash Ratings), and Vehicle Mitigation 13.3 Electronic Access Control Systems, Mantraps, Anti-Tailgating, and Biometric Authentication

15 Chapter 14: Surveillance, Threat Assessment & Disaster Recovery

14.1 Video Surveillance Systems: Camera Siting, Resolution, Lighting, and Retention Policies 14.2 Threat and Vulnerability Assessments, Insider Threat Mitigation, and Physical Security Audits 14.3 Disaster Recovery and Business Continuity: RPO, RTO, and Backup Site Topologies 14.4 Security Audits, Verification of Findings, Countermeasure Selection, and Cost-Benefit Analysis

16 Chapter 15: Construction Administration & Project Delivery

15.1 Project Delivery Methods and Procurement Strategies for Mission-Critical Facilities 15.2 Construction Administration: Submittal Reviews, Requests for Information, and Change Orders 15.3 Field Observation, Quality Assurance/Quality Control, Punch Lists, and Record Documentation

17 Chapter 16: Data Center Commissioning & Integrated Systems Testing

16.1 Commissioning Process, Standards, and Levels 1 through 3: Factory Testing to Component Startup 16.2 Level 4 Functional Performance Testing of Mechanical and Electrical Subsystems 16.3 Level 5 Integrated Systems Testing, Black Start, and Operational Turnover

3.5 Site Research, Site Surveys, and Multi-Site Evaluation

Key Takeaways Explain This Topic AI

ANSI/BICSI 002-2024 requires site suitability to be determined by a site survey and evaluation plus a risk analysis; an existing survey is acceptable only if under six months old.

Site research moves from desktop screening (GIS, flood, seismic, and utility maps) to a field survey and then to due diligence studies such as geotechnical borings and a Phase I ESA.

Separate pass/fail knockout criteria from weighted criteria so a fatal flaw, such as an unmitigable flood risk, cannot be averaged away by strong scores elsewhere.

A weighted site score is the sum of each criterion weight times its score; weights must total 100% and be agreed with the client before scoring.

Sensitivity testing that shifts the weights shows whether the recommended site stays first or whether the ranking depends on one debatable assumption.

Last updated: October 2026

3.5 Site Research, Site Surveys, and Multi-Site Evaluation

The DCDC blueprint asks the consultant to conduct site research or a survey to confirm topography, adjacent areas, and the comparison of multiple sites, and then to evaluate how well potential sites meet the criteria . The earlier sections of this chapter explain what makes a site good or bad (hazards, proximity, utilities, zoning). This section explains how the consultant gathers that evidence and turns it into a defensible comparison.

ANSI/BICSI 002-2024 sets the baseline: the suitability of a site shall be determined by a site survey and evaluation and by a risk analysis. An existing survey may be reused only if it is less than six months old , because land use, utility capacity, and neighboring development change quickly.

Stage 1: Desktop Research and Screening

Desktop research eliminates weak sites before anyone travels. Typical sources include:

GIS and internet mapping: aerial and street imagery, parcel boundaries, ownership, land use, and elevation contours. Survey tools such as handheld GPS and mapping software let the team record exact coordinates for every observation later.

Natural hazard data: flood maps (in the United States, FEMA's National Flood Hazard Layer), the ASCE Hazard Tool for site-specific wind, seismic, snow, and ice loads under ASCE 7, historical weather, wildfire history, and lightning flash density maps.

Proximity hazards: distances to airports and flight paths, railroads, highways, pipelines, chemical plants, and other hazards, screened against the BICSI 002 Table 5-1 distances (for example, 8 km from airports, 1.6 km from railroads, 80 km from nuclear plants).

Utilities and telecommunications: transmission and distribution maps, substation locations, utility service territories, water and sewer mains, gas pipelines, and fiber route maps from access providers.

Regulatory data: zoning maps, comprehensive plans, environmental databases, and airspace restrictions. In the United States, a structure or construction crane near an airport or taller than 200 ft above ground may require FAA notice under 14 CFR Part 77.

Stage 2: The Field Survey

A field survey confirms what the maps suggest and finds what they miss. The survey team typically:

Walks the site and records GPS-tagged photographs of boundaries, slopes, drainage, existing structures, and overhead lines.

Confirms topography: BICSI 002 recommends avoiding slopes steeper than 15% and sites above 3,050 m (10,000 ft) elevation; standing water and erosion show drainage problems.

Inventories adjacent areas: what is on every side of the parcel and what could be built there under current zoning. A quiet field today can be a truck terminal or quarry later.

