Study guide
3.3 Project Delivery Methods & Impact of Project Funding Sources
California Supplemental Examination CSE
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: California Architects Practice Act & Professional Practice
1.1 Licensing, Board Authority, and Unlicensed Practice Exceptions 1.2 Mandatory Written Contracts & Required Provisions 1.3 Architect's Stamp, Signature, and Professional Liability
2 Chapter 2: Professional Conduct, Ethics & Business Entities
2.1 Rules of Professional Conduct & Disciplinary Grounds 2.2 Permissible Business Entities, Firm Names, and Filing Requirements 2.3 Copyright, Instruments of Service & Ownership of Architectural Documents
3 Chapter 3: Contractual Roles, Scope & Consultant Agreements
3.1 Standard Owner-Architect Agreements (AIA B101 / B102) & California Practice Realities 3.2 Consultant Selection, Prime-Consultant Agreements & Liability Flow-Down (AIA C401) 3.3 Project Delivery Methods & Impact of Project Funding Sources
4 Chapter 4: Risk Management, Dispute Resolution & Project Planning
4.1 Professional Standard of Care & Managing Contractual Risk and Liability 4.2 Dispute Resolution in California Practice: Mediation, Arbitration, and Litigation 4.3 Project Scheduling, Budgeting Assumptions, and Milestone Approvals
5 Chapter 5: Site Feasibility, Schematic Design & Discretionary Approvals
5.1 Site Feasibility Studies, Existing-Conditions Due Diligence & Project Impacts 5.2 Programming, Schematic Design Development & Stakeholder Engagement 5.3 Local Land-Use Control: General Plans, Zoning, Specific Plans & Local Ordinances 5.4 The Discretionary Approval Process: Use Permits, Variances, Design Review & Hearings 5.5 Entitlement Exhibits, Conditions of Approval & Leading the Approval Team
6 Chapter 6: Environmental Review & CEQA Compliance
6.1 CEQA Regulatory Framework: Lead, Responsible, and Trustee Agencies 6.2 CEQA Process: Statutory & Categorical Exemptions, Initial Studies, and (Mitigated) Negative Declarations 6.3 Environmental Impact Reports (EIR) & Official Filings (NOP, NOC, NOD, NOE)
7 Chapter 7: California Coastal Act & Specialized Regional Regulations
7.1 California Coastal Commission & Coastal Development Permits (CDP) 7.2 Local Coastal Programs (LCP), Coastal Zone Boundaries, and Appeals 7.3 Clean Air Act (CARB/AQMDs) & Clean Water Regulations (Porter-Cologne, RWQCB & SWPPP)
8 Chapter 8: State Agency Jurisdictions: DSA, HCAI & Essential Services
8.1 Division of the State Architect (DSA): Field Act & Public K-12/Community College Oversight 8.2 Department of Health Care Access and Information (HCAI): Alfred E. Alquist Act & Healthcare Facility Classification 8.3 Essential Services Buildings Seismic Safety Act (ESBSSA) & California Historical Building Code (CHBC)
9 Chapter 9: California Building Code (CBC Title 24 Part 2) Core Architecture Provisions
9.1 Occupancy Classifications, Building Heights, and Allowable Floor Areas (CBC Chapters 3 & 5) 9.2 Fire and Smoke Protection Features, Fire Barriers, and Fire-Resistance Ratings (CBC Chapter 7) 9.3 Means of Egress, Occupant Load Calculations, and Exit Separation (CBC Chapter 10) 9.4 California Health and Safety Code: Building Standards Law, State Housing Law & Health Mandates
10 Chapter 10: Accessibility Requirements: Title 24 Chapter 11B & ADA
10.1 California Accessibility Framework: CBC Chapter 11B vs Federal ADA Standards 10.2 Accessible Routes, Entrances, Parking, and Site Arrival Points 10.3 Accessible Restrooms, Signage, Scoping, and Path of Travel Alteration Thresholds
11 Chapter 11: California Site Conditions & Natural Hazards
11.1 Seismic Hazard Mapping: Alquist-Priolo Earthquake Fault Zoning Act & Liquefaction 11.2 Wildland-Urban Interface (WUI) & Fire Hazard Severity Zones (CBC Chapter 7A & CFC Part 9) 11.3 Flood Hazard Zones (FEMA/DWR) & California Wind Exposure Categories
