Study guide
16.2 Subletting and Subcontracting Fair Practices Act & Subcontractor Listing Rules (PCC §§ 4100–4114)
California Supplemental Examination CSE
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: California Architects Practice Act & Professional Practice
1.1 Licensing, Board Authority, and Unlicensed Practice Exceptions 1.2 Mandatory Written Contracts & Required Provisions 1.3 Architect's Stamp, Signature, and Professional Liability
2 Chapter 2: Professional Conduct, Ethics & Business Entities
2.1 Rules of Professional Conduct & Disciplinary Grounds 2.2 Permissible Business Entities, Firm Names, and Filing Requirements 2.3 Copyright, Instruments of Service & Ownership of Architectural Documents
3 Chapter 3: Contractual Roles, Scope & Consultant Agreements
3.1 Standard Owner-Architect Agreements (AIA B101 / B102) & California Practice Realities 3.2 Consultant Selection, Prime-Consultant Agreements & Liability Flow-Down (AIA C401) 3.3 Project Delivery Methods & Impact of Project Funding Sources
4 Chapter 4: Risk Management, Dispute Resolution & Project Planning
4.1 Professional Standard of Care & Managing Contractual Risk and Liability 4.2 Dispute Resolution in California Practice: Mediation, Arbitration, and Litigation 4.3 Project Scheduling, Budgeting Assumptions, and Milestone Approvals
5 Chapter 5: Site Feasibility, Schematic Design & Discretionary Approvals
5.1 Site Feasibility Studies, Existing-Conditions Due Diligence & Project Impacts 5.2 Programming, Schematic Design Development & Stakeholder Engagement 5.3 Local Land-Use Control: General Plans, Zoning, Specific Plans & Local Ordinances 5.4 The Discretionary Approval Process: Use Permits, Variances, Design Review & Hearings 5.5 Entitlement Exhibits, Conditions of Approval & Leading the Approval Team
6 Chapter 6: Environmental Review & CEQA Compliance
6.1 CEQA Regulatory Framework: Lead, Responsible, and Trustee Agencies 6.2 CEQA Process: Statutory & Categorical Exemptions, Initial Studies, and (Mitigated) Negative Declarations 6.3 Environmental Impact Reports (EIR) & Official Filings (NOP, NOC, NOD, NOE)
7 Chapter 7: California Coastal Act & Specialized Regional Regulations
7.1 California Coastal Commission & Coastal Development Permits (CDP) 7.2 Local Coastal Programs (LCP), Coastal Zone Boundaries, and Appeals 7.3 Clean Air Act (CARB/AQMDs) & Clean Water Regulations (Porter-Cologne, RWQCB & SWPPP)
8 Chapter 8: State Agency Jurisdictions: DSA, HCAI & Essential Services
8.1 Division of the State Architect (DSA): Field Act & Public K-12/Community College Oversight 8.2 Department of Health Care Access and Information (HCAI): Alfred E. Alquist Act & Healthcare Facility Classification 8.3 Essential Services Buildings Seismic Safety Act (ESBSSA) & California Historical Building Code (CHBC)
9 Chapter 9: California Building Code (CBC Title 24 Part 2) Core Architecture Provisions
9.1 Occupancy Classifications, Building Heights, and Allowable Floor Areas (CBC Chapters 3 & 5) 9.2 Fire and Smoke Protection Features, Fire Barriers, and Fire-Resistance Ratings (CBC Chapter 7) 9.3 Means of Egress, Occupant Load Calculations, and Exit Separation (CBC Chapter 10) 9.4 California Health and Safety Code: Building Standards Law, State Housing Law & Health Mandates
10 Chapter 10: Accessibility Requirements: Title 24 Chapter 11B & ADA
10.1 California Accessibility Framework: CBC Chapter 11B vs Federal ADA Standards 10.2 Accessible Routes, Entrances, Parking, and Site Arrival Points 10.3 Accessible Restrooms, Signage, Scoping, and Path of Travel Alteration Thresholds
11 Chapter 11: California Site Conditions & Natural Hazards
11.1 Seismic Hazard Mapping: Alquist-Priolo Earthquake Fault Zoning Act & Liquefaction 11.2 Wildland-Urban Interface (WUI) & Fire Hazard Severity Zones (CBC Chapter 7A & CFC Part 9) 11.3 Flood Hazard Zones (FEMA/DWR) & California Wind Exposure Categories