Checks access: BICSI 002 recommends at least two access roads, each with at least 4.3 m (14 ft) of vertical clearance, and routes that stay above flood levels.

Locates utility points of connection: the nearest substation and feeders, water and sewer connections, and the poles or manholes where access providers would enter.

Notes nuisance sources: radio transmitters, rail lines, and heavy industry. BICSI 002 recommends measuring vibration and electromagnetic interference near railroads over several days, not in a single visit.

Meets local stakeholders: planning staff, utility account managers, and economic development officials, who can confirm capacity, schedules, and incentives.

Stage 3: Due Diligence Studies

For the short-listed sites, specialists prepare formal studies, usually while the client holds the land under an option or a contract with a due diligence period:

Study What it establishes

ALTA/NSPS land title survey Boundaries, easements, encroachments, and access rights tied to the title commitment

Topographic survey Contours, existing grades, and drainage paths for civil design and earthwork estimates

Geotechnical investigation Soil bearing capacity, groundwater depth, seismic site class, and liquefaction potential from borings

Phase I Environmental Site Assessment (ASTM E1527-21) Recognized environmental conditions from past uses; may lead to Phase II sampling

Utility capacity studies and will-serve letters Whether power, water, and sewer can serve the planned load, by what date, and at what cost

Access provider inquiries Which carriers can deliver diverse routes to the site, and the build cost

Wetlands, cultural resource, and traffic studies Permitting constraints that can shrink the buildable area or delay approvals

Multi-Site Evaluation: Knockouts, Weights, and Scores

Comparing sites is where many consultants lose credibility. A sound method has four parts.

1. Define criteria from the client's requirements. Use the needs assessment (capacity, availability class, growth, schedule, budget) and BICSI's site factors. Each criterion needs a written scoring rubric, such as "5 = two independent substations with capacity available within 18 months."

2. Apply knockout criteria first. Some conditions are pass/fail: inadequate power by the required date, an unmitigable flood risk, or zoning that cannot be changed. A site that fails a knockout is removed, no matter how well it scores elsewhere.

3. Weight and score the remaining criteria. Weights reflect client priorities and must total 100%. The weighted score is:

Site Score = ∑ i = 1 n ( w i × s i ) \text{Site Score} = \sum_{i=1}^{n} (w_i \times s_i) Site Score = ∑ i = 1 n ​ ( w i ​ × s i ​ )

where w i w_i w i ​ is the weight of criterion i i i and s i s_i s i ​ is the site's score on that criterion.

4. Test sensitivity. Shift the weights within a reasonable range and confirm whether the ranking changes.

Worked Example

Three sites survive the knockout screen. Scores use a 1-to-5 scale:

  • Criterion Weight Site A Site B Site C
  • Power availability and cost 30% 5 3 4
  • Telecommunications diversity 20% 3 5 4
  • Natural hazard exposure 20% 4 3 5
  • Land, zoning, and expansion room 15% 3 4 2
  • Labor, access, and logistics 15% 4 5 3
  • Weighted score 100% 3.95 3.85 3.75

Site A scores 5 ( 0.30 ) + 3 ( 0.20 ) + 4 ( 0.20 ) + 3 ( 0.15 ) + 4 ( 0.15 ) = 3.95 5(0.30) + 3(0.20) + 4(0.20) + 3(0.15) + 4(0.15) = 3.95 5 ( 0.30 ) + 3 ( 0.20 ) + 4 ( 0.20 ) + 3 ( 0.15 ) + 4 ( 0.15 ) = 3.95 .

Now test sensitivity. If the client decides telecommunications diversity matters more and shifts the weights to 20% power and 30% telecommunications, Site A falls to 3.75 and Site B rises to 4.05. The ranking flips. The report must show this, and the consultant should confirm the weights with the client before recommending a site. A recommendation that depends on one disputed weight is a decision for the client, not a fact for the consultant to assert.

Common Exam Traps & DCDC Pitfalls

Relying on an old survey: BICSI 002 accepts an existing site survey only if it is less than six months old.

Averaging away a fatal flaw: A site in a flood hazard area should fail a knockout screen, not lose a few weighted points.

Scoring before agreeing weights: Weights set after scores are known invite bias. Agree the criteria, rubrics, and weights with the client first.

Skipping the field visit: Maps rarely show a new neighbor under construction, a shared fiber bridge crossing, or poor drainage.

Confusing survey types: A topographic survey shows grades; an ALTA/NSPS survey shows boundaries and easements; a geotechnical investigation shows soil and groundwater conditions.

Loading diagram... Site Research and Multi-Site Evaluation Workflow