12 Chapter 12: Energy Efficiency: California Energy Code (Title 24 Part 6)
12.1 Energy Code Compliance Approaches: Prescriptive vs Performance & Time Dependent Valuation (TDV) 12.2 Mandatory Energy Measures: Envelope, HVAC, Lighting, Solar PV & Energy Storage Systems
13 Chapter 13: Sustainability (CALGreen) & Systems Integration
13.1 CALGreen (Title 24 Part 11) Mandatory Nonresidential & Residential Green Building Measures 13.2 Life-Cycle Cost Analysis (LCCA) & Value Engineering in California Practice 13.3 Building Systems Integration: MEP Coordination, Materials Evaluation & Acoustic Control
14 Chapter 14: Construction Document Requirements & Regulatory Coordination
14.1 CD Content, Detailing & Inter-Disciplinary Coordination for Agency Approval and Bidding 14.2 Authority Having Jurisdiction (AHJ) Hierarchy, Local Amendments & Local Finding Requirements 14.3 Reconciling Conflicting Codes, Standards, and Regulatory Mandates
15 Chapter 15: Plan Check & Permitting Processes
15.1 Permitting Procedures, Plan Check Review, Agency Comment Inquiries & Approval Pathways 15.2 Phased Permitting, Deferred Approvals, Encroachment Permits & Public Right-of-Way Coordination
16 Chapter 16: California Public Contract Code & Bidding Procedures
16.1 Public Works Bidding, Competitive Bidding Thresholds & Responsive vs Responsible Bidders 16.2 Subletting and Subcontracting Fair Practices Act & Subcontractor Listing Rules (PCC §§ 4100–4114) 16.3 California Prevailing Wage Requirements, DIR Registration & Certified Payroll Records
17 Chapter 17: California Mechanics Lien Law & Payment Remedies
17.1 20-Day Preliminary Notice Requirements & Timing (Civil Code § 8200) 17.2 Mechanics Liens, Recording Deadlines & Impact of Notice of Completion (Civil Code §§ 8400–8494) 17.3 Stop Payment Notices, Payment Bonds & Design Professional Liens (Civil Code §§ 8300–8319, 9350–9566)
18 Chapter 18: Construction Administration: Pre-Construction, Submittals, Changes & Field Observation
18.1 Pre-Construction & Pre-Installation Meetings and the Construction Manager's Impact on Services 18.2 Shop Drawings, Submittals & Architect's Deferred Submittal Review and Stamp 18.3 Construction Changes: Change Orders (CO), CCDs, ASIs & DSA Category A/B CCDs 18.4 Periodic Site Observations, Field Reports & the Means-and-Methods Boundary
19 Chapter 19: Inspection, Close-Out & Post-Construction Services
19.1 Special Inspections, Testing (CBC Chapter 17) & DSA/HCAI Continuous Field Inspection 19.2 Project Close-Out, Payment Applications (G702/G703), Retainage & California Warranty/Defect Limitations (CCP §§ 337.1 & 337.15) 19.3 Post-Construction Services, Record Documents & the Warranty Period 19.4 Construction Industry Standards, Detailing & Referenced Standards
3.3 Project Delivery Methods & Impact of Project Funding Sources
Key Takeaways Explain This Topic AI
Project delivery methods allocate contractual risk, speed, cost certainty, and design control differently across Design-Bid-Build (DBB), CMAR, Design-Build (DB), and Integrated Project Delivery (IPD).
California Public Contract Code §§ 22160–22169 authorizes local agencies to procure Design-Build projects using a two-step 'Best Value' selection process evaluating price, technical expertise, past performance, and safety.
A Bridging Architect (Criteria Architect) establishes preliminary program criteria and bridging documents (30-50% design) for a public owner, and is legally precluded from joining downstream Design-Build entities.
Public school projects funded via state bond measures (School Facility Program) administered by SAB/OPSC require final Division of the State Architect (DSA) approval prior to funding release.
Publicly funded projects trigger rigorous statutory compliance mandates, including Department of Industrial Relations (DIR) prevailing wages, Skilled and Trained Workforce quotas, and DVBE participation goals.