12 Chapter 12: Energy Efficiency: California Energy Code (Title 24 Part 6)
12.1 Energy Code Compliance Approaches: Prescriptive vs Performance & Time Dependent Valuation (TDV) 12.2 Mandatory Energy Measures: Envelope, HVAC, Lighting, Solar PV & Energy Storage Systems
13 Chapter 13: Sustainability (CALGreen) & Systems Integration
13.1 CALGreen (Title 24 Part 11) Mandatory Nonresidential & Residential Green Building Measures 13.2 Life-Cycle Cost Analysis (LCCA) & Value Engineering in California Practice 13.3 Building Systems Integration: MEP Coordination, Materials Evaluation & Acoustic Control
14 Chapter 14: Construction Document Requirements & Regulatory Coordination
14.1 CD Content, Detailing & Inter-Disciplinary Coordination for Agency Approval and Bidding 14.2 Authority Having Jurisdiction (AHJ) Hierarchy, Local Amendments & Local Finding Requirements 14.3 Reconciling Conflicting Codes, Standards, and Regulatory Mandates
15 Chapter 15: Plan Check & Permitting Processes
15.1 Permitting Procedures, Plan Check Review, Agency Comment Inquiries & Approval Pathways 15.2 Phased Permitting, Deferred Approvals, Encroachment Permits & Public Right-of-Way Coordination
16 Chapter 16: California Public Contract Code & Bidding Procedures
16.1 Public Works Bidding, Competitive Bidding Thresholds & Responsive vs Responsible Bidders 16.2 Subletting and Subcontracting Fair Practices Act & Subcontractor Listing Rules (PCC §§ 4100–4114) 16.3 California Prevailing Wage Requirements, DIR Registration & Certified Payroll Records
17 Chapter 17: California Mechanics Lien Law & Payment Remedies
17.1 20-Day Preliminary Notice Requirements & Timing (Civil Code § 8200) 17.2 Mechanics Liens, Recording Deadlines & Impact of Notice of Completion (Civil Code §§ 8400–8494) 17.3 Stop Payment Notices, Payment Bonds & Design Professional Liens (Civil Code §§ 8300–8319, 9350–9566)
18 Chapter 18: Construction Administration: Pre-Construction, Submittals, Changes & Field Observation
18.1 Pre-Construction & Pre-Installation Meetings and the Construction Manager's Impact on Services 18.2 Shop Drawings, Submittals & Architect's Deferred Submittal Review and Stamp 18.3 Construction Changes: Change Orders (CO), CCDs, ASIs & DSA Category A/B CCDs 18.4 Periodic Site Observations, Field Reports & the Means-and-Methods Boundary
19 Chapter 19: Inspection, Close-Out & Post-Construction Services
19.1 Special Inspections, Testing (CBC Chapter 17) & DSA/HCAI Continuous Field Inspection 19.2 Project Close-Out, Payment Applications (G702/G703), Retainage & California Warranty/Defect Limitations (CCP §§ 337.1 & 337.15) 19.3 Post-Construction Services, Record Documents & the Warranty Period 19.4 Construction Industry Standards, Detailing & Referenced Standards
16.2 Subletting and Subcontracting Fair Practices Act & Subcontractor Listing Rules (PCC §§ 4100–4114)
Key Takeaways Explain This Topic AI
The Subletting and Subcontracting Fair Practices Act (PCC §§ 4100–4114) was enacted to eliminate the unethical practices of 'bid shopping' and 'bid peddling' in public works construction, ensuring fair treatment of subcontractors and protecting public construction quality.
A prime contractor submitting a formal bid on a public works project must list every subcontractor who will perform work or labor or render service in excess of one-half of one percent (1/2 of 1%) of the prime contractor's total bid, or $10,000, whichever is greater.
Under PCC § 4106, if a prime contractor fails to list a subcontractor for a portion of work exceeding the statutory threshold, the prime contractor agrees that they are fully qualified to perform that work themselves, and MUST perform that work using their own forces.