Last updated: September 2026
Project Delivery Methods & Impact of Project Funding Sources
Quick Answer: The chosen project delivery method dictates contractual privity, risk allocation, and the architect's legal relationship with the contractor. While Design-Bid-Build (DBB) remains the default for California public works under the Public Contract Code's lowest-responsible-bidder mandate, statutes such as California Public Contract Code (PCC) §§ 22160–22169 authorize local agencies to utilize Design-Build under a competitive "Best Value" selection process. Furthermore, project funding sources—whether private commercial financing, local Proposition 39 general obligation bonds, state School Facility Program (SFP) grants, or federal funds—impose rigorous architectural and administrative requirements, including Department of Industrial Relations (DIR) prevailing wage specifications, Skilled and Trained Workforce quotas, and strict DSA / OPSC closeout certification .
1. Spectrum of Project Delivery Methods
A project delivery method is the comprehensive organizational and contractual structure that defines how design, procurement, and construction services are coordinated, executed, and paid for. DESIGN-BID-BUILD (DBB) CONSTRUCTION MANAGEMENT AT RISK (CMAR)
- ┌────────────────────────┐ ┌────────────────────────┐
- │ OWNER │ │ OWNER │
- └───┬────────────────┬───┘ └───┬────────────────┬───┘
- │ │ │ │
- │ Design │ Construction │ Design │ Pre-con & Construction
- ▼ ▼ ▼ ▼ (GMP Contract)
- ┌─────────┐ ┌──────────┐ ┌─────────┐ ┌──────────┐
- │ARCHITECT│ │GENERAL │ │ARCHITECT│ │ CMAR / │
- └─────────┘ │CONTRACTOR│ └─────────┘ │ GC │
- └──────────┘ └──────────┘
- DESIGN-BUILD (DB) INTEGRATED PROJECT DELIVERY (IPD)
- ┌────────────────────────┐ ┌──────────────────────────────────────┐
- │ OWNER │ │ SINGLE MULTI-PARTY AGREEMENT │
- └───────────┬────────────┘ │ │
- │ Single Contract │ ┌─────────┐ ┌──────────┐ │
- ▼ │ │ OWNER │◄─────►│ARCHITECT │ │
- ┌────────────────────────┐ │ └────┬────┘ └────┬─────┘ │
- │ DESIGN-BUILD ENTITY │ │ │ │ │
- │ (Contractor + Arch) │ │ ▼ ▼ │
- └────────────────────────┘ │ ┌────────────────────────┐ │
- │ │ CONTRACTOR │ │
- │ └────────────────────────┘ │
- └──────────────────────────────────────┘
- A. Design-Bid-Build (DBB)
Structure: Two separate prime contracts (Owner-Architect and Owner-Contractor). Completely linear: Design → Bid → Construct.
Characteristics: Traditional default delivery method for public works. Design is 100% complete before competitive bidding.
Strengths: Maximum owner control over design aesthetics, materials, and program. Clear pricing established by competitive bidding among general contractors.
Weaknesses: Highly adversarial potential. Contractor bidding low may seek profit through aggressive change order claims. The owner bears the risk of design errors and omissions under the Spearin Doctrine (where the owner impliedly warrants the adequacy and accuracy of the architect's plans and specs to the contractor).
B. Construction Manager at Risk (CMAR / CM-GC)
Structure: Two separate prime contracts (Owner-Architect and Owner-CMAR). The Construction Manager acts as an advisory consultant during design (providing constructability reviews, scheduling, and value engineering) and converts to the general contractor prior to construction by issuing a Guaranteed Maximum Price (GMP) .
Strengths: Early contractor input during Design Development; early procurement of long-lead items; phased fast-track construction.
Weaknesses: Potential tension when negotiating the GMP; architect's design decisions are subject to aggressive cost critique by the CMAR.
C. Design-Build (DB)
Structure: A single contract between the Owner and a Design-Build Entity (DBE) . The architect is either a joint-venture partner, an employee of the builder, or a subcontractor to the general contractor.
Strengths: Single point of responsibility for both design and construction; eliminates owner's Spearin doctrine liability; fast-track delivery; reduced change order disputes.
Weaknesses: The architect's traditional role as independent advisor to the owner is eliminated; owner loses direct agency representation unless an independent Criteria Architect is retained.
D. Integrated Project Delivery (IPD)
Structure: A single multi-party agreement signed simultaneously by the Owner, Architect, General Contractor, and primary trade subcontractors.