PCC § 4107 establishes strict, exclusive statutory grounds for subcontractor substitution; a prime contractor cannot substitute a listed subcontractor without the public agency's written consent following a mandatory 5-working-day notice and hearing procedure.
Violating the Subletting and Subcontracting Fair Practices Act subjects the prime contractor to severe statutory penalties, including contract cancellation under PCC § 4110, an administrative monetary penalty of up to 10% of the subcontract amount, and disciplinary action by the CSLB.
Last updated: September 2026
Subletting and Subcontracting Fair Practices Act & Subcontractor Listing Rules (PCC §§ 4100–4114)
In public works contracting, general (prime) contractors rely heavily on specialty trade subcontractors to execute major building systems—such as structural steel, HVAC, electrical, plumbing, glazing, and roofing. Prior to statutory regulation, the public construction industry was frequently undermined by predatory bidding tactics that compromised project quality and exploited trade contractors. To prevent these market abuses, the California Legislature enacted the Subletting and Subcontracting Fair Practices Act , codified in Public Contract Code (PCC) Sections 4100 through 4114 . For architects administering public works projects in California, mastering the mandatory subcontractor listing thresholds, understanding the legal consequences when a prime contractor omits a trade, enforcing the strict statutory grounds and procedures for subcontractor substitution, and recognizing statutory penalties are essential administrative obligations.
Legislative Intent: Eliminating Bid Shopping and Bid Peddling
Public Contract Code Section 4101 explicitly articulates the legislative purpose of the Act: to prevent the practices of bid shopping and bid peddling in connection with the construction, alteration, and repair of public works projects. The Legislature found that these practices result in poor quality of material and workmanship, deprive the public of the full benefits of fair competition, stimulate widespread insolvencies among specialty contractors, and lead to contract disputes and construction delays:
Bid Shopping: Occurs when a prime contractor, after being awarded the public contract (or after public bid opening reveals them as the apparent low bidder), uses the lowest subcontractor's bid price as leverage to pressure other subcontractors into lowering their pricing. The prime contractor pockets the resulting difference as unearned windfall profit, while the coerced subcontractor is forced to cut corners on labor, materials, and safety to survive.
Bid Peddling: Occurs when an unlisted subcontractor approaches the winning prime contractor after bid opening and offers an undercut price to induce the prime contractor to drop the subcontractor whose price was originally incorporated into the prime bid.
The Act halts these practices by legally binding the prime contractor to the subcontractors listed in the bid at the time of bid submission.
Mandatory Subcontractor Listing Threshold & Requirements
Under PCC Section 4104 , any general contractor submitting a formal bid on a public works project must include a completed Subcontractor Listing Form identifying specific specialty subcontractors:
The Listing Threshold (PCC § 4104(a)(1))
The prime contractor must list any subcontractor who will perform work, labor, or render service to the prime contractor in an amount in excess of one-half of one percent (0.5%) of the prime contractor's total bid , or $10,000 , whichever is greater.
Streets, Highways, and Bridges Exception: For public works construction involving streets, highways, or bridges, the statutory threshold is strictly one-half of one percent (0.5%) of the prime contractor's total bid , or $10,000 , whichever is greater (under PCC § 4104(a)(2)).
Required Listing Information
For each subcontractor performing work exceeding the statutory threshold, the prime contractor must explicitly provide:
- Subcontractor Legal Business Name: The precise legal name under which the specialty contractor is licensed;
- Business Address: The location of the subcontractor's place of business;
- CSLB License Number: The active California Contractors State License Board license number;
DIR Public Works Registration Number: The active Department of Industrial Relations registration number (pursuant to Labor Code § 1725.5);
Portion of Work: The specific trade or scope of construction to be performed (e.g., "Division 26 - Electrical Distribution" or "Structural Steel Fabrication and Erection").
One Subcontractor Per Trade Scope (PCC § 4104(b))
The prime contractor cannot list more than one subcontractor for the same portion of work unless the prime bid explicitly designates the distinct, non-overlapping geographic or physical portions of the work that each subcontractor will execute.