Characteristics: Shared financial risk and reward; open-book accounting; collective target value design; waiver of liability among participants for ordinary negligence.
California Reality: Highly popular among large California private healthcare providers (e.g., Sutter Health) and technology campuses, but restricted in traditional public works due to competitive bidding statutes.
2. California Public Agency Delivery Authorization & The "Best Value" Process
In California, public agencies cannot automatically choose any delivery method. The California Public Contract Code (PCC) strictly controls how tax dollars are spent.
Traditional Competitive Bidding Mandate
By default, California public works contracts must be awarded through competitive bidding to the "lowest responsive, responsible bidder" (PCC § 20111 for school districts, PCC § 20128 for counties, PCC § 20162 for cities). A responsive bidder complies with all bid submission terms; a responsible bidder possesses the requisite trustworthiness, capacity, and experience.
Design-Build Authorization (PCC §§ 22160–22169)
To modernize public procurement, the California Legislature enacted PCC §§ 22160–22169 , granting broad authority to local agencies (cities, counties, and special districts) to utilize Design-Build for projects exceeding statutory dollar thresholds (typically $1 million) using a "Best Value" selection process rather than low-bid alone.
Under PCC § 22164 , the Best Value procurement process involves a structured two-step process:
Request for Qualifications (RFQ): Prequalifies design-build entities based on licensing, safety records (workers' comp experience modification rates), bonding capacity, and history of past performance.
Request for Proposals (RFP): Shortlisted teams submit competitive technical and price proposals. Under the statute, proposals are evaluated using weighted scoring criteria that must include:
- Price (minimum 10% weighting)
- Technical design and construction expertise (minimum 10% weighting)
- Life-cycle costs over 15+ years
- Safety record and skilled workforce commitments
- Past performance and project management approach
- The Bridging Architect (Criteria Architect)
When a California public agency utilizes Design-Build, it retains an independent architect—known as the Bridging Architect or Criteria Architect :
Responsibilities: Develops the project program, room data sheets, site master planning, performance specifications, and preliminary schematic designs (typically advanced to approximately 30% to 50% design).
Bridging Package: The public agency issues this bridging package within the RFP. The successful Design-Build Entity then completes 100% Construction Documents, secures permits, and builds the project.
Strict Legal Disqualification: Under California conflict-of-interest statutes (California Government Code § 1090), the Bridging Architect is legally precluded from joining, subcontracting with, or advising any of the competing Design-Build Entities bidding on the project.
Lease-Leaseback in California School Construction (Education Code § 17406)
In California K-12 public school construction, school districts frequently bypass traditional low-bid DBB by utilizing the Lease-Leaseback delivery method:
The school district leases its district-owned site to a selected developer/contractor for a nominal sum (e.g., $1.00).
The contractor constructs or modernizes the school facility.
The district leases the facility back through lease payments over a designated term, with title vesting in the district upon completion.
Following statutory reforms, Lease-Leaseback contracts must be awarded via an open, competitive "Best Value" procurement process, and contractors must utilize a prequalified pool of MEP subcontractors.
3. Project Delivery Methods Comparison
Delivery Method Contractual Structure Architect's Client Cost Certainty Point Primary Advantages Primary Risks / Disadvantages
Design-Bid-Build (DBB) Separate prime contracts for Architect and Contractor Project Owner Late (after competitive bidding concludes) High owner design control; transparent bidding; competitive pricing Adversarial relations; change order disputes; owner holds Spearin risk
CMAR / CM-GC Separate prime contracts for Architect and CMAR Project Owner Mid-design (when Guaranteed Maximum Price is set) Early constructability input; phased fast-track construction; reduced claims GMP negotiation friction; cost pressure on architectural detailing
Design-Build (DB) Single contract between Owner and Design-Build Entity Design-Build Entity (Contractor or JV) Early (fixed in DB proposal / RFP response) Single point of responsibility; fast schedule; eliminates Spearin risk Owner loses direct architectural advocacy; potential design quality compromises
Integrated Project Delivery (IPD) Single multi-party contract (Owner + Architect + GC) The Project / Unified Triad Continuous target value design Collaborative problem solving; shared risk/reward; no liability claims Requires sophisticated team; incompatible with standard public bidding laws
4. Impact of Project Funding Sources on Architectural Scope
The source of project capital dictates the statutory and administrative framework governing an architect's work in California:
A. Private Commercial Financing
Funding: Bank construction loans, commercial mortgages, private equity.