Prime Contractor Assumption of Work (PCC § 4106)
A critical exam concept and contractual rule is codified in Public Contract Code Section 4106 :
If a prime contractor fails to specify a subcontractor, or specifies more than one subcontractor for the same portion of work in excess of one-half of one percent of the prime contractor's total bid, the prime contractor agrees that they are fully qualified to perform that portion of work themselves, and MUST perform that portion of work using their own forces.
If the prime contractor fails to list a trade contractor for a scope exceeding the threshold, the prime contractor is legally prohibited from subcontracting out that work after contract award without obtaining formal statutory substitution approval from the public agency. Furthermore, the prime contractor must possess the appropriate classification of CSLB license to legally self-perform that trade. A general building contractor (Class B) who omits listing a fire sprinkler or roofing subcontractor exceeding the threshold cannot legally self-perform specialty trade work requiring specialized C-class licensing (such as C-16 Fire Protection) unless they hold that specific specialty license.
Strict Statutory Grounds for Subcontractor Substitution (PCC § 4107)
Once bids are opened, the prime contractor has no unilateral power to replace, remove, or substitute a listed subcontractor. Under PCC Section 4107 , a prime contractor cannot substitute a listed subcontractor without the formal written consent of the awarding public authority . The public agency may grant consent only under the following strictly defined, exclusive statutory circumstances:
Refusal to Execute Written Contract (§ 4107(a)(1)): When the listed subcontractor, after having had a reasonable opportunity to do so, fails or refuses to execute a written subcontract presented by the prime contractor that reflects the scope and pricing of the subcontractor's bid.
Bankruptcy or Insolvency (§ 4107(a)(2)): When the listed subcontractor becomes bankrupt or enters insolvency proceedings.
Failure to Perform (§ 4107(a)(3)): When the listed subcontractor fails or refuses to perform its subcontract obligations in accordance with project plans and specifications.
Failure to Meet Bond Requirements (§ 4107(a)(4)): When the listed subcontractor fails or refuses to meet the reasonable bonding requirements of the prime contractor, provided the prime contractor specified in its written solicitation that bonds would be required.
Inadvertent Clerical Error (§ 4107(a)(5)): When the prime contractor made an inadvertent clerical error in listing the wrong subcontractor name, subject to the strict procedural rules of PCC Section 4107.5.
Lack of Valid CSLB License (§ 4107(a)(6)): When the listed subcontractor is not properly licensed by the Contractors State License Board pursuant to the Business and Professions Code.
Substantially Unsatisfactory Work or Delay (§ 4107(a)(7)): When the awarding authority determines that the work performed by the listed subcontractor is substantially unsatisfactory and not in substantial accordance with the plans and specifications, or that the subcontractor is substantially delaying or disrupting progress.
Lack of DIR Registration or Ineligibility (§ 4107(a)(8) & (9)): When the listed subcontractor fails to pay prevailing wages or is debarred under Labor Code Sections 1777.1 or 1777.7, or is not registered with the Department of Industrial Relations under Labor Code Section 1725.5.
Administrative Substitution Procedures & Due Process Hearings
To safeguard listed subcontractors from unlawful removal, PCC Section 4107 mandates strict administrative due process:
1. Mandatory 5-Working-Day Written Notice
Before granting consent to substitute a listed subcontractor (under grounds 1 through 4, 6, or 7), the awarding public authority must give written notice by certified or registered mail to the listed subcontractor , detailing the prime contractor's request and the specific statutory grounds asserted.
2. Subcontractor Right to Object
The listed subcontractor has five (5) working days from receipt of the notice to submit written objections to the proposed substitution to the awarding authority.
3. Public Agency Board Hearing
If the listed subcontractor files timely written objections within 5 working days, the awarding authority must conduct a formal public hearing . The awarding agency's governing board (or a designated administrative hearing officer) hears testimony, reviews evidence, and evaluates whether the statutory grounds have been proven. The public authority must issue written findings. The prime contractor cannot substitute the subcontractor or permit the substituted firm on the jobsite until the agency issues formal written approval.
Inadvertent Clerical Error Substitution Procedure (PCC § 4107.5)
Where a prime contractor asserts an inadvertent clerical error in listing (e.g., typing "Acme Mechanical" instead of "Apex Mechanical"), extreme statutory safeguards apply:
The prime contractor must deliver written notice of the error to the awarding authority, the listed subcontractor, and the intended subcontractor within two (2) working days after the bid opening.
The listed subcontractor has six (6) working days from receipt to submit written objections.
The awarding authority holds a public hearing and must verify affidavits from both the prime contractor and intended subcontractor proving that the error was genuine and not a pretext for bid shopping.
Statutory Penalties for Violating the Act
Violations of the Subletting and Subcontracting Fair Practices Act carry severe statutory consequences:
1. Contract Cancellation (PCC § 4110)
The awarding public agency has the statutory right to cancel the prime contract entirely, or to terminate the prime contractor for cause.
2. Monetary Penalties (PCC § 4110)
The awarding authority may assess an administrative financial penalty against the prime contractor of up to ten percent (10%) of the amount of the subcontract involved . The penalty funds are deposited into the public agency's general fund.
3. CSLB Disciplinary Action (PCC § 4111)
Violating any provision of the Act constitutes professional misconduct under the Contractors State License Law (Business and Professions Code Section 7114). The Contractors State License Board (CSLB) can suspend or revoke the prime contractor's license and impose civil citations.
Table: Subcontractor Listing Rules, Statutory Grounds for Substitution & Penalties
Statutory Element Public Contract Code Reference Legal Requirement / Threshold Procedural Protocol
Mandatory Listing Threshold PCC § 4104(a)(1) Work in excess of 1/2 of 1% (0.5%) of prime bid, or $10,000 , whichever is greater Listed on bid form at time of bid submission; one sub per scope
Streets & Highways Threshold PCC § 4104(a)(2) Work in excess of 1/2 of 1% of prime bid, or $10,000 , whichever is greater Subcontractor name, business address, CSLB #, DIR #, and scope
Failure to List Subcontractor PCC § 4106 Prime contractor agrees they are qualified and must perform work with own forces Subcontracting prohibited post-award; must possess appropriate CSLB license
Lawful Substitution Grounds PCC § 4107(a)(1)–(9) Refusal to contract, insolvency, non-performance, bond failure, clerical error, lack of license/DIR Exclusive statutory list; unilateral substitution strictly prohibited
Substitution Notice Period PCC § 4107(a) Public agency must send written notice to listed subcontractor Subcontractor has 5 working days to file written objections
Substitution Hearing PCC § 4107(a) Mandatory public hearing if sub objects within 5 days Public agency governing board hears evidence and issues written findings
Clerical Error Notice PCC § 4107.5 Prime must give notice within 2 working days of bid opening Listed sub has 6 working days to object; sworn affidavits required
Statutory Monetary Penalty PCC § 4110 Agency may assess penalty up to 10% of subcontract amount Penalty paid to public agency fund; contract cancellation authorized
Professional Discipline PCC § 4111 / B&P § 7114 Grounds for CSLB license suspension or revocation Administrative complaint filed with Contractors State License Board
CSE Exam Traps & Practical Takeaways
Trap 1: Calculating the Listing Threshold: Candidates must remember the exact math: 1/2 of 1% (0.005) of the total prime bid, or $10,000, whichever is greater. On a $5,000,000 public project, the threshold is $25,000 (0.005 x $5,000,000). Any subcontract exceeding $25,000 must be listed.
Trap 2: Subcontracting After Failing to List: A prime contractor cannot "fix" an omitted subcontractor after bid opening by negotiating a subcontract. Under PCC § 4106, omitting the subcontractor creates a binding legal covenant that the prime must perform the work with their own forces.
Trap 3: Bid Shopping Disguised as Substitution: An owner or architect cannot approve a substitution simply because the prime contractor found another subcontractor who can do the work for $50,000 less. Unlawful price reduction is the exact definition of bid shopping and violates PCC § 4107.
Trap 4: 5 Working Days Objection Timeline: Under PCC § 4107, the listed subcontractor has 5 working days —not calendar days—from receipt of the public entity's notice to submit written objections and demand a public hearing.