Architectural Requirements:
Lenders mandate Consent to Assignment agreements: if the developer defaults on the loan, the lender steps into the developer's shoes and assumes the right to use the architect's plans to finish the project.
Monthly payment application inspections: The architect must certify AIA G702/G703 payment applications, often accompanied by the lender's independent construction monitoring engineer.
B. Municipal General Obligation (G.O.) Bonds (Proposition 39)
Funding: Local municipal or school district bonds approved by local voters.
Statutory Controls: Proposition 39 bonds (passed by a 55% voter threshold) impose strict statutory oversight under the California Education Code:
Citizens' Bond Oversight Committee (CBOC): Independent citizen committee reviews all bond expenditures.
Restrictions on Funds: Funds can only be expended on facility construction, rehabilitation, and land acquisition—never on administrator salaries or general operating expenses.
Audits: Mandatory annual independent financial and performance audits require meticulous architectural recordkeeping of design change orders and fee modifications.
C. State Bond Measures & School Facility Program (SFP)
Funding: Statewide bond measures (e.g., Proposition 2, Proposition 13, Proposition 51) providing state matching grants for K-12 and community colleges.
Governing Bodies: Administered by the State Allocation Board (SAB) and the Office of Public School Construction (OPSC) .
Crucial Approval Milestone: Before a school district can receive funding apportionment from OPSC, the project construction documents must receive final plan approval and stamping from the Division of the State Architect (DSA) for structural safety, fire life safety, and accessibility, as well as educational plan clearance from the California Department of Education (CDE).
D. Federal Grants (FEMA, ARPA, Inflation Reduction Act)
Funding: Federal disaster mitigation, municipal infrastructure grants, or IRA energy direct-pay subsidies.
Requirements: Compliance with the federal Davis-Bacon Act (federal prevailing wage), NEPA environmental reviews, Buy America / Build America mandates, and strict federal audit reporting.
5. Funding-Driven Statutory Labor and Contracting Mandates
When projects involve public funding in California, architects must integrate specific statutory requirements directly into the project specifications (Project Manual / CSI Division 00 and 01):
A. California Prevailing Wage Law (Labor Code § 1720 et seq.)
Mandates that all workers on a public works project valued over $1,000 must be paid not less than the general prevailing per diem wage rates established by the Department of Industrial Relations (DIR) .
Contractor DIR Registration: No contractor or subcontractor can bid on or be awarded a public works contract unless registered with the DIR.
Electronic Certified Payroll Records (eCPR): Contractors must submit weekly certified payrolls electronically to the California Labor Commissioner.
Architect's Role: The architect must verify that the Project Manual includes mandatory statutory language notifying all prospective bidders that prevailing wages apply.
B. Skilled and Trained Workforce Requirements (PCC § 2600 et seq.)
California statutes mandate that for certain alternative delivery projects (including Design-Build and Lease-Leaseback school projects), the contractor and all tiered subcontractors must employ a "Skilled and Trained Workforce" .
Under PCC § 2601, this mandates that a defined statutory percentage (typically 60%) of all journeypersons in apprenticeable crafts must be graduates of an apprenticeship program approved by the California Apprenticeship Council.
C. DVBE & DBE Participation Goals
Disabled Veteran Business Enterprise (DVBE): California state-funded public works contracts (including projects funded through the State Allocation Board / OPSC) mandate a 3% DVBE participation goal (California Military and Veterans Code § 999 et seq.). Prime architects and general contractors must document good-faith outreach efforts or sub-consultant partnerships.
Disadvantaged Business Enterprise (DBE): Federally funded transportation or municipal projects require compliance with federal DBE participation percentages under 49 CFR Part 26.
D. DSA Project Closeout and Certification (Form DSA-6)
For California public school projects under DSA jurisdiction:
Final grant funds and remaining retainage cannot be cleanly released until the project receives a DSA Certification of Compliance .
The architect, structural engineer, project inspector, and general contractor must submit final verified reports ( Form DSA-6 / DSA-6-AE).
Failure to achieve certified closeout results in a "closed without certification" letter, which legally halts future state funding apportionments for the school